Cisco Wireless :: WLC 7.0 No Sufficient Privileges To Delete Rogue APs

Aug 7, 2012

I think this is a bug, but I wanted to check if others have the same problem. If we try to delete rogue AP's under MONITOR > Rogues with Remove Selected then we get a error message Authorization Failed. No sufficient privileges. At first sight, it looks like the AP's are gone, but if you click on the same menu again, they are still there.
 
My ACS admin user has role1=ALL. I even tried to set role1=MONITOR, then I don't get the message above, but it is stated that I can not delete known rogue AP's.

View 10 Replies


ADVERTISEMENT

Error - You Don't Have Sufficient Privileges To Configure Connection Properties

Mar 1, 2013

I have a HP G60 Series. Im trying to bridge connections with my xbox and wifi and i cant because it says "you don't have sufficient privileges to configure connection properties

View 1 Replies View Related

Cisco Switching/Routing :: Is SG300 52 Ports Sufficient For Network

Nov 8, 2011

I need the conception of the local network for my company. I have seen the sg300 switch that can be good for me (excuse my bad english, i am french). I have 12 servers (database + file servers) that i want to plug on the sg300 20 ports. I want to plug on it 3 switch sg300  52 ports that contains ipphone, desktops and  printers. (about 70 users)

View 4 Replies View Related

Cisco Wireless :: Grafs-S03 / WLC Containing One Of Its Own APs As A Rogue?

Aug 14, 2010

We have several WLC's in school sites all connected back to a central WCS (ver6) which is working fine so I am just trying to clear up a few small issues.At a couple of sites I am getting alarms on WCS as per example below which has me at a loss.WCS has detected one or more alarms of category AP and severity Critical in Virtual Domain rootfor the following items:AP 'grafs-S03' is being contained. This is due to rogue device spoofing AP 'grafs-S03' BSSID or targetting AP 'grafs-S03' BSSID. - Controller Name: grafs-wlc-01E-mail will be suppressed up to 30 minutes for these alarms.Then a minute later I get the following to say its no longer being contained.WCS has detected a change in one or more alarms of category AP and severity Critical in Virtual Domain root. The new severity of the following items is Clear:AP 'grafs-S03' with protocol '802.11b/g' on Controller '10.96.192.5' is no longer being contained. Service is restored. - Controller Name: grafs-wlc-01E-mail will be suppressed up to 30 minutes for these changes.

View 16 Replies View Related

Cisco Wireless :: 1242-AG Admin Status For Rogue AP

Aug 20, 2012

We have 1242-AG series AP which is configured in Rogue Detector mode. After adding this AP to WLC its showing Admin Status of AP as Down.
 
When i am trying to enable the Admin Status its giving me following error
 
" Admin status cannot be enabled for AP in Rogue Detector mode".

how to enable Admin Status for Rogue Detector AP.

View 4 Replies View Related

Cisco Wireless :: 5500 Detecting Rogue AP Messages In Syslog / Configuring WLC

May 9, 2013

I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan  controller 5500 controller with AP (aironet 3500). I want to detect for  rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to  detect this behavior.
 
Authorize AP's against AAA function to make sure that  all the AP's  registering to your WLC are authorized AP's of the  network.By  enabling  this feature, only those AP's whose mac-addresses are present  in the  authorization list, will be able to register to the WLC. url...
 
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it. url...the forum I have seen other talks about the same issue and saying that  if I have any APs in "Rogue Detection"  mode sitting on the trunk port   on the switch then  only, this AP will detect the  Rogue on Wired.

View 2 Replies View Related

Cisco Switching/Routing :: 1841 - Set Up Different Privileges On Router

Mar 7, 2012

We have a Cisco 1841 router that requires 2 levels of access, at the moment we have network admins logging in with a single username via SSH and with privilege 15 but we also need our helpdesk to login to run certain commands but not chaneg anything

View 4 Replies View Related

Cisco Wireless :: 5508 - How To Determine Geographic Location Of Rogue Access Point

Oct 31, 2012

I have the wireless controller 5508 and many AP1261 registered on site. It detects a lot of rogue access points around. I would like to find out geographic location of these rogue access points. Is it possible?

View 2 Replies View Related

Cisco Firewall :: How To Create Customized User In ASA5505 Having Certain Privileges

Feb 10, 2013

How can i create customized user in Cisco ASA 5505 having the following Privileges? note i dont have AAA server.User can only perform show running, ping, traceroute, show xlate. I have review one of the firewall configuration and found two type of password defined, what is the difference b/w enable and password?

View 2 Replies View Related

Cisco Routers :: Create Another Account With User Privileges In RV042 V3?

Jul 26, 2012

I am just wondering if it is possible to have two user accounts in Cisco RV042 V3 (Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18). User accounts to mean that one user can access the router with an administrative level access can do all the changes and management of the router's configurations and settings while another user can only do viewing of the system summary tab and connect and manage the simple configuration to connection to the ISP in both WANs, like setting up the connection type and release/renew the ip address for dynamic ip assigned by the ISP DHCP server.

View 1 Replies View Related

Cisco :: WLC 5508 Use TACACS To Authenticate Admins / With Maximum Privileges

Sep 23, 2012

I have an issue with two wlc 5508 in the same mobility group. We use TACACS to authenticate admins, with maximum privileges.
 
When I want to configure cleanair, or some security functions (such as ACL, or password policies), I have an error message saying that my privileges are not enough.When I use local account, it works well.
 
At the begining, I thought it was a TACACS issue, but I have the same problem with WCS and SNMP. Cleanair doesn't appears in config menu, and I have an error message for security function.

View 10 Replies View Related

Cisco Switching/Routing :: 2960 Radius Server Users Different Privileges

Jul 26, 2012

I have Cisco 2960 switches deployed in my environment along with radius server authentication. Now i need to assign some roles to particular users (shutdown port, description) so what i need to do for this task so not all users have same privileges.

View 1 Replies View Related

Servers :: Switch / Hub Sufficient To Connect All PC's To Modem To Connect To Internet?

Apr 12, 2011

I am in the process of opening an internet cafe. I dont know exactly what a pc server does on the network... or do I really need one? Is the switch/hub sufficent to connect all pcs to the moderm to connect to the internet?

View 1 Replies View Related

Cisco :: 5508 / Rogue AP Detection On WLC?

Apr 24, 2012

I have a 5508 controller with 70 AP's ( a mix of 1131 and 1142). On the Monitor tab I can see under the Rogue Summary numerous "Rogue AP's" as well as the clients associated to these AP's. There are no Rogue AP's on my wired network according to the report. My question is this: What actions should I take regarding these "Roague AP's"? Many of them appear to be just other AP's in the residential area near by. I know I can take action to classify them as Friendly or Malicious as well as Internal or External, but what benefit is there to doing this? Will taking these actions keep my AP's from scanning off channel for Rogues? I read that if a "Rogue AP" is not on the wired network that is really is not considered a threat. Any Cisco best practices regarding how to handle detected Rogue AP's ?

View 4 Replies View Related

Cisco :: How To Find Out If Rogue AP Is On LAN From WCS / WLC 5508

Mar 18, 2012

We have recently deployed a wlc5508 & some 40+ 3502i APs at the location.In the wlc I notice quite a few "rogue AP" listed with ssid's.
 
Is there a way within the wcs or wlc to determine better if any of these rogue AP are on my Lan?If I can locate the mac address of the ethernet port on the rogue AP I can track the port down on the appropriate switch & shut it down.

View 7 Replies View Related

Remove Rogue Router From Network?

Jan 25, 2011

I've been noticing a Belkin router on my network for a while now and just yesterday another Linksys router as join the party, causing havoc on my connection speed!

The strange thing is that I'm the only one seeing them through Norton on my laptop, all other computer on my home network is not detecting them. could this mean that someone is monitoring me? is possible? If I move permanently to Ubuntu linux would the problem go away? OR will they still be able to connect and monitor me?

View 6 Replies View Related

Cisco :: 1242 Rogue Detector Access Point

Mar 9, 2009

If you deploy a Cisco 1242 a/b/g access point as a rogue detector, can this be used for 802.11n wired detection as well.i.e Will the controller send the MAC addresses of the 802.11n clients and APs. url...

View 8 Replies View Related

How To Detect Rogue DHCP Server In Network

Feb 13, 2012

What tool can I use to accurately pin point a rogue dhcp server in our network?

View 1 Replies View Related

Rogue Network Cable Can't Connect Using Switch

Feb 19, 2012

I have an underground cable connecting a classroom to the main server.

If I plug any computer directly into the underground cable it connects to the server fine.

If I plug a switch into the cable, none of the computers connected to the switch gets an IP address from the server. When I try to assign manual IP addresses I also can't connect.

But when I use the same switch and plug it into the server using a shorter cable everything works.

View 5 Replies View Related

How To Delete Wireless Network

Aug 5, 2012

i created a new wireless network by going to network instrastructure and right clicking on pk5000z ap and configure. then set up a network pop up asking for 8 digit pin from the router label i typed the pin in. now that i made a new network the new network shows up instead of my old network.i cant connet to my old network even if i type it in manually. ive tried to delete the new network in manage wireless networks. but it still shows up.

View 5 Replies View Related

Cisco :: 2504 Configure Rogue Detector AP And Trunk Port?

Dec 14, 2012

I'm using a 2504 controller.  I dont have WCS.My questions are about the best way to configure a Rogue Detector AP.
 
In my lab environment I setup the WLC with 2 APs.  One AP was in local mode, and I put the other in Rogue Detector mode.The Rogue Detector AP was connected to a trunk port on my switch.  But the AP needed to get its IP address from the DHCP server running on the WLC.  So I set the native vlan of the trunk port to be the vlan on which the WLC management interface resides.  If the trunk port was not configured with a native vlan, the AP couldn't get an address through DHCP, nor could the AP communicate with the WLC.  This makes sense because untagged traffic on the trunk port will be delivered to the native vlan.  So I take it that the AP doesn't know how to tag frames.Everything looked like it was working ok.
 
So I connected an autonomous AP (to be used as the rogue), and associated a wireless client to it.  Sure enough it showed up on the WLC as a rogue AP, but it didn't say that it was connected on the wire.  From the rogue client I was able to successfully ping the management interface of the WLC.
But the WLC never actually reported the rogue AP as being connected to the wired network.So my questions are:
 
1. What is the correct configuration for the trunk port?  Should it not be configured with a native vlan?  If not, then I'm assuming the rogue detector AP will have to have a static IP address defined, and it would have to be told which vlan it's supposed to use to communicate with the WLC.
 
2.  Assuming there is a rogue client associated with the rogue AP, how long should it reasonably take before it is determined that the rogue AP is connected to the wired network?  I know this depends on if the rogue client is actually generating traffic, but in my lab environment I had the rogue client pinging the management interface of the WLC and still wasn't being picked up as an on-the-wire rogue.

View 4 Replies View Related

Cisco :: Detecting Rogue AP Messages In Syslog And Configuring WLC 5500

May 7, 2013

I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior. I'm doing this step.
 
Authorize AP's against AAA function to make sure that  all the AP's registering to your WLC are authorized AP's of the  network.By  enabling this feature, only those AP's whose mac-addresses are present  in the authorization list, will be able to register to the URL
 
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it.URL
 
NOTE: from the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection"  mode sitting on the trunk port  on the switch then  only, this AP will detect the  Rogue on Wired
 
I don't think i completely understand this statement, by sitting does it mean that it is passively sniffing coming in/out on trunk link?
 
Considering the above steps are accurate, after this will i be able to see rogue detection behavior in syslogs? What exactly would be the messages that would produce this behavior.

View 7 Replies View Related

Cisco Wireless :: How To Delete X509 Certificate On WLC

Oct 17, 2011

I had install third party CA cert and device cert into the WLC. I would like to ask is there any command can delete these certificate?

View 2 Replies View Related

Wireless :: How To Delete Unwanted Movies

Jan 17, 2013

I'm trying to delete downloaded movies off my laptop to free up some space-I tried uninstall but realize it isn't a program-we want to keep only a couple of movies-no success...

View 2 Replies View Related

Neighbor's Wireless Not Showing Up So Can't Delete It

Feb 26, 2012

I have a wireless PC laptop and a router that works fine. When I change rooms, there's competition from my neighbor's router and I want to remove it. When I "view wireless networks" I see their connection. When I go to "change the order of preferred networks" (hoping to delete it from there) it doesn't show up. If I go to "change advanced settings" I end up in the same place not showing the neighbor's wireless.

View 4 Replies View Related

Cisco :: 5508 Enable AP Mode To Rogue Detector From Details Page Of AP

May 28, 2012

(5508 WLC, 1142N APs).I understand if I enable the AP mode to Rogue Detector from the details page of the AP, the AP stops accepting requests and is now looking for rogue items on the wired network. Is this the same when I enable Rogue Location Discovery Protocol? Will I lose the wireless functionality of all of my APs on the controller?
 
Next question, when I look at the Rogue Summary on the Monitoring page I see three Adhoc Rogue devices. When I select the Detail link only one shows. I remember the other two were HP mutifuction devices with WIFI enabled but I cannot retrieve that information anymore.

View 9 Replies View Related

Broadband :: Unable To Connect To Internet After Removing Rogue Malware?

Dec 19, 2011

My computer was recently infected with the XP Antivirus 2012 rogue virus. I believe that it has been removed from my computer, but I am unable to connect to the internet. I am unable to obtain an IP address. The IP address is 00000 and the Submask is 0000. My operating system is Windows XP and I am using a High speed cable connection

View 5 Replies View Related

Linksys Wireless Router :: WRT54GL How To Delete Password

May 15, 2012

I have a Linksys Wireless-G WRT54GL v1.1 with password I don´t know.I wonder how can I delete the password? I tried resetting but still asks for the password!

View 4 Replies View Related

Linksys Wireless Router :: EA6500 - How To Delete Previous EA4500 From Cisco

Mar 30, 2013

I recently upgraded to the EA6500 from the EA4500, however under Linksys Smart Wifi i can still see "EA4500 (offline)".

View 1 Replies View Related

Linksys Wireless Router :: E4200 Delete All Files On NAS Drive

Aug 12, 2011

I moved to Comcast internet yesterday (from 3Mbps DSL), and the E4200 seems to be working well (although somewhere along the way it decided to delete all the files on the NAS drive...an issue for another day). On my laptops and wired PCs I'm now seeing 15-20Mbps down, and 4Mbps up. However, when I connect with my iPhone 3GS, I only see about 7.5Mbps down, and 4Mbps up using online speedtests.   I have tried messing with the router settings and resetting all the network settings on the iPhone but nothing changes.   I know my iPhone can handle more, because I get 15Mbps down when I visit family (they have a Netgear N300).  I can only conclude that my E4200 is the cause. 

View 6 Replies View Related

Cisco Switching/Routing :: 4503 Blocking Usage Of Duplicate Default Gateway IP By Rogue Attacker

May 16, 2012

We had a core switch (4503), distribution switches and access in our network and consists of many vlans. Almost all vlans uses DHCP Pools. But for few vlans DHCP is not yet configured. Recently one of the rogue user in vlan 1 gave the corresponding interface vlan ip of core switch (gateway) as his ip and caused a prolonged network outage for the vlan. Any way we are going to seggregate vlan 1 into different vlans, but before that we need a temporary plan to block such kinds of attack.What are the possible ways we can avoid the network outage problem even if a user gave the gateway ip to the machine?

View 3 Replies View Related

Cisco Wireless :: 6513 - How To Access Memory On WISM To Delete Old Boot Image

Sep 22, 2012

I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.

Midway through the transfer, the transfer stopped and I got this error on the log:

*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
 
How to access the memory on the wism to delete the old boot image?

View 1 Replies View Related

Linksys Wireless Router :: EA4500 Unable To Delete / Change Name Or Icon

Mar 6, 2013

I have a EA4500 that I get error 2315 when I try to Delete,change name,or icon. I did a 30/30/30 and everything worked great,24 hours later I was back to error 2315. I tried re-flashing the firmware, but that didn't work. I get the same problems when  I try using the Smart Wifi app. There are also times when I can not access the router using Smart Wifi unless I reboot the router when I get home. 

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved