Cisco Wireless :: Connecting IPad To Reflection In Laptop Via WLC 5508
Nov 18, 2012
recently we have purchased Reflection - an AirPlay mirroring software. Basically install Reflection in the laptop and you can view the screen of the iPad or iPhone via wireless network. we have tested in home wireless network no problem, but when connect to the cisco network, the iPad didn't recognize the REFLECTION installed in the laptop.
we are running WLC 5508, WLAP AP-1331AG, we can ping from laptop to the iPad laptop and ipad can access network without any issue. there is no any application port has been blocked between the client via wifi extra details for REFLECTION: [URL]
View 4 Replies
ADVERTISEMENT
Jan 5, 2013
Have WLC 5508 running 7.4 code; have wlan setup to allow access to internal network. Users on ipads should be able to connect to this wlan and authenticated via certificate instead of PSK. We have setup laptops that are part of domain to use internal CA for authentication to WLAN. Ipads are not part of domain so we are not able to use the same model, or can we use the same model for authentication?How to setup WLC to authenticate ipad users via certificate instead of PSK while connecting to the WLAN?
View 1 Replies
View Related
Jul 16, 2012
We are implementing a new corporate wireless network with Cisco 5508 WLC's and C3602I LWAP's. We are not running any RADIUS or EAP at the moment and are starting with WPA2 w/ AES with a pre-shared key to begin piloting. The issue we are having is iOS based devices (iPhone/iPad) do not seem to want to connect. We just get a could not join wireless network messages. We have had success with several Windows based laptops, my MacBook connects, as well as several different Android devices.Looking at the logs on the WLC I see these entries which correspond to the MAC address of my iPhone.
*apfMsConnTask_6: Jul 17 17:25:20.620: %APF-3-CHECK_SUPP_RATES_FAILED: apf_utils.c:376 Could not check supported rates. Missing Supported Rate. Length :0. Mobile MAC: 24:ab:81:92:4d:97.
View 28 Replies
View Related
Dec 1, 2012
We have a remote location with 1 LWAPP AP connecting to a 5508 WLC. We are doing 802.1x auth/wpa2 on 1 SSID for iPads to connect to. Now we want to simply connect a printer to print wireless using AirPrint from the iPads. The problem is how to get the printer connected to the wireless network specifically to the sane SSID? Will the printer need to support 802.1x or have the ability to do certificates? Is there a better way to do this.
View 5 Replies
View Related
Jul 27, 2012
on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
View 8 Replies
View Related
Sep 4, 2011
We have two SSID's Guest and Corp. We are using 5508 controllers.
The problem is that if an iPad user is connected to Guest SSID and then try to connect to Corp then it fails saying "Unable to connect to Corp". After 10-15 retires the same iPad connects successfully. The problem doesn't happen on windows PC. I have attached debug for one of the clients.
View 1 Replies
View Related
Mar 5, 2013
We have a centralized WLC with some branch office with AP's in Flexconnect Mode. The Wlans are configured to use Web Authentication (Landing Page). The Landing Page is Cisco Default.
We're experiencing some problem with Apple Devices, on some the Landing Page apperars on some not. The WLC Software is about 1 year old. On a XP machine the landing page doesn't appear too, but you can type in the address manually and it works.
Whats the best solution to include the Apple Devices successfully in the WLC Wireless World.
View 9 Replies
View Related
Apr 11, 2012
We find that some of the utilized iPads (iPad2, iOS 5) have a significant delay to connect to the WiFi after waking up.. though some of them show the WiFi-icon instantly after wake-up.. That is causing the crestron App on it to "malfunction", which is to say that it can't connect to it's server and goes back to home screen to allow re-connect..
WLC and LAPs using the latest software (7.2.103.0).. encryption is WPA2/PSK..
I changed the WLAN to use 802.11g only.. changed Beacon-Time.. changed encyption.. changed WMM settings..Alas, the iPads that expose this behaviour do not show any difference with the changes..
View 3 Replies
View Related
Jan 18, 2012
I have an ipad that is not able to connect to a 1142 Autonomous AP. This AP was originally a light weight AP and then downgraded to autonomous.A strange thing i see is that the AP shows me only two radios. 802.11 N(2.4 GHZ) and 802.11 N(5 GHZ). I suspected the AP not to support the b/g networks. i then downloaded the most recent software but i still cannot get it to connect and on the AP's GUI i only see the above two mentionned radios. i tried to connect to two SSID's. one using WPA2 and another with open authentication and no security.but this does not work. Is it possible that some 1142 do not support b/g networks?
View 21 Replies
View Related
Dec 28, 2012
When trying to connect my ipad to my windows wireless network it asks for a passwordIs this the same thing as my network key?
View 4 Replies
View Related
Jun 15, 2011
IPods and IPads to connect to stand alone AP1131? My scenario is as follows:
There is a section of a campus that is covered by 14 stand alone AP1131 were I experience the problem. The security parameters are: 802.1x, wpa enterprise, tkip
The other section is under WLC also AP1131 but in this case in WLANs/Scurity/Leyer 2 I checked boxes:
WPA Policy, WPA Encryption TKIP
WPA2 Policy, WPA2 Encryption AES
Auth Key Mgmt 802.1x
Wonder if the fact that I chose WPA2, AES makes a difference with stand alone mode? Anyways I tried configuring AES in stand alone APs and it didn't make a difference since I could not connect either.
View 9 Replies
View Related
Aug 27, 2011
I have an E4200 wireless router which is connected via USB to my Canon MX 308 printer. I am able to print from Windows computers that are connected to this router (via WiFi of course). My iPad 2.0 is able to connect to the internet via the router. However I am not able to print content from my iPad via the E4200 router (via Wifi using Cisco Connect software).
View 1 Replies
View Related
Mar 5, 2012
Have set up Router OK. Created Flashdrive EZ
How do I connect my IPAD now to WiFi since there is no USB port on my Ipad??
View 1 Replies
View Related
Dec 23, 2012
Region : India
Model : TD-W8951ND
Hardware Version : V4
ISP : MTNL
I m using TD-W8951ND wifi router with MTNL connection. The LAN connection with PC works just fine but i m not able to connect my iphone or ipad with the router. I have reset the router many times and also retored my iphone but still no luck. Pl tell me what are the settings needed for wifi connections.. Currently i have set the wireless mode to 802.11 b+g+n. Setting it to just 802.11 b sometimes connects with the iphone but never with ipad.
View 6 Replies
View Related
May 22, 2013
I´m trying to connect them to my WLAN, for throubleshoot I create a new WLAN with WPA2-TKIP and a PSK, the devices didin´t connect to the WLAN.I also change the security to WPA2-AES with TKIP, it didn´t work too.
My best choice was to disable every security configuration in order to began the throubleshooting from zero, but even with no Layer 2 and 3 security, the devices didn´t connect to my Test WLAN.
I´m using a AIR-CT2504-K9 WLC with two AIR-CAP3502I-A-K9 AP, all the PCs and other brand cellphones and tablets work well.
Also I have a SOHO router on the office, and the IPad connect without a problem with that WLAN, but I need them to connect to my Cisco AP.
View 7 Replies
View Related
Oct 21, 2010
after i had to replace my old router from lynksis for the wrt110, everything works except for the ipod touch and the ipad. what could be the issue?
View 8 Replies
View Related
Aug 8, 2011
I have 1 WLC AIR-CT5008-K9 version 7.0.98.0. with iPads connected to a WLAN with [(WPA+WPA2)(AuthPSK)].and have constant disconnections. But the Laptops do not have problems.
View 5 Replies
View Related
Feb 28, 2011
Using wireless PEAP via a 5508 controller and a verisign cert on ACS 4.1,The iPad still wants me to verify the cert even though it is a trusted CA.
View 2 Replies
View Related
Nov 9, 2011
we recently upgraded our home router and have been having trouble ever since. Our old router was a Netgear one, so we bought a newer netgear model. Since installing the new one we can not get my daughters laptop, an iPad and ipods to work on the wifi. My computer is wired into the router and works fine, it is just the wireless. All of these things worked perfectly using our old netgear wirelss modem and all of them can find the wireless network on their list of available networks, they all say that they are connected with a good signal, but when they try to browse the internet or check emails, it comes up saying not connected to the internet. We even bought a range extender because we thought the signal might not be strong enough between the new router and my daughters bedroom which are at opposite ends of the house and on different floors, but it made no difference and wasn't a problem before.
Anyway, the router we bought is a Netgear N150 wireless modem router DGN1000, the cables are plugged in to ports 1 and 4 ( there is only 1,2,3 and 4 to choose from). The extender is a Netgear universal range extender WN2000RPT
I have tried turning it all off and back on again, have uninstalled it and reinstalled it, but still nothing. Daughters laptop uses Vista and she has McAfee security. Exactly as it has always been and has worked fine using our old wireless router, just not this new one.
View 3 Replies
View Related
Jun 3, 2013
I cannot get my belkin n150 wireless router to connect to my laptop or ipad - wireless connection was working but stopped - so i attempted to re-configure the ip protocols on the router using the 198.168.2.1/ password - changed the ip setting on the belkin page but did not reset or set address (DHCP).
View 1 Replies
View Related
Mar 26, 2013
I recently had a 5508 controller installed and configured for a corporate network as well as internet only guest access. Users authenticate via 802.1X key management on the corporate network and web authentication via guest. This works fine, however, I've run into a problem. We also use iPads for inspections and the inspection site is housed internally. I've had a network admin create an exception in the firewall that will allow connection to the internal sites from the guest network, however, it does not function. I did find that if I connect an iPad to the corporate wireless network I'm able to download the necessary certificate to the device but that only works if I use my login information which is not something I am interested in doing. Is it possible to enable another authentication for the corporate network without breaking the functionality of the existing 802.1X authentication? What could possibly be the cause on the guest network not allowing connectivity to the internal sites, even though the exception has been created?
View 3 Replies
View Related
Nov 20, 2012
I'm using PfSense 2.0.1. What im trying to do is connect to a game server I have running here in my house. I can connect to it locally with 192.168.8.6 no problem. I have it port forward correctly so that the rest of the world can connect to it via my WAN ip address. The problem comes is I want to be able to connect to it with my WAN address so that if someone decides to follow me STEAM will show my WAN address not my internal IP address of the server im connected to. I have "Disable NAT Reflection for port forwards" UNCHECKED which is what I am supposed to do according to documentation from PfSEnse. But it still doesn't seem to work.
View 5 Replies
View Related
Aug 19, 2011
I am looking to purchase the RV220W router. I am interested to know if I can use the iPhone/iPad to create a VPN connection to this router.I have seen a lot of conflicting information about this so I am looking for a confirmation.
View 15 Replies
View Related
Sep 5, 2008
I have a linksys system WRT54G at home. I had no problems with the Linksys router until about a month ago when I decided to make it a secure network. I run three computers of the wireless router (1 desktp and 2 laptops) Since making the wireless network secure I can not connect with my business laptop IBM Thinkpad X40, but thother e computers work just fine.
View 8 Replies
View Related
Apr 18, 2011
I have ASA 5520 running ver 8.3.(2)8 and configured for AnyConnect VPN. While testing for iPads and iPhones we noticed that on connecting it disconnects few times before finally connecting. These are the messages logged in the ASA.I don't see authenticatio as an issue. Results are better with wifi compared to 3G. [Code]
View 1 Replies
View Related
May 2, 2012
I am having problems connecting an 891w to a WLC, is it possible to have to separate vlans, one for the Lan ports and another for the AP module.
I do not want the AP part of the 891w in autonomous mode. The WAN port of the router will be connected to a DSL type service.
Is there a guide or something to get a 891W to connect to the WLC?
I would like to have users on a data vlan (vlan1) connecting to the network like a normal router, then the AP module to connect to the WLC via a different IP probably vlan 2
On the WLC itself i do not see any attempts in the logging.
View 10 Replies
View Related
May 23, 2011
I m using 3G USB modem with my laptop. i also have ipad with wifi. my question is how to use internet on my ipad through laptop wifi & 3G USB modem?
View 1 Replies
View Related
Aug 6, 2012
question in regards to the deployment of a new WLC and new LAPs,I have configured and connected a 5508 WLC and 3500 series LAP.LAG is enabled in the WLC and successfully connected to the neighboring switch (using etherchannel) and to the network.
The port-channel port is set to trunk mode obviously and certain vlan ids are currently allowed (3-5)
The management interface has this IP address 192.168.5.250/24
I created a WLAN with WLAN ID 3, Interface set to Management and say SSID test1
I have connected a new LAP to the network, which switchport interface is set to access mode and assigned with vlan id 3. The LAP is able to join the WLC successfully with an IP address, such as, 192.168.3.100 (assigned via DHCP).
When I try connecting a mobile client to the wireless LAN, it can successfully detect and connect to the WLAN, created in the WLC (test1) however it gets an IP address by DHCP, in the 192.168.5.0/24 network, which is the IP range of the management interface's IP address.
What can I do to get the clients connecting on network 192.168.3.0/24? I thought this would be the case since I allocated the WLAN Id of 3 in the WLAN test1 configuration and since the LAP switchport is set to access mode with vlan ID 3.
View 3 Replies
View Related
Aug 6, 2012
I have a wlc 5508 and I'd like to setup a network for visitors. They will connect to the WLAN, enter a password and then automatically get redirected to an external website. I understand the wlc 5508 supports this but I'm struggling to find out how to set this up I assume this can be done without having to customise webauth bundles?
View 2 Replies
View Related
Jun 2, 2013
We have a 5508 with 7.4.100.0 vor Internal APs and OEAPs. till now every thing is ok. Now we have to connect an AP (local) in a remote office, connected to the WLC by a VPN Tunnel. The problem is that the AP in the remote office uses the NAT Address to connect to the WLC, so the traffic goes over the Internet, not trough the VPN Tunnel. On the controller I have the following setting:
AP Discovery - NAT IP Only ................. Disabled
On the AP:
AP Link Latency.................................. Disabled
How to force the AP to use the internal IP Address of the WLC?
View 7 Replies
View Related
Aug 26, 2012
I'm working on migrating autonomous WAPs to lightweight mode in a WLC 5508. Some of the older WAPs are being decommissioned at the same time.
One issue I have found is that after replacing an old WAP in autonomous mode with a new WAP (3502); some clients near the coverage of this new LWAPP are now connecting to another WAP in autonomous mode that has not been converted or replaced yet; but that is located quite far away from where these clients are, actually two floors down. Users on these clients have reported wifi dropouts, which is obvious due to the distance where the old WAP is. A workaround that seems to work is removing the wifi profiles in the client machines and recreating them again, which is not a good solution for all of the wifi profiles we have in place. At this point of time we still need to have the older WAPs until they are all replaced.
How can I get clients connecting to a LWAPP that is closer to their location? I'm wondering what causes those clients to look for an existing older WAP rather than connecting to the new LWAPP, which is broadcasting the same SSID closer to where they aree. Bear in mind that the new LWAPP is working fine and has live sessions working just fine.
View 5 Replies
View Related
Aug 4, 2012
I have an issue with my home network that is really stressing me out now. I have a Thomson TG585 v8 router that my laptop, iPad and iPhone connect to no problem but my iPad/iPhone won't talk to my laptop.. I want to be able to use my iPad to remote in to my laptop to watch movies etc. Network sharing is on the laptop and I've checked that all devices are on the same network..I can't ping the iPad or iPhone from the laptop either.
View 9 Replies
View Related
Mar 25, 2013
My laptop, windows 7, is telling me there are no connections available. My iPad and phone are connected. I've removed my wifi network and replaced it, I've restarted my laptop, I've deleted other networks.
View 10 Replies
View Related
