I am considering deploying several of these for our church to provide internet access. When reading the manual, I found on the last few pages that the device only supports a max of 63 users at a time. Is that correct? If so, any way to add more ?
View 1 Replies
I have a WAP4410N access point. In the datasheet, it shows that the Antenna Gain in dBi as 2. I need to increase the range of the access point by replacing the antenna with a 7dB one. I would like to know the maximum dBi supported by this access point.
View 0 Replies View RelatedI am trying to set up a Linksys WAP4410N on our network. We are trying to run it using unrestricted access, but it is requiring a pin number. The prompt I get when trying to connect to the WAP is that the number should be in the original documentation. I can not find the original documentation and I cannot log into the WAP to find the PIN number.
View 1 Replies View RelatedI have gone through the data sheet of WAP4410N,bu have got nothing about the scalability of MAC address filter on WAP4410N?
View 1 Replies View RelatedMy new laptop is asking for pin number I have a wap4410n.
View 1 Replies View RelatedI have a question regarding the number of computers connecting to a single wireless router. I want my internet connection at home to be used only by my laptop. I have my connection secured by password and etc, but I was wondering if there is a setting I can use to control the number of computers connected to a wireless router?
View 2 Replies View RelatedI wanted to know if anyone can say with certainty how many clients can stay connected 'Aironet 1140 series. I state that I should connect WiFi in about 350 clients.
View 6 Replies View RelatedThis is a feature that I have researched for by looking at ISRs G2 data sheets and cisco.com website.The number of users that can be supported or the recommended number of users per router chassis/model is not mentioned anywhere.However this is mentioned in the Cisco 880 ISR data sheet. What are the number of users that can be supported or the recommended number of users on Cisco 1900/2900/3900 ISRs?
View 4 Replies View RelatedI say the answer is ten. That means ten hosts can be behind the firewall and hit the internet. The eleventh doesn't get to go out. I'm being told by a coworker that the "10" in the part number refers to the number of IPsec VPN peers.
Who's right?
I say if you want an unlimited number of users on the inside to be able to get to the internet, you need the ASA5505-SEC-BUN-K9
Mfg. Part: ASA5505-SEC-BUN-K9
Mfg. Part: ASA5505-50-BUN-K9
Mfg. Part: ASA5505-BUN-K9
Cisco ASA 5505 10-User Bundle includes 8-port Fast Ethernet switch, 10 IPsec VPN peers, 2 Premium VPN peers, Triple Data Encryption Standard/Advanced Encryption Standard (3DES/AES) license ASA5505-BUN-K9
Im using AIR-LAP1142N-N-K9 access points (it supports b/g/n). Somestimes the AP has up to 80 users connect to it.SOme recommends the AP should have between 25-35 users max.Any one know the recommend maximum number of users connect to a AP? And how can you tell the traffic going through the AP is congested?
View 1 Replies View RelatedCan i connect about 12 devices (laptops and mobile phones) to a 8 mbps or 16 mbps wifi router?
View 1 Replies View RelatedIs it possible to configure WLC so that only one user can connect to wireless network at a time with one login? We have WLC5508 (7.2.103.0) web authentication with LDAP (Active Directory).
View 2 Replies View RelatedHow many user accounts i can create to a Cisco ASA box? Say for example a Cisco ASA 5510 or Cisco ASA 5520?
View 5 Replies View RelatedI have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
I have some tunnels which terminate to my home router. I'm allowing the other ends of the tunnels to use my voice setup. I need to prepend *67 to all called numbers which don't originate from my house. I don't want people calling my home number based on the caller-id number they see when someone across one of the tunnels calls.
So if 5008 calls 212-333-4444 I want it sent to my provider as *672123334444. If 5001 calls a number, I don't want it touched. Can I do this? I can use IOS or CUCM here.
How to increase my Laptop wireless range?
View 2 Replies View Relatedi am using wlc 4402 with a mgt ip 172.26.150.x/24 and ap manager ip 172.26.150.x/24, my all ap get the ip address from dhcp . currently in dhcp server 172.26.150.3 to 254 dhcp scope is configured. at mysite some devices are configured like ipad,iphone or galaxy tab with mac binding in dhcp server. now this pool is almost full. i have a policy configured for these devices for mac binding is done in DHCP. to increase pool what are the changes i need to do in wlc. what are the changes i need to do in dhcp server . is policy made for mac binding in dhcp server will get affected by this ?
View 2 Replies View Relatedhow to increase download and browsing speed using dial up connection using nokia mobile phone as a modem
View 2 Replies View Relatedworks well upstairs but does not work well about sixty feet from the router
View 5 Replies View RelatedI purchased and installed a new EA4500 wireless router. At the same time i had a new Voip phone system installed as well which i'm having issues with. The main issue is that my phones communicate with the service every 240 seconds....the issue is that my NAT timeout is below that 240 threshold. Thus my phones go in and out constantly. increasing the NAT Timeout.
View 5 Replies View RelatedThe GUI times out after 60 seconds.
Since the the "exec-timeout" setting has a default of 10 minutes (if I'm not mistaken), I don't think I could change the timeout value with that command.
Under the "Association" tab of the GUI, there is an "Activity Timeout" subtab and settings for 5 device classes, all set at 60 seconds.
I would guess the setting in question can be configured here. Is the client station device class what I'm after?
I have an integrated 881W with a built in 801 access point. I'm interested in increasing the range of my AP. I'm interested in considering any configuration changes while still maintaining support for N. I've included a copy of my running config.As well, I've heard of high gain antennas. I'm using the default antennas that came with the 881W. If there are better antennas that I can buy to increase my range, I'm interested in considering that as well.
View 10 Replies View Relatedi use college wifi.but college authority provide very slow download speed .how to increase this speed.
View 2 Replies View RelatedI just installed a new EA4500 and the range is terrible. How can I increase it?
View 1 Replies View RelatedI just got a new modem and was also hoping to boost the speed of my router without buying a new one. Are there any ways to increase the speed of the modem i already have?
View 2 Replies View RelatedI have my router and modem in an upstairs office. I get terrific signal strenth and wifi connections throughout 80% of my home. I would like to shore up that remaining 20%.
I cannot realistically move my EA4500 to a "more central" locationBefore purchasing this router, I used a netgear + netgear extender. They worked horrifically together along with my wifi devices - they dropped signals every 4-5 minutes, even with bare-bones data usage. (I've had no connectivity issues, thus far, with the Linksys product)My home has two levels - no basement, no crazy concrete walls or anything. I figured on installing an extender OR another EA4500 downstairs to extend my signal. How two EA4500's work together, if anyone has a similar set up, compared to how (and what model) an extender may work to boost my signal distance in this situation. Primarily, in that "20%" deadzone, I need to use an iPad / iPhone - nothing that would consume tons of bandwidth.
I have an E1000 router in my office with a cat5 cable going to my daughters bedroon thru several doors and around some corners. She (recently moved back in) has an E1000 router also.I need to know how to use both routers to increase the wireless signal in her bedroom.I have not tried anything yet.The router in my office is configured with an address of 192.168.2.1.
View 7 Replies View RelatedI've been using the WRT310N and noticed that the range is quite poor--I've noticed this in two different houses.I've tried using an old repeater but it is a G repeater so it seems to actually make things worse i.e. a remote device will work slightly better with an unrepeated N signal than a repeated G (router is a in mixed mode).
View 3 Replies View RelatedI have a cisco WAG120N with me.wifi range is very less, means my devices won't catch the wifi even if they are 5 meters away from the router. Ways to increase the wifi range of this router. I dont want to use any repeater or any such stuff, just want to achieve a far more range with te existing device.
View 9 Replies View RelatedWe have a new e1000 router that was having trouble reaching the TV for Netflix movie streaming. Too many walls and too much distance. A simple solution was to direct the signals from the router by placing aluminum foil behind the router so all the signal was going towards the TV rather than in an 360 degree circle. Now the streaming works great! After the movie is done I remove the foil and everything looks just like it should.
View 9 Replies View RelatedI have a Cisco-Linksys WRT310N V2 Wireless-N Gigabit Router and was wondering if there is a setting (which I could not find in the admin control panel) to increase the range to catch internet connection. My house is large, and one portion has a bad connection to it because the router is sitting upstairs on the other end. If there is no setting, is there a external add on I can get to increase the internet range?
View 9 Replies View Relatedif Linksys will be increasing the size limitation of the E4200 USB storage devices? Will the next firmware allow larger drive sizes? I only bought the thing to share via the router my digital content that is stored on an 8TB external device. What is the perpose to the limit in the first place? Is this a hardware or software limitation of the device?
View 2 Replies View RelatedI have read about pluggingthe WRT54GS into the E4200 to go back to the distance of the old WRT54GS. I get no distance out of the E4200 with RE1000 extender.
View 2 Replies View Related
