I am on the Verizon wireless router connected to my laptop and the xbox wired to laptop. I have another wireless router that i want to connect because the main router is in the basement I am on the second floor. How do I connect the xbox to the 2nd router wired?
View 1 Replies
my goal is to share my cable modem signal over my two story house using two wireless routers. The delima is that the routers don't support wireless bridging and if they did, the signal is too weak to make it worth while.
The remedy I came up with... buy a pair of powerline network adapters and connect one router to the other so I could have a good signal upstairs and then a good signal downstairs.
Downstairs, I have the cable modem connected to the Linksys WRT54G router, which has a line out to my blu ray player, wirelessly feeds a PC downstairs and then has a cable run to the powerline adapter.
Upstairs, I have a cat5 connecting the powerline adapter (which was tested and works with laptop) to the data input port on my second wireless router, the netgear wndr3400.
I can't get the netgear upstairs to pull an IP address from the linksys router downstairs over the powerline network.
i have issue for Remote App to connect to the Apple TV using the Wireless network setup in my 180W.My wired Mac is able to connect to wireless connected Apple TV but my i phone (4, 4S and i Pad) are not able to connect to apple TV.
Do I have to enable some setting for this to work. It used to work in my very old Buffalo router with tomato firmware.
If I connect the Apple TV to wired network it works fine. Instantly it shows up in i Phone Remote app, but not if its on wireless network.
Is there any way to disable router devices from connecting to your network? For example I want people to connect ethernet cables to their laptops, ps3s, pcs, etc but not to routers. How would one go about doing that?
View 1 Replies View RelatedI have a desktop connected to our work network. It's running XP Pro. I also have a laptop running vista home. Is there a way to hardwire that laptop to the desktop, so i can share files between those two computers, while ALSO keeping my desktop connected to my office network?Since it's vista home, I can't connect the laptop to our network, since it can only connect in workgroups, not networks. But if I'm just able to just use the laptop, create files, and then either save them to a shared folder with my desktop or just save them to the desktop with a switch or something, it wouldn't be a problem that my laptop can't connect to the network.
View 3 Replies View RelatedI put just got a wrvs 4400N and when I replaced my old linksys router I can't access my network computers anymore. I'm I missing something or do I need to do some kind of setup?
View 3 Replies View RelatedI have HP laserjet 4000 tn. Had an old router and upgraded to a new wireless router, when connecting it to the new router, the port I connect to has the amber light come on. I have reset to factory setting thinking it would reset and capture a new ip address. still giving me problems. try connecting it to my macbook pro and cannot get a "fix" on the printer either. I know it has to do with the configuration of the printer.
View 3 Replies View Relatedtrunk port connecting but not allowing access to tree; i connected 4506 port to 3550 port; and i set both to switchport mode dynamic desirable; the 4506 port was set with switchport mode access and switchport mode access vlan ?; i used the command default switchport access vlan to remove the vlan; the ports are up but as I stated I cannot connect ot our workgroup tree
View 4 Replies View RelatedI have a belkin surf n300 usb wireless N micro adapter. No problems installing this adapter on a HP Desktop running windows 7. I have tried to install on a gateway laptop also running windows y 64 bit. In device manager it show that the product is working. It will not connect to any network. The adapter is an F7D2102 az ver. 2011az
View 2 Replies View RelatedI have a Kguard H264 CCTV system installed that is connected to my BTHome HUb 2 via ethernet cable.The CCTV system is registered on the home hub and has a direct ip address of 192.168.1.100 and is configured to forward port 80 which is correct.Problem is how do i now connect to the CCTV system outside of my home network i.e. using my work computer?
View 4 Replies View RelatedConnecting two wrg614 routers together. Have cable one as my provider. Both are wireless routers, however I want the second router to have only 3 pc hardwired in, no wireless.
View 1 Replies View RelatedI have two wireless modem/routers - a Ugo Mach5 CN458 and a Swift 4G - in two branches of my company that are distance apart and i want to connect them together so that they can be on the same network and workers in both branches can communicate and share files.
View 2 Replies View Relatedi have two linksys wireless router on different networks that i want to connect. how do i go about it?
View 1 Replies View RelatedWe have a Linksys WRTU54G-TM that serves both as a hotspot and phone line (T-Mobile). But since it's a G, the radius doesn't cover the whole house. So instead of buying an antenna, we bought another router (Cisco Factory Refurbished Linksys E1200 Advanced Wireless-N).
So the question is: How do we connect both routers to one modem properly, the N-Wireless to be used when necessary?
Basically my sister, who lives in a flat attached to the side of my parents' house, wanted me to find a solution for her to get internet, as there is no signal from my parents' wireless down in the flat.Originally I tried an old belkin wireless range extender I had lying around but even then the signal was extremely weak and the connection was too slow.So, I decided I would get some powerline adapters. But, of course, my sister needs wireless, so I figured I would use the powerlines to connect a second wireless router to the existing one.And so begin my real problems. The thing is, it actually worked fine at first. I set up a new wireless network, and had the ethernet from the powerline running in to the WAN port of the second router. But, every few minutes or so the connection would just die suddenly and take a while to come back (the connection was still there, but the browser just gave DNS errors etc).So I did some googling and fount a lot of people saying that I had to A) plug it into one of the LAN ports, not WAN, and B) disable DHCP on the second router.However when I do this I simply cant load anything at all. I'm thinking maybe there's some additional setup regarding static IPs or something that I need to do when I disable DHCP?
View 5 Replies View RelatedI'm using my AE1000 to connect my computer in my home office to the router downstairs. The problem I'm having is my neighbor's routers show up on my network connections and it ends up slowing down my internet. Is there any way I can keep my adapter from trying to connect to my neighbors?
View 2 Replies View Relatedin our small office, we are using Cisco SRP527W (Router/ADSL Modem all in one ) and D-Link DGS-1210-16 (ports) as our main network devices, our 3 desktops (Windows XP), Avaya phone system and one Brother MFC 6490CW are wired connected to our D-Link switch, port1 of the switch is connected to lan port 1 of our Cisco router, we also have 3 wireless devices connected to the cisco router throught wireless signal (one Broher MFC J6910DW printer, one laptop with Win7, one all-in-one desktop with Win8), as we know, both Switch and Router support Vlan feature, but at the present, I just use default Vlan (Vlan 1) for all our data traffic, I created a DHCP Pool in Cisco router to provide IP address to all our devices (DHCP Pool: 192.168.30.101 - 192.168.30.250, Default gateway is 192.168.30.254), All wired or wireless devices can get right IP address,and all of them are able to get on to the internet, the problem is wireless and wired devices can not talk to each other, for example, my laptop is using wireless connection, when I try to ping a desktop which is wired connected to switch, there is no response, however, if I cable connect my laptop to switch, I am able to talk to the desktop and use its shared resource.
View 2 Replies View RelatedI am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
View 3 Replies View RelatedI have two BELKIN f5d7230-4 wireless router my goal is to connect the two wirelessly and share the internet connection.
View 2 Replies View RelatedI have linksys router connected to my cable modem. I want to change it Belkin AC900. How can I keep the linksys connected until I have tested set up for Belkin AC900 router.
View 2 Replies View RelatedI have what should be simple. Home network on cable. WRT320N is main router cabled to desktop with GB card. It is hard-wired to a Netgear WNR3500L (also gigabit). That router is hard-wired to a desktop with GB card. For testing I connected a second machine hard-wired to the WRT320N with a 10/100 card. All machines recognized cards properly at correct speed. I ran LAN Speed Test between machines. Speeds were comparable between machines regardless of cards. GB -> GB was mid-30's write, mid-80's read with GB -> 10/100 a couple of ticks slower but not significantly. The LED's on both routers will show different color if GB connection and both showed GB for the desktop connection but not the interconnect between the routers. The routers are connected at about 100' with CAT5E and straight-through.
View 5 Replies View RelatedI can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 1 Replies View RelatedIs it possible to integrate a wireless voip cisco 7921g (sccp protocol) with an small business modem router Srp527w (sip protocol), even if if is by connecting another device (like an access point) between both? I know skiny is cisco property and sip is an open source protocol, so I do not understand why cisco does not implement the skinny protocol in his Srp527w.
View 5 Replies View RelatedI tried to bridge two wireless routers wirelessly, but after extensive research I came to the conclusion that this wasn't possible.
Now I am trying to connect these two routers through a cat5 cross-over cable and I wanted to know whether can I disable DHCP on the router which has internet, and enable the DHCP of the router which is connected to the printers, because I have a few systems that shouldn't be connected to the internet.
What I had in mind is if I switch the DHCP OFF on the internet router and turn it ON on the Huawei B683 router, I could add those devices' MAC addresses to the internet gateway router to deny them access to the internet..?
I have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
View 1 Replies View RelatedI have two AC1200 routers? how do i connect one ac1200 to another ac1200. Only one should act as a DHCP server and broadcast wireless; the other should be simply just a hub (vs. me having to buy a separate hub). What are the correct settings and connections?
View 1 Replies View RelatedI am trying to connect a Seagate Backup Plus 4TB USB HDD to the USB port on my Belkin ShareMax N300 wireless router. The router does not recognize this HDD. I know that the HDD is functioning because it works when I connect it directly to my laptop USB. I also know the Belkin USB port is working because it recognizes a 4GB USB memory stick and a 320GB Toshiba USB HDD. Is there a fundamental compatability problem, or is there some configuration that must be performed (e.g., reformat from NTFS to FAT32, etc.)? I saw some message traffic on the Belkin support site that indicated some issues with earlier versions of Belkin routers using larger HDDs (e.g., 4 TB). My router has a serial number 121026G3101468, model number F7D7301 v1.
View 3 Replies View RelatedI am having trouble connecting the Amped Wireless AP600EX access point to my WRSV4400n. As soon as I plug the range extender into the router, instead of it receiving an IP address, it crashes the router. I have updated the router firmware to 2.021. I have checked the box in the WDS menu to "allow wireles signal to be repeated". I will check with Amped, but are there any known issues between this router and the Amped Wireless family of range extenders?
View 1 Replies View RelatedSo I just got a wireless presentation gateway wpg 120 to connect to projector wirelessly. For me to connect to the projector i need to set wireless network to its wireless connection. But if I connect to wpg 120's connection, there is no internet access.Is there any way I can connect to two wireless network or use wpg 120 to connect to internet using it's connection.
View 3 Replies View RelatedI have a medical office and am trying to connect my netbook to the office networkThe netbook can connect to the internet via wireless. I want the netbook to connect to the network drive that has my office data and program. How can I get the netbook to see the network drive on the server
View 2 Replies View RelatedI have a PC network in house using a netgear router. One of the PC is cable-connected to the router and the other using wireless network adapter. Now I have a Sony Blueray player which support network connection. How do I connect it to the network?
View 1 Replies View RelatedMy problem is my laptop is not connecting to the only network in my home and I can connect to all other wireless networks around.Also there is no problem with the router/modem coz all my room mates can connect and access internet wireless and also through Ethernet.Even I'm able to connect to the home network using Ethernet but not wireless. Strange but true!
[code]...
connect my partner's laptop to my wireless network?
The router is a Sagem provided by my ISP (Sky). The wireless connection works fine on my MacBook, and various other devices connect no problem with the security key.
However, his laptop (Windows Vista) will not connect wirelessly. After entering the password, it says it can't connect because it 'times out' (we are obviously entering the password immediately with no delay). It connects fine with an ethernet cable. It will also connect to an unsecured wireless network we can pick up.
The security setup is WPA-PSK with TKIP encryption, and we've made sure he is using these settings.
If it might be important, he has just moved here, and previously his laptop was connected to another Sky router with no problems.
