Cisco Wireless :: Perform Site Survey With Aironet 1041N Access Point?

Jul 15, 2012

We are in need to perform a site survey with the Aironet 1041N Access Point.
 
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
 
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?

View 2 Replies


ADVERTISEMENT

Cisco Wireless :: Aironet AP-1041N Setting To Have Access Point Broadcast Multiple SSIDs

Jan 17, 2013

I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?

View 1 Replies View Related

Cisco Wireless :: Setting Up Aironet 1552EU Used For Site Survey Without A WLC?

Jan 22, 2013

I am wanting to use a Cisco Aironet 1552EU to use on a site survey for a future deployment and I need to know if it is possible to configure the AP to broadcast an SSID so that my team can search for that SSID and view the signal strength throughout the site. Is a WLC required to set the SSID or is there an SSID that will be broadcast by default that we can try to connect to?

View 1 Replies View Related

Cisco Wireless :: Aironet 1041N Standalone Access Points Setup Information

Jul 19, 2012

I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.

The reason why I'm writing is because I have a few questions to clarify.  
 
1) What is the best position for better signal, top side wall or corner ceiling?
 
2) How many client mac address filtering  can i do per access point?
 
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.

4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)

5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?

6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?

7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.

8) Can CCp software be used in these access points?

View 9 Replies View Related

Cisco Wireless :: 2600 And 3600 Access Points Site Survey

Oct 12, 2012

I know that the deployment guide for 2600/3600 access points states that if you have surveyed for a 3600 deployment, you don't need to survey again for a 2600 deployment. As the the 3600 is the higher specification model, is it safe to assume the reverse? I.e. a site survey carried out using 2600 access points is valid for a 3600 deployment, or is this too simplistic?          

View 5 Replies View Related

Cisco Infrastructure :: 1041n Access Point Performance

Aug 24, 2012

I purchased a new ap1041n access point. It's the first Cisco I've tried to configure in a long time. I'm trying to get the 802.11n working but it seems to be stuck in 802.11G since I can only get it to go up to 36mb. The radio says its running in mixed mode and I can't figure out if that means b/g or b/g/n. I ran the Express Setup and it didn't seem to work.

View 5 Replies View Related

Cisco Wireless :: Enable N Speeds On Aironet 1041N?

Apr 4, 2012

how to enable wireless N speeds on this access point? It's operating in mixed mode via PoE. If I go into network interfaces -> Radio0-802.11N --> Settings, the highest data rate is only 54 mbps. Can N speeds be acheived in mix mode? Also, I thought this access point is dual-band, but I'm only seeing the one radio, is that normal? (see attached image)

View 9 Replies View Related

Cisco Wireless :: Site Survey With AP3500i

Jul 18, 2011

I have a question about sitesurveying with ap3500's, I'm going to deploy a wireless network in a new building, i have a company that normaly does my site surveys.

I normally provide them with some AP's configured with a designated ssid and local power modes set to 50%, however this does not seem possible with the new 3500i's i'm willing to use, for there is no IOS image available for it. I dont have any network connectivity yet in this new building, so i cannot f.i place them in a separate ap-group and assign a dedicated wlan to them.

View 7 Replies View Related

Cisco Wireless :: Site Survey Client On AP 1200?

Dec 13, 2002

Is there any detailed documentation on the Site Survey Client mode on the AP 1200?When using this mode I cannot see any indication that it has associated withthe root AP.  I would like to be able to pass traffic from the ethernet port to the root AP VIA the AP in client mode.  The Ap in client mode shows the radio in blocking when in client mode, is this normal?  Is there a way to manually change this to forwarding mode?

View 4 Replies View Related

Cisco Wireless :: Using 3602e With WSSI For Site Survey

Mar 27, 2013

How the full functionality of the Wireless Security and Spectrum Intelligence module is supported in autonomous mode for site survey use, or is a WSC required?
 
I'm wondering whether we need to invest in more survey/ spectrum analysis kit or could just use a 3602e with WSSI and the inbuilt Spectrum Expert?

View 6 Replies View Related

Cisco :: 3500 AP For Site Survey?

Dec 7, 2011

Has any tried using a 3500 CleanAir AP as a site survey tool? Could you set it up in multiple locations temporarily and gather interference data and analize through WCS? This would use the 3500 AP like you would the Spectrum Expert product.

View 7 Replies View Related

Aironet AIR-AP1252G-A-K9 - Wireless Access Point

Mar 19, 2011

I just picked up a Cisco Aironet AIR-AP1252G-A-K9 Wireless Access Point to mess around with at home and learn IOS.

The unit didn't come with a power adapter or any accessories. Just the bare AP. Does this AP need a controller to work? Can I use it as a standalone AP?

View 2 Replies View Related

D-Link DCS-942L :: Missing SSID On Site Survey

Apr 9, 2013

I've been trying to connect two DCS-942L to some netgear WNHD3004 (wireless access points a/n WPA2 personal) that I use as access point but I can't find them in the site survey (advanced settings then wireless setup in the camera page).I think I could set manually the network name, security mode and key but since I'm working remotly on these camera, I'm pretty sure it won't work and I'll loose connection (actually they are connected to other access points and work ok).An ipad and macbook pro is able to see and connect to these access points so I don't think they are the problem.I've updated the camera to the latest firmware (1.12 build 1608 agent version : 2.0.15-b11)

View 2 Replies View Related

Cisco Wireless :: Aironet 1130AG - Login To Wi-Fi Access Point?

Oct 13, 2010

I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.

View 3 Replies View Related

Cisco Wireless :: Aironet 1040 Access Point Managing

May 22, 2012

We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.

View 5 Replies View Related

Cisco Wireless :: Aironet 1310 - Outdoor Access Point

Sep 13, 2012

I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
 
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it.  I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS.  I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?

View 1 Replies View Related

Cisco Wireless :: Setting Up Aironet 1040 Access Point

Mar 13, 2013

I'm working on setting up an Aironet 1040 Wireless Access Point for my company.  It's my first time setting up something like this, and I've run into a bit of trouble.
 
I created my first SSID easily enough, following the manual and guides online.  I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great.  However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
 
I created VLAN 2, and then another SSID which I linked here.  I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager.  I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'.  I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.

View 4 Replies View Related

Cisco Wireless :: Aironet 1262N - Access Point Behind Non-Root Bridge?

Apr 9, 2012

I want to connect two buildings. Let's call them Building A (main) and Building B.
 
 „A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
  
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
 
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
 
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
  
My Questions:
 
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?

2. How Do I tell AP03 that it should use AP02 as a gateway to building A?

View 2 Replies View Related

Cisco Wireless :: 1242AG / Maximum Associations In Aironet Access Point?

Feb 12, 2011

I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.

Questions :

1.    What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?

2.       If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point

3.       I there a simulator tool that can be used to simulate multiple wireless connections to an AP

4.       Have anyone tested so many users connected to 1 Access point ?

View 7 Replies View Related

Cisco Wireless :: Aironet 1260 Access Point Work Without Controller??

Dec 1, 2010

I would like to buy Cisco  Aironet 1260 Access Points, i just want to use them independantly so   i want to know do they work without the Wireless LAN Controller? or i  have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.

View 9 Replies View Related

Cisco Wireless :: Aironet 2602e Configuration As Standalone Access Point

Mar 19, 2013

I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.

View 2 Replies View Related

Cisco Wireless :: Change IP Address Of Aironet 1200 Series Access Point

Dec 30, 2012

we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.

View 17 Replies View Related

Cisco Wireless :: Aironet 1140s - How To Connect Repeater To Specific Access Point

Feb 12, 2013

In our office, we have 3 Cisco Aironet 1140s and they are configured as follows: 

* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
 
how to have the Repeater connect to Access Point A only?

View 3 Replies View Related

Cisco Wireless :: Aironet 1310 - Infrastructure Access Point Unreachable For Management

Sep 16, 2010

We have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings.  One went south on us & we placed it.  Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP.  Now, we can't connect or even ping either AP.  And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them.  I'm attaching the configuration.  Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?

View 3 Replies View Related

Cisco Wireless :: Aironet 1310G - Point To Point Bridge

Oct 14, 2012

Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".

View 16 Replies View Related

Cisco :: Configuring Aironet 1100 Access Point?

Dec 22, 2011

I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?

View 8 Replies View Related

Cisco :: Configure Aironet 1040 Access Point?

Oct 27, 2011

I am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below

%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
 
and the ssid is not getting broadcasted. kindly let me what could be the cause.
 
[code]....

View 3 Replies View Related

Home Network :: Set Up Access Point Aironet 1040 Cisco?

Nov 23, 2012

how i can set up access point aironet 1040 cisco?

View 2 Replies View Related

Cisco :: 1130 - Aironet Access Point Not Able To Connect By User

Jun 12, 2011

I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.

Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
[Code] .....

View 0 Replies View Related

Cisco :: Setting Up Aironet 3500 Series Access Point

Nov 21, 2012

links with information / guidelines for the initial setup for this Access Point?

View 7 Replies View Related

Cisco :: Change WPA2 Key On Aironet 1231g Access Point?

Mar 22, 2012

I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?

View 4 Replies View Related

Aironet 1121 - Client Isolation On 1 SSID In Cisco Access Point

Feb 2, 2011

i've been looking for a way to isolate clients on a Cisco Aironet 1121 on a certain SSID, and i cant find anything, tried pretty much everything i coudl remember, but since im no expert on Cisco wireless.

Quote:

Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.

[Code].....

View 3 Replies View Related

Cisco Switching/Routing :: Access Point Aironet 1040 Configuration - Not Getting 802.11n To Work?

Jun 25, 2012

I can't figure out how to get the config right for the 802.11n channel to work.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved