Could Windows 2008 Work As A NAS

Jan 13, 2012

My computer has today 3x2 TB WD Green disks and thay are really slowing my system down so now I need to move them to somekind of NAS.I was first lookin at the "Synology Disk Station DS411j" but then I found that I got some old hardware laying around (AMD 3200+ CPU, 1 GB ram,XFX GeForce 7600GT, Seasonic SS-300FT in a Thermaltake Xaser II chassi). So now I got some questions :

1. I was looking into running FreeNas on my NAS but if the NAS is crashing then it will be alot of work to get the data back? Is it right that its not possible to just mount a drive from the FreeNas in to my Windows7 computer and read the data?

2. If I install Windows 2008(not r2 that demands 64bits CPU) and then uses dynamic volums to get one big volume, what will happen if this Windows2008 craches? will it be able to place one of the disks in my windows7 computer and reda the data?

3. What happens if one disk i a dynamicvolume craches? will all data be lost?

4. Is there any sleepmode in Windows2008? If would be nice if the computer shutsdown at night and startsup when it is about to be used.

5. Will a finished product like the "Synology Disk Station DS411j" demand less power? Will I earn anything to buy the DS411j instead of my old hardware if we look on the economics?

View 2 Replies


ADVERTISEMENT

Dell :: Precision M4500 - 1397 WLAN Mini Card To Work With Windows 2008 X64 R2

Oct 25, 2011

How to successfully get a Dell Wireless 1397 to work with Windows 2008 x64?  I have a Precision M4500 that I managed to install Windows 2008 x64 R2 on.  I installed the Windows 7 drivers for the card and the Device Manager says the device is working properly.  But when I go to enable the device, it acts like it is enabling it, but the properties always say "disabled".

View 1 Replies View Related

Cisco Firewall :: ASA 5520 CIFS Doesn't Work For Share Folder On Windows Server 2008 R2

Jun 26, 2010

I am using ASA5520 with webvpn for file sharing. But recently we just upgraded the OS that accommodate file shared folder from win2003 R2 32bit to windows server 2008 R2 64bit. Now I have a problem with accessing file share by ASA webvpn, it appears error contacting host, we have tested the file shared of webvpn on the other OS windows 2003 and windows 2008, they are working on these OS except win2008 R2. Current the ASA OS version is 8.0(2). And the windows firewall has been disabed.

View 3 Replies View Related

Cisco :: Is LMS 4.0.1 Supported On Windows 2008 R2 64 Bits With 2008 R2

Oct 24, 2011

I planned to install a LMS 4.0.1 on a VMWare server with Windows 2008 R2 64bits.
 
Is it supported with the "Windows 2008 R2" patch or do I need to order LMS 4.1 version ?

View 5 Replies View Related

Cisco VPN :: ASA5520 - Getting AnyConnect To Work With New 2008 Radius Server

Sep 14, 2011

We are in the process of upgrading our win2003 radius server with a new win2008 radius server.  We have an ASA5520 and FWSM  in 6509, using anyconnect client.  This has worked fine until we introduced the win2008 radius server.  When in the asdm on the asa, you can click on the new server and click test and authenticate ok with your AD credentials.  But when try to use anyconnect on your laptop, it takes the credentials password and the accept certificate, but then fails with "anyconnect was not able to connect to specified gateway.." message, then "the secure gateway has rejected the connection attempt due to network connectivity issue...host or network is 0" message. We thought we setup the new radius the same way, obviously not.  is therw an easy way to use debug on the firewalls to see what is wrong?  looked in event logs on radius server, have not found anything.

View 2 Replies View Related

Windows Server 2008 With Reg Key?

Mar 7, 2013

I am running a small network of 30 pc. I have installed windows server 2003. Now i want to upgrade it to server 2008 but before that i want to test windows server 2008. That is why i,m looking online for a copy of windows server 2008 with reg key. Is there any good and trusted place to get windows server 2008.

View 1 Replies View Related

Windows Server 2008 R2 VPN

Aug 13, 2012

I have a dedicated windows server 2008 r2 enterprise.I am running an SSTP VPN but only have 2 IP address to connect to the internet on.My issue is that one of the IPs is for the IIS7 etc and the other is for VPN use.How can I apply the same IP to more than one user allowing them to connect all at one.There are in total about 5 users who want to use the VPN service and I dont really want to pay.How do I apply the same IP to all accounts and allow them to connect and all use the same IP at once.

View 5 Replies View Related

How To Build NAS With Windows 2008

Apr 13, 2012

I'm wanting to make use of an old PC here that has Windows Server 2008 on it. i basically just want to use it as a backup machine. i have 1 PC, 1 Mac and an iPod Touch that'll be accessing it. what do i need to do to set it up? is there a guide anywhere? how is it different to setting up a NAS using FreeNAS?

View 3 Replies View Related

Servers :: Os2 Networking To Windows 2008

Nov 2, 2011

I need to connect a OS2 pc with Windows Server 2008. However, I have tried the Netbeau (which can work in connect with Windows Server 2000), I cannot install the Netbeau to Windows Server 2008.

View 2 Replies View Related

How To Use Windows Server 2008 As Router

Sep 4, 2012

I am involved in a huge project that requires Servers PCs to function as Routers in schools to prevent broadcast traffic issues (Thread here: Need Professional Advice on 3 MANs implementations - Long story short: Can't buy regular routers because of budget and neet to use current equipment to make the network work, that is, Windows Servers 2008 with 2 NICs.

Now to the point. We are making tests but can't make Static routes to work properly. Design is as follows:

Now we have seen that we need to use this command (in cmd) to add a static route in W2008:

route add [NETWORK DESTINATION] mask [SUBNETMASK] [GATEWAY] if [NIC]

Q1: What exact command(s) do we have to use to make the Laptop in 10.10.10.0 to access Internet? How would you fill those fields based on the diagram?
Q2: How many Static routes do we need to declare? I am guessing we just need one, but I have been told that I need to activate two (one for packets sent by the laptop to the router, and one for the packets sent by the router to the laptop?)

We have tried several combinations and can't make laptop to access Internet, not even to ping 192.168.1.5. We have just accomplished pinging to 192.168.1.181 from the Laptop, and to ping 10.10.10.2 from the Server but that's as far as we went.

View 4 Replies View Related

Can't Join A Windows 2008 Server

Jul 17, 2011

I can't join a Windows 2008 Server from client computer running Windows Vista Business Edition. I get the message "Network path not Found" yet I can ping the server and the server can ping my computer.

View 2 Replies View Related

Installing Windows 7 On Server 2008 LAN

Mar 24, 2012

Any methods to install windows 7 OS on 3 laptops at a time by using windows group policy management in Server 2008 LAN.

View 1 Replies View Related

Windows Server 2008 R2 With Dynamic IP?

Jan 9, 2013

I have a home server that I'm using to host a site with a domain purchased from Go Daddy. I understand how to set up a static IP address on Win Server 2008, but my provider will not allow for me to purchase a static IP because I'm a home customer, not a business.My question is this: should I just ipconfig my ip address every seven days and then change my server's address? Is there a software alternative? Is it necessary for me to change it at all?

View 1 Replies View Related

How To Setup NAT In Windows Server 2008

Nov 5, 2011

i m having one static ipwant to create the network in computer labhow i do thisi have one cisco router assigned with one ip address

View 1 Replies View Related

Static IP For Windows 2008 Server R2

Jun 17, 2012

I want to run my own web server. i have Windows 2008 Server R2. we hv one router for internet and it is linked with switch. 30 computer are running on local LAN and getting Internet. now my ISP give me a block of IP. i want to give it to web server. what is the simplest way to use that IP and my web server is Online and also all user have to access to Internet.

View 4 Replies View Related

Using Windows Server 2008 R2 As Webhost?

Nov 8, 2011

Is it possible to use windows server 2008 as a webhost for a website i'm building?

View 6 Replies View Related

Cisco :: Does WCS 5.0 Run On Windows 2008 Server

Feb 8, 2009

Does WCS 5.0 run on Windows 2008 Server. Does it run on a 32 or 64-bit OS? The WCS datasheet does specify that it can be easily installed on VMware Systems. Does it mean it can be virtualized. 

View 6 Replies View Related

Cisco AAA/Identity/Nac :: ACS 4.2 And Windows 2008 R2 CA?

Apr 30, 2012

getting a cert off of a 2008 R2 CA and imported correct in to ACS 4.2?  I've had and have seen other have the problem with creating a web server certificate from R2 (1024 bit) and putting it in ACS 4.2 only to have HTTPS/SSL no longer work correctly.  I haven't even tested the intended purpose of the cert (EAP-TLS) yet, so who knows if that works.  I've also seen through searching where some one was able to take a 2003 CA web server template and put it into R2 and it work, but I know longer have 2003 available?

View 1 Replies View Related

Cisco :: Configure WAP 321 To NPS On Windows 2008?

Feb 3, 2013

We want to configure a Cisco WAP 321 to NPS on windows 2008.

On NPS system event viewer :
 
An Access-Request message was recived from RADIUS client XXXXXX with a Message-Authenticatior attribute that is not valid.
 
We have installed other RADIUS client on Windows 2003 Server and we have the same error.
 
On the Web interface of Cisco WAP only can configure the IP and password of the Radius server.

View 1 Replies View Related

Cisco :: Change LMS 4.0.1 From Server Under Windows 2003 To New Server Under Windows 2008 R2

Jul 5, 2012

I planned for my customer to replace his old LMS 4.0.1 server under Windows 2003 by a new server under Windows 2008 R2.Customer wants also to set a new LMS name and IP address for the new server under Windows 2008 R2 and keep both servers on the network.I'm wondering what could be the best procedure to do that migration.Can I used backup / restore procedure in that case ?If yes, what file must I modify to adapt the new LMS configuration to new hostname and IP Address ?

View 2 Replies View Related

Windows Server 2008 Core Installation

Jul 27, 2011

Any here ever used a Windows Server 2008 Core installation? Got one running on a VM right now, thought I'd try it. After installing VMWare Tools things really speeded up. Now gave it a static IP, installed Active Directory services (DNS along with it) and everything seems to work. The RAM usage is about the same, but so far it's been much more responsive, and it takes a lot less disk space, it needs just under 3GB for the moment. Any else here have one running, or seen one in a production environment? I don't think they're very common yet.

View 3 Replies View Related

Desktop Redirection In Windows 7 On Server 2008 Dc?

Jul 26, 2011

im having problems getting desktop folder redirection to work on windows 7 machinesI have users set up just with local profiles but want to redirect "my documents" and "desktop" directories to the server. I have set up the gpo's on the server and it all works fine propergating to the xp machines but the windows 7 machines just wont take the desktop redirection. However "eventually" it did take the "my documents" redirection policy

View 7 Replies View Related

Vpn And Mapped Drives Server 2008 Windows 7?

Jan 30, 2013

I have a windows 2008 foundation server at a clients property and they wish to have users access shares on a data drive that is seperate on the server.I have the server setup with active Directory Users and logon scripts to their local shares on the data drive but need to setup VPN so they can use their mapped drives at home.

View 1 Replies View Related

Windows 7 Ultimate Cannot Join SBS 2008 Domain

Jan 18, 2013

I have set up a Small business server environment for a client. One server in the network, it provides both DHCP, and DNS. Joined all of the XP machine to domain no worries. Tried to join the 7 machine and I get a "DNS couldn't be resolved" error. I know DNS is functioning properly on my server.

View 1 Replies View Related

Installing Windows 7 Using GPOs On Server 2008

May 27, 2011

What are step by step methods to install windows 7 OS on 3 laptops at a time by using windows group policy management in Server 2008 LAN.

View 1 Replies View Related

Setting Up A Network To Run Windows Server 2008?

Nov 29, 2012

i am setting up a network with a server able to run windows server 2008 and using duo core computers as work stations. Will it work with using windows 7 as the operating system for the work stations?

View 5 Replies View Related

Windows Server 2008 / RDP Through Router - No Control

May 1, 2012

I have an office with a network that I have no control of. I can't access the router to make changes at all. The router does have a real IP address.There is a server on this network that I need to access through remote desktop. (Terminal services on Windows Server 2008)Normally I would just pass 1723 through the router and set up VPN. Without control of the router I am lost. I really don't want to use services like Logmein or Gotomypc, because these control the console.

View 1 Replies View Related

Windows 2008 R2 Server - Error 105 For Gmail Only?

Mar 8, 2013

I run a tiny home domain with 1 Windows 2008 R2 server and 2 clients (one for me and one for the hubby). Our server is DC, DNS, and DHCP server (and some other roles). Our clients are both Windows 8 but we use the standalone Chrome installation, version 25.0.1364.152 m.The problem is that on my Windows 8 client, every once in a while (not the same time period each time, but roughly every 6-15 days) I get the error in the title on one site when using Chrome only, which is Gmail. I can access and resolve Google and every other site, and my DNS server itself can resolve Gmail, but not until I flush the DNS of my local client will Gmail work again. Also strangely, I have left it on the morning when it happened before, and when I came home from work it had sorted itself out. The other client, hubby's Win 8 PC, also sometimes gets this issue, but not nearly as often as I do. Flushing the local DNS cache resolves it for him as well.

I used my ISP's DNS servers for forwarding initially, but changed to Google's 8.8.8.8 and 8.8.4.4 when this kept happening, and it didn't seem to make a difference. I've enabled scavenging and aging and all sorts and those are faithfully renewing themselves as expected, but as the problem only lies on the clients and never the server, I'm quite lost as to what to try next.I've had a look on the Chrome forums (gulp) and nothing seems to be as specific as this fault

View 1 Replies View Related

Servers :: SBS 2008 - Add Windows 7 Computer To Network?

Jul 7, 2011

One of the computers at my office died and needs to be replaced. I need to get the new computer set up with an existing user account so that the user can access email and public drives. The new computer is running windows 7 professional.Our server is running SBS 2008.

View 5 Replies View Related

Windows 2008 Server / VPN Not Working Externally?

Apr 29, 2011

I just finished setting up VPN server on my Windows 2008 server. I defined the users that should be able to access the server and applied permissions. When I test the VPN connection on the LAN (loacally) I have no trouble connecting and establishing VPN connection.However when I tried externally it's a different story. I am not able to connect and always get the same not so clear 800 error ...The remote connection was not made because attempted VPN tunnel failed. I have Zyxel router for my internet connection and I have forwarded all relevant ports I think for the protocols I am using. Port such as 1723,1701,1702,47,50,51,500,1293,443,4500 are forwarded to the server.I am able to telnet to the server on port such as 1723.

View 1 Replies View Related

2 Servers 2008 / 20 Windows 7 Computers - 10 And 100 MB Speed?

Oct 1, 2011

I have 2 servers 2008 & 20 computers win 7 i need to give for 10 MB Speed for some computers and the others computers 100 MB Speed How?

View 1 Replies View Related

Cisco :: Error During LMS 4.2 Installation On Windows 2008 R2

Jan 28, 2013

I am installing LMS 4.2 on Windows 2008 R2 standard edition 64 bit. During installation its showing the following error.And I am not able to proceed the installation.

View 1 Replies View Related

Cisco Security :: ACS Se 4.2.1.15 Patch 4 And Windows 2008 R2

Feb 27, 2011

Whether ACS Se and Remote Agent 4.2.1.15.4 supports Windows 2008 R2.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved