Cisco :: Wlc 4402 4.2.61 Unable To Add Mac Entry To Database

Apr 30, 2012

When I try to add new MAC entrys to the WLC I get the following message unable to add mac entry to database, reached  max size the problem is when I look at the stats there is only 386 MAC entry and the databse size was set to 1024 entry..The work around was  to increase the size of the database  to 2048.Is there any why to clean up the database?

View 2 Replies


ADVERTISEMENT

Cisco :: 4402 WLC - Syslog Message / Unable To Allot AP Entry In Database

Feb 23, 2011

Receiving the following syslog message from a 4402 WLC:
%CAPWAP-3-AP_DB_ALLOC: capwap_ac_db.c:145

Unable to allot AP entry in database. We receive this message about once a minute on average. I can't find any documentation saying what it is. It looks like a database error, which makes think it might be a memory issue or an issue with having too many AP's on the WLC. However, that controller has less than 30 AP's on it.

View 3 Replies View Related

Cisco Wireless :: WLC 4400 - Unable To Find AP Entry In Database / Could Not Process Statistics Info

Jun 24, 2012

Six month ago I installed and configured a wireless mesh with the equipment named. From two weeks ago one AP (MAP) restarts every day. In Wireless Lan Controller appears this logs:
 
"Unable to find AP entry in the database, could not process statistics information"

View 2 Replies View Related

Cisco :: No Entry In DHCP Snooping Database?

Apr 29, 2011

an attacker have configured his PC with an static IP address but there is no such entry configured statically in switch, neither in DHCP snooping database.now when he want to generate traffic will switch block him? because there is no entry of his PC in the switch database.

View 2 Replies View Related

Cisco :: 4402 / Wlc Max Database Size?

Jun 28, 2011

I have a 4402 being used as a dmz anchor and we use WCS to allow our Helpdesk to create lobby ambassador accounts. Recently they have been getting error messages when attempting to create accounts. I am seeing the database maxxed out at 2048. The docs state database entries are made up of mac filters(don't use)..ap mic/ssc(don't use)..Dynamic interfaces(minimal) management users(2) local netusers (100 approx)..and excluded clients(none). So the numbers don't add up.I am on 4.2.61.0 code.. I will say also that WCS shows alot more netuser accounts than my anchor does but no where the numbers to max out the database. Is there some other criteria that hits against the datasbase number??  And what can I do on the WCS to insure it si synch'd up against the dmz anchor other than a audit..

View 3 Replies View Related

Cisco :: WLC 5508 And 4402 - Mac Address Filtering Database

Mar 27, 2012

l have implemented mac filtering auth on my wireless network, l have 2 WLC ( 1 WLC 5508 and 1 WLC 4402, and I wonder if you can migrate the mac address database of a WLC to another and how can l do this.

View 4 Replies View Related

Cisco :: 4402 To Script Additions To Local MAC Filter Database

Aug 24, 2011

We have implemented a local MAC address filter database on a WLC 4402.  Right now, management access is restricted to a select few administrators.  We would like to extend the ability of our PC services group to add MAC entries to this database via a script (avoiding the necessity to create Read/Write management user accounts).  Is this possible?  Is there a better way to accomplish this objective ?

View 7 Replies View Related

Cisco :: LMS 4.2 Error - Unable To Connect To Database

Sep 12, 2012

I have the following message in my CiscoPrime LMS 4.2.2 home portal: Discrepancies: Unable to connect to Data base. Probable Cause:  ANIDbEngine process may be down.

View 4 Replies View Related

Cisco Switching/Routing :: 3560 - Unable To See Entry For Switch

Oct 30, 2011

I have configured a new switch 3560 switch and connected to 4500 switch and formed a trunk connectivity.Now the issue i am facing is when i do a SH CDP NEIGHBOUR from 3560 switch i am able so see 4500 swries switch but at the same time when i do SH CDP NEIGHBOUR form 4500 series switch i am not able to see the entry for 3560 switch.But i am able to telnet the new switch with out any issues

View 11 Replies View Related

Cisco Switching/Routing :: 2811 - Error Unable To Find Entry For VLAN (1)

Aug 23, 2009

Aug 24 11:32:16.275 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to down
Aug 24 11:32:36.827 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to up
Aug 24 11:35:23.854 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/2, changed state to down
Aug 24 11:35:24.854 AEST: %LINK-3-UPDOWN: Interface FastEthernet0/1/2, changed state to downesw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)(code)

When the above problem happens, as work-around, we delete VLAN.DAT file on the Compact Flash of this 2811 router and recopy the VLAN>DAT  file back to teh Compact Flash.
 
Then it runs for a few weeks and the same problem happened.
 
Then we put a new Compact Flash and recopied VLAN.DAT to new CF and it ran for 3 weeks and same problem started again.
 
Could be 2811 router motherboard? This customer has thousands of these 2811 routers in identical setups and this is the only router that is having this problem. 

View 6 Replies View Related

Cisco :: 4402 - Unable To Setup WLC For LDAP

Apr 26, 2011

I'm trying to setup WLC for LDAP to authenticate the users. I have all the components required according to cisco's document. WLC4402, LAP1142N, 2008 AD serving as LDAP.
 
I'm configuring according to the document and also trying same settings from other users on this forum who (seems to) have got the WLC-LDAP up and working. My problem is that I'm receiving the below debug message on the controller and there is nothing on the internet on this error:
 
*LDAP DB Task 1: Apr 28 10:05:35.903: LDAP server 1 changed state to IDLE*emWeb: Apr 28 10:09:21.046: aaaLdapServerStateSet [1] changed state to 'DISABLED'.*emWeb: Apr 28 10:09:21.046: aaaLdapServerStateSet [1] changed state to 'ENABLED'.*LDAP DB Task 1: Apr 28 10:09:21.052: ldapTask [1] received msg 'CLOSE' (4) in state 'IDLE' (1)*LDAP DB Task 1: Apr 28 10:09:21.055: ldapClose [1] called lcapi_close (rc = 1008 - Invalid client handle)*LDAP DB Task 1: Apr 28 10:09:21.055: LDAP server 1 changed state to IDLE
  
I'm getting this error regardless of the authentication type, any username and attributes. So it makes me think WLC is not even trying to bind to LDAP. If the error was invalid credentials or something mismatch or something, it gives me some information to base my troubelshooting but I just can't find information on this (rc = 1008 - Invalid client handle) message.

View 3 Replies View Related

Cisco :: 4402 - Unable To Access WLC From Wireless?

Nov 15, 2011

We have a WLC 4402, with interface Management, AP-Manager, and only the ap-manager interface is enabled for dynamic AP Management, how can i enable the dynamic AP Management for management interface also. Because i couldn't access WLC from via wireless, only able to access it via wired.

View 15 Replies View Related

Cisco :: 4402 Unable To Access Service-port

Dec 9, 2012

I have a 4402 and recently I have not been able to access the device via the service-port interface. The service-port has an IP Address and it is connected to an access port in the Vlan which I am coming from, however it cannot even ping it's gateway, which as mentioned is within the same network. When I am at the console of the controller I can ping the service-port interface IP that I have assigned, just nothing else.

View 4 Replies View Related

Cisco AAA/Identity/Nac :: WLC 4402 Unable To Authenticate Correctly With ACS 5.2

Jun 8, 2011

For unknown reason I cannot get WLC to authenticate correctly with ACS 5.2. it's very strange in the sense that when I checked the log. ACS authenticates and authorized the WLC 4402 but I cannot log to the WLC. login screen appeared, if I typed user name it jumped to Controller> user: password:
 
No matter what I typed (internal or external users) nothing seems to work. This is my frustration, I have no problem authenticating routers and switches except WLC 4402.

View 8 Replies View Related

Cisco Wireless :: Unable To Get 4402 And 2504 To Pair In Mobility

Jun 12, 2013

I am unable to get my 4402 and 2504 to pair in mobility, I made short video to explain my issues.also do not worry there is no propritary information in this video, I am working on a lab that does not mirror any production networks.

View 6 Replies View Related

Cisco Wireless :: Unable To Upgrade Lan Controller 4402 Firmware

Mar 1, 2012

I am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller.  i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230  and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
 
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and  the tftp client to no avail
 
the error i get on the wlc is Code file transfer failed - Error while writing output file

View 5 Replies View Related

Cisco Firewall :: ASA5510 No ARP Entry?

Jan 26, 2012

I have a requirement to NAT a spare address on the same subnet range as one of the firewall interface - however, because this is not allocated to a physical interface, there is no mac entry in the arp cache. the other end of the link from the firewall is connected to a router which has no idea how to reach this "virtual address" - again because there is no entry in the arp cache I have tried to put a static arp entry into the firewall but this doesn't appear to work either. Should I be using a mac address form a physical interface or can I create a dummy mac for this - If the router can't see the ip address, then users will not be able to target this address - so that the firewall can NAT to the real outside address.I have tried routes to null0 on the router and static arp entries on both devices but the user just times when trying to connect to 10.2.7.11 (nat to 10.2.32.11)

View 6 Replies View Related

Cisco WAN :: 2 BGP Routers With 1 NAT Entry 881 Configuration

Sep 26, 2012

I am trying to split traffic entering from the web for servers so everything goes over the ADSL link but time sensitive information such as Sharepoint (TCP80) go direct over the ESHDSL link, now the problem is traffic that enters through the ESHDSL hits the server, the server replies out of its default gateway which is the ADSL which doesnt know what to do since it does not have a NAT entry for its return path.
 
How can I make it so traffic can enter one router and exit the other?
 
The two routers have HSRP to provide fail over between the two, and BGP is setup so one BGP route goes ESHDSL-ADSL and the other ADSL-ESHDSL

The routers are a 877M-SEC-K9 and a 881-SEC-K9

View 1 Replies View Related

Hostname Entry Against Public IP?

Sep 5, 2012

We have one business application, accessed across GCC region by having a single entry with individual computer hosts file, ie123.123.155.116 myappl.mycompany.com and other than Bahrain, all countries are able to successfully resolve the hostname (application only works against hostname (Oracle EBS)) against this entry with the hosts file. Now, prior contacting the ISP in Bahrain (where internet is regulated due to the current political situations) we need to know whether anything could be done from our end to resolve this issue.

View 2 Replies View Related

Cisco :: Use DNS Entry In Extended ACL Instead Of IP Address Range?

Sep 1, 2011

Is it possible to use a DNS entry in an extended ACL instead of an IP address range?

View 2 Replies View Related

Cisco Wireless :: WAP200 And Entry For Primary Dns Cannot Be 0 And 255

Nov 16, 2011

I have a wap200 with a static ipaddress e.g. 192.168.249.205/24 (it is for management and is in vlan 1). Firmware of the wap is 2.0.4.0. No gw and no dns. (they are not necessary) I export the config . I have a second wap200 and import the config.bin to the new wap. ThenI like to change the static address and the name of the new wap, but - and this is the problem - it asks me to fill out the dns (the address for primary dns cannot be 0 and 255), but I absolutely don't want that because there is no dns or gw (management only). And if I fill it out I cannot go the the internet with the wap.

So I also have some other wap200 where I could import the config.bin and change the static ip without giving a dns (firmware 2.0.1.0). can I go back to a previous firmware (Europe) and where can I find it. Looked for it, but seeing only the last one 2.0.4.0 etsi.Or is there another method to skip the dns with a static ipaddress?

View 3 Replies View Related

Cisco WAN :: Can't Create NAT Entry For A Range Of Ports With CCP On 877

Mar 17, 2011

Using CCP I am trying to create a NAT entry for a range of ports. CCP window for a new NAT has only one entry for the port #. Is it possible to set uf port ranges in 877 router?

View 2 Replies View Related

Cisco VPN :: ASA5540 - Windows Client Cannot Add ARP Entry

Sep 13, 2011

In my environment, VPN users are connecting to corparate network via ASA 5540 and using  3.5.1, 4.8, 5.0 (32 bit) and 5.0(64 bit) VPN clients.After they have built VPN connection, they use program that generates traffic to a bradcast address (x.x.x.255) inside corparate network.

There is no problem with users who are using 3.5.1 and 5.0(64 bit), but 4.8 and 5.0 (32 bit) vpn clients can not add ARP entry to Windows machines ARP table. If i add ARP entry for x.x.x.255 on VPN interface, they can work.

View 1 Replies View Related

Cisco LAN :: 2651XM - Clear Entry From Configuration

Oct 2, 2012

cisco 2651XM router
IOS:  c2600-adventerprisek9-mz.124-15.T8.bin
 
if I do #sh arp in the terminal with this router I see a rogue entry thus:
Internet  192.168.0.4             0   Incomplete      ARPA

My whole LAN operates on 172.16.x.x/16, there are no 192.168.x.x devices connected. In the past I've had 192.x.x.x devices running but for a long time and the router has been restarted since then. I've tried several clear commands in the terminal but this entry is stuck there and I've also seen it in a wireshark scroll on a pc when monitoring the routers' adsl traffic - it shows up an an SNMP entry and I do use SNMP on my router, but that data goes to a 172.16.x.x. machine. How can I clean this entry out?

View 8 Replies View Related

Cisco Firewall :: Duplicate ARP Entry With ASA 5510

Jul 17, 2012

I am having peculiar issue in my setup. I recently replaced my ASA 5505 (8.2.1) with ASA 5510 (8.4.3). Everything works fine for a while suddenly I see some of the servers will not be reachable from the LAN all the servers gateway is my switch. If I check on my Dell switch the particular server's arp entry on the connected port  is same as ASA physicall MAC. If im reverting to 5505 ASA everything goes smooth without any issue.

View 6 Replies View Related

Static IP Address Entry Will Not Save?

Feb 24, 2011

Everytime I start one of my two Windows machines, I need to go to the control panel network adapter and enter the static IP address in the IPV4 properties. It is always blank after a shutdown.I have two machines that are networked for flight simming.One of the machines must have a static IP so I configured both static. Not sure if this has anything to do with my problem.

View 5 Replies View Related

Cisco :: ARP Database Timeout?

Aug 16, 2012

How do I, if I even can, adjust the MAC table timeout from 5 minutes to whatever is bigger and allowable?

I would like to also like to change the ARP table timeout as well.

View 4 Replies View Related

Cisco :: LMS 4.1 / Building DSN For UPM Database?

Jan 26, 2012

I need to generate an ODBC connection to the upm Datasource on LMS 4.1 running on Win2K8.  I have successfully built connections to cmf, ipm and rmeng, however UPM keeps failing saying that the Database is not found.
 
Here are my settings.
 
Driver = CiscoWorks Embedded Database
ODBC Tab - Data source name = upm
ODBC Tab - Description = Device Performance
Login Tab - Supply user ID and Password is selcted
Login Tab - User ID = lmsdatafeed  (i have tried DBA as well)
Login Tab - Password = set using the password I estabplished with the dbaccess.pl and dbpasswd.pl scripts
Database.Server name = upmEng
Network.TCP/IP = HOST=<lms server ip>;DOBROADCAST=NO;ServerPort= 43800
 
I validated the server port using netstat -a -b -o and matching up the PID with the UPMDBEngine process shown in the LMS Manage Processes window.Windows firewalls on the remote machine and the LMS server are off.

View 3 Replies View Related

Cisco :: LMS 3.2 - How To Access Database

Sep 22, 2011

what is the database to use cisco LMS3.2 and how to access the database?

View 3 Replies View Related

Cisco :: LMS 3.2 Need To Restore Cmf Database

Aug 29, 2011

If i reinialize(restore) the cmf database.do i need to reinialize all the databases.???
 
or if i reinialize the cmf database and do bulk import the devices is enough?

View 3 Replies View Related

Cisco :: ASA 5510 - AnyConnect Invalid Host Entry

May 3, 2012

I have a 5510 using AnyConnect VPN clients. I have a DNS name for my router to accept connections ie cisco.mydomain.com..I can ping the address by hostname from the clients machine ok but when the AnyConnect client opens it has my hostname ie (cisco.mydomain.com) but says "invalid host entry" I have to type in my IP address for it to connect.I have the hostname in my AnyConnectProfiles.xml.

View 1 Replies View Related

Cisco Firewall :: ASA 5510 Ignoring Configured Acl Entry?

Dec 16, 2011

I'm configuring up aa ASA-5510, and I have several interfaces, some of which include:
 
interface Ethernet0/0.200
vlan 200
nameif SITECORP
security-level 90
ip address 10.1.4.1 255.255.254.0
!

[code]....
 
This definitely confuses me, because SITECORP has an inbound access-list of permit ip any any.

View 5 Replies View Related

Cisco Switches :: Manual Multicast ARP Entry For SG300

Jan 22, 2012

We're replacing our older catalyst switches with new SG300 family switches and have a Microsoft NLB cluster for some services that run in multicast balancer mode.
 
We currently do L3 routing to the network with the cluster and have the following IOS configuration line in the specific switch to let users on other subnets to access the services.
 
arp 10.20.1.226 03bf.0a14.01e2 ARPA
 
How do we replicate this using the SG300 series in L3 mode? Whenever I try to add a manual ARP entry I get an error message that says that the MAC address is not a valid unicast address?

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved