I know it is possible to create custom web auth splash pages on the WLC 5508. Is it also possible to embedd a small document (less than 1MB) that users can download directly from the controller? I need this for providing the terms of use for the Guest WLAN.
View 3 RepliesAt present I have a WLC5508 as a guest anchor in a DMZ and a web-auth passthrough WLAN configured. There is a custom web bundle providing a terms and conditions page.
We want to start to capture the minimum data from a user that logs onto the guest wireless ( email address ) and would like to use the check email function on the controller - BUT - at the same time move from using the web bundle locally hosted splashpage on the controller to an external web server provided splashpage / walled garden.
From my understanding not sure that this is possible as the email check function is only valid in passthrough I think.
I want to setup a webpage for my guest network (no authentication) users. When the client connects to the open guest network and upon opening a browser they would be directed to a survey that I would like them to take, if they don't want to take it they can begin browsing to other sites without issue. How do I do this on a my 5508 WLC?
View 12 Replies View RelatedWe’re currently using 5508 WLC’s and leveraging Cisco ISE for radius/authentication rule sets.I’m trying to get a splash page to flash and then redirect to a website after a successful authentication to an SSID. Everything on the wireless side works with no splash page (users connect to SSID,authenticate with AD credentials using 802.1X PEAP to our Cisco ISE box, and gain access to the network).When I enable ‘Splash Page Web Redirect’ on the WLC (under L3 security), I’m unclear on the ISE box where I set this up. When I look in the Cisco documention it says:Splash Page Web Redirect—If you select this option, the user is redirected to a particular web page after 802.1X authentication successfully completes. After the redirect, the user has full access to the network. You can specify the splash web page on your RADIUS server. How I specify this on the ISE box? Or am I totally off base?
View 10 Replies View RelatedI have implemented a Guest WLAN solution as per the recommended design from Cisco. We have two internal WiSM2 controllers providing services for Internal secure SSIDs. Both these controllers are members of a Mobility and RF management group.
Two 5508 controllers have been installed in our DMZ for resilience and have been placed into a separate Mobility group. All controllers (internal and external) have been linked together as mobility neighbours in a full mesh and a new SSID for Web Guest traffic has been anchored to the controllers in the DMZ.
Web page authentication works perfectly fine, but I cannot for the life of me get the MAC filtering override to work, i.e. if a MAC address is present, do not redirect to the splash page for web auth. I know I can get around this by just creating two separate SSIDs. But the business is used to just having the one SSID for all guest traffic. Is this a known limitation when anchoring SSIDs to controllers in the DMZ ?
I am trying to create a welcome screen for people who join the guest network on my aironet 1040.Webpage pass-through is really what I want but I know that doesn't work on a 1040.What does: IP redirect, Conditional Web redirect or Splashpage redirect?
View 1 Replies View RelatedI have setup load-balancing on an ACE 4710 for HTTP for Sharepoint 2010. The Server Admin says that the IIS server will recognize the right site by DNS name. Problem is I have no clue how to make sure the servers get the DNS name passed to them. They says this is for a multi-homing setup so that we can run multiple sites using the same VIP to the same Serverfarm. How do I do this? I keep getting the IIS splash page since the real server cannot determine the IIS site that I am supposed to access.
View 2 Replies View RelatedI am administrating a wireless network consisting of 11 APs, ASA 5510, WLC 4402 and Router 1760.The network is sharing an internet connection to all guests without charge so I have no need for authorisation of guests.I would like to implement a splash page that would be shown to all clients when they first connect. The splash page is supposed have only the basic information about the provided service and no logon.Is there a way to do this without purchasing an ACS?
View 3 Replies View RelatedI am trying to upload a customized web-auth bundle to a WLC 5508 and having some issues.I have downloaded the web-auth bundle from Cisco and used this as a template to create the web pages.I seem to recall that there is only a couple of Windows tools that you can use to TAR the file such as TUGZIP and IZARC. Anyway I have tried both and I still cannot get the file to extract. I have tried to strip the file out so that I only send up the login.html page and even this does not work.I am using a software release 7.0.220.0.
View 6 Replies View RelatedWe have recently implemented a 3rd party certificate for the guest access, currently have a WLC 5508 that has a Vlan directly connected to our DMZ firewall and NATed out. The problem is when I have installed a 3rd party certificate as per the following link URL
The DNS host name that I entered into the DNS Host name section is not resolved. If I remove the DNS name and leave the virtual ip address 1.1.1.1 then it works fine but just comes back with untrusted message.
I have implemented a Guest WLAN solution as per the recommended design from Cisco. We have two internal WiSM2 controllers providing services for Internal secure SSIDs. Both these controllers are members of a Mobility and RF management group.
Two 5508 controllers have been installed in our DMZ for resilience and have been placed into a separate Mobility group. All controllers (internal and external) have been linked together as mobility neighbours in a full mesh and a new SSID for Web Guest traffic has been anchored to the controllers in the DMZ.
Web page authentication works perfectly fine, but I cannot for the life of me get the MAC filtering override to work, i.e. if a MAC address is present, do not redirect to the splash page for web auth.
I am running into an issue with disabling the web-auth secure web on an 5508 anchor WLC running 7.2.110. After the WLC rebooted, the guest authentication portal didn't show up...I could see the IE tab showed Web Auth Redirect though...Changed again the web-auth secure web to enable and rebooted the WLC fixed the issue.
View 4 Replies View RelatedI have a cisco 5508 WLC that I have setup WebAuth on and trying to install the certificate on. I have generated the csr and gotten my cert from Verisign (X.509, server platform=apache). I have followed the instruction via the cisco documentation url...I found an error in uploading and find out how to encrypt mykey: url...
I am also having exactly the same issue with a certificate from Thawte. I followed the unchained guide and have tried both with and without a password in the initial step key generation step, requesting a new cert each time. As with Jeensernchew's issue there are no errors in OpenSSL but when uploading the cert to the WLC get the following error. [code] The WLC is running version 6.0.196.0. I am using OpenSSL 1.0.0 29 Mar 2010.
When I requested the cert from Thawte I was asked to specify the device type, I chose Cisco, but as all the work and conversion is being done by OpenSSL, should I have chosen differently? When I do this I can load the cert in the 5508, but the controller fails and doesn't allow that VLAN or config access to the wireless network. I am at a loss of why I can load and it not work. I have verified my hostname and password and those are good.
I have a guest wireless network setup on a 5508 WLC using 7.2.103.0 firmware. Under my guest WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected, "over-ride global config" as check marked, "web auth type" as "customized(downloaded), "login page" and "login failure page" as "login.html" selected.
I haveI have 4402 WLC's using 7.0.116.0 firmware throughout my company that anchor back to the 5508 for the guest network. The 4402 WLC have the guest network configured as WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected.
I would like to disable the HTTPS for the logon screen and I am not sure what steps need to be done for this. I researched and found the command "config network web-auth secureweb disable". I set the command on the 5508 only and rebooted. When I tested I got a blank webpage with "http://1.1.1.1/fs/customwebauth/login.html?switch_url=http://1.1.1.1/login.html" in the address bar and had no way of clicking the accept button to get to the Internet.
Everything works fine again if I enter "config network web-auth secureweb enable" and reboot. Do I need to run the "config network web-auth secureweb disable" command on all the 4402 WLC's that are anchored to the 5508? What could be breaking my login.html page while using only http?
I´m wondering if it`s possible to export the defualt web auth portal(web login page) via tftp to a computer from the Cisco WLC 5508 and then modify it and then import that customized portal to the WLC 5508?
View 6 Replies View RelatedI see I have 2.1.39.144146 but I don't see that version on the download page?
View 3 Replies View RelatedWhere do you turn this option off? i have looked under security and did not see any thing.
View 1 Replies View RelatedI have the following systems in place:
5508 WLC - 7.4.100.00
NAC Guest Server - 2.1.0
I have setup an SSID with external Webauth, which is pointing to the login page on the NAC.All works fine but I cannot use the logout page which is customized on the NAC. I always get the internal default logout.html of the WLC and I cannot customize that.Every customization which I have done to the logout.html (then uploaded it on the WLC) will not be recognized.Is there a way to customize that logout.html?
I've been asked to create 2 wireless networks for guest access. They are to be used by clients of 2 different companies and they have asked for the website of each company to automatically open as a landing page. e.g.
-WLAN1 - password is companyname1 - landing page = www.companyname1.com
-WLAN2 - password is companyname2 - landing page = www.companyname2.com
Is this possible with our 5508 WLC? I have googled it and can see that you can set a web auth page but I need different landing pages depending on which WLAN is connected to.
We have a centralized WLC with some branch office with AP's in Flexconnect Mode. The Wlans are configured to use Web Authentication (Landing Page). The Landing Page is Cisco Default.
We're experiencing some problem with Apple Devices, on some the Landing Page apperars on some not. The WLC Software is about 1 year old. On a XP machine the landing page doesn't appear too, but you can type in the address manually and it works.
Whats the best solution to include the Apple Devices successfully in the WLC Wireless World.
I have a 5508 WLC running 6.0.202.0. It functions as the Anchor Controller for the guest network. It sits in our Internet DMZ and is isolated from the rest of the network. It does not connect to AD, ACS, etc. The guest wireless WLAN is configured for Web Policy - Authentication. I have a customized login page. Credential management is done by WCS.
Users are connecting to the guest wireless network and entering their creds with no issues using mobile devices (iPad, etc). Then the mobile device goes to sleep / turns off and when they go to use it again, they have to type their creds in again. They dont like retyping their creds throughout the day.
good way mitigate the multiple logins? Something like a 'save password' option on the customized page?
I successfully converted an old 1231G to CAPWAPP. However, when I try to join it to a WLC5508 I receive the floowing errors. [code]
View 2 Replies View RelatedI have a Cisco 5508 running version 7.0.116.0. This controller hosts an open public wifi that requires users to accept a terms agreement via a Web-Passthrough setup that redirects them to the terms splash page. For most people this works without any issue. However, if a user has their homepage for their default browser set to a https site, such as [url]..., then they are never redirected to the terms splash page. The page will just spin and spin until finally they get a timeout error.
View 7 Replies View RelatedI have a 5508 WLC connected to 2950 Switch and the LAP 1262 connected to the same default VLAN. My AP's are able to join the controller since they are in the same broadcast domain but They are NOT able to download the image from WLC. When I am looking at the wireless TAB of WLC.. it says... Downloading Image.
what all needs to be done to make UP the APs. Also, Following is the error i am seeing at the AP.
*Apr 27 11:48:40.640: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.99:5246
*Apr 27 11:48:40.640: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
When a guest user first trys to access the "guest" WLAN, they are presented with a "certificate page" before the web athentication page / login is presented. The WLC forces an internal redirect to https://1.1.1.1 causing the certificate page to appear. Can this be bypassed? I am runiing 5508 with 7.0.220.0.
View 12 Replies View RelatedI started a download to a 5508 to upgrade to 7.2.110, but the connection across a vpn is slow and taking too long. Can I cancel the download w/o corrupting the current image and/or setup?I don't see a cancel button anywhere in the gui and don't want do it unless the controller will handle an incomplete download correctly.
View 5 Replies View RelatedWe recently did a forklift upgrade on our campus and installed 3502i's, 3502e's, and 11 5508 WLC's. Our students are complaining about slow connections in several areas of the campus.In our testing and basic trouble shooting our Apple laptops have no problems but our windows laptops are showing a very slow connection rates 264kbps downloand and 366kbps upload. The window device has current drivers installed.
View 14 Replies View RelatedI was using Document 100787 as a guide.
1. I have 1252 & 1142 AP's connected to the Wism (6.0.188.0 code)
2. FWSM I have a 4402 (6.0.188.0 ) appliance connected as my anchor.
3. ACS is ver 4.2
All of my wireless networks function as expected. I see the successful auth in ACS. I just built a new WPA2 network and set it up to use Splash screen redirect. It doesn't seem to matter what I do it just wont work. IE or Mozilla.Test 1 was to drop the users at the wism. There was no splash screen.There was no evidence of my url-redirect in the wireshark trace.Test 2 used the 4402 as my anchor point with the same results. In both cases the client was authenticated and was able to navigate the internet and other duties. The problem is apon opening the broswer there is no redirect.
I am trying to update my F5D7234-4 G Wireless Router - Firmware and I am told No known program will open this file. This file is part of a program. What do I do?
View 1 Replies View RelatedI saw a reference to release notes for firmware 1.1.0.9 (I think that was the number) for the RV110W but if I browse the firmware download page I only see 1.0.1.6 available for download. Is this available somewhere or am I confused and saw a reference to something else?
I have an installed RV110W at a client site that has to be rebooted about once a week since it stops allowing inbound access to mapped ports. For example, it stops forwarding connections on Port 25 to the client's e-mail server. I thought for a while there was a software issue with the e-mail server but after days of eliminating all other likely issues I rebooted the router and everything was fine. Now the problem recurs about once a week and rebooting the router always fixes it (this is week 3). Forwarding to ports 80, 443, and several others also stop working.
set the max download speed of torrent protocole by my router setup page ?My step father currently downloading with torrent and all the internet in the house is pretty slow so i will love to lower he speed so i can use my internet properly
View 5 Replies View RelatedCan't find WAG160N firmware upgrade download page on this site A few mounth ago it existed
View 3 Replies View RelatedI am configuring my 5508 WLCs with SW version 7.0.116.0. I configured a guest ssid with web-authentication enabled, but I cannot retrieve the login page on the controller. I configured the virtual interface with the addredd 1.1.1.1 SSID Layer 2 security: None SSID Layer 3 security: Web Policy enabled
I join the ssid with clients, receive the IP address correctly however when I try to open a web page, the login page does not appear. When I check the client status I see that it stuck in WEBAUTH_REQD state.