I have a DCS-930L wireless webcam. I can view the images on mydlink. Is it possible that mydlink take pictures with my webcam and then every 10 minutes sent to my domain[url].....? Who has experience with this link between mydlink and Internet?
View 11 RepliesI urgently need to create a DCS-930L java script for a my website so that the streaming images (different from the visible images on the "my dlink service") can be viewed by visitors even if my PC is off and only router work.In the Modem/router Linksys WAG 320N I opened port 80 (port forwarding) but I can not see them on the web.
View 1 Replies View RelatedNewly purchased DSC-930L connected to DIR-625. Firmware is 1.0 for DCS-930L and A1-1.09 for DIR-625.Camera works fine when connected with cable. Wireless enabled, fixed IP address.Unplug cable and camera still works fine for a while: can access the view page and view picture that does change. F5 refreshes page no problems. After a while (about 5 minutes) web page no longer reachable by browser. Reconnect cable and works fine, unplug and repeat the cycle same thing happens.Also tried: unplug ethernet cable, unplug power cable, wait 10 seconds, connect power cable, try to browse to camera - cannot reach camera.
View 13 Replies View RelatedI'm using a Verizon DSL router, Mac D-Link Camera Setup Utility (BETA), and Mac OS X 10.6.7. Configuration of camera is as recommended in manual with CAT-5 cable. Green light blinks irregularly in a communicating-with-router manner. The setup utility won't recognize the camera
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 110620
ISP : BE Broadband
I have an issue sending pictures via iMessage on iOS.
I have a H.264 web cam with a built in server attached to a 1 watt Powerlink(N) router(bridge) connecting wirelessly outside (100 feet)to my Dlink 655. My computer connects wirelessly(60 feet) through the house via a 1 watt Powerlink USB adapter to the 655 also. It was the Network from hell to get up and going, but it is functional? now.I have the Dlink with a web server port open outputting the video. I can access internal and externally via IE with a Dyndns domain so its all working.Dlink says I'm getting 80-160mbps from the web cam and 25-55mbps from my computer.The Problem: Camera server comes up fine and starts to stream great video for 2-5 seconds then its like the bandwidth gets used up and it gets choppy, stalls for long periods ETC ETC. I have Nat TCP and UDP set to End point independent if that makes a difference.
View 10 Replies View RelatedHow can I configure DCS 910 webcam if I don't have the software CD?
View 4 Replies View RelatedI would like to share my live video from my dcs-930L camera but don't want to give out my password that would allow people to change settings..
View 3 Replies View Relatedi was playing back the recording,when i skipped ahead, the sound disappeared. I am recording 10 hours worth everyday, most of the time i just need to skip to a certain time to see and hear what was going on,
View 2 Replies View RelatedHow to add an external antenna? I'd like to mount a DCS-930L in a location (inside a metal housing) that would need the antenna to be a few inches away. Any internal layout information?
View 3 Replies View RelatedI just brought this D-Link DCS-930L. I insert the disc and follow the instruction and select the option of without WPS and follow the step of connecting the lan cable and power point but at Step 2, after the green light, it keep prompting me that it can't find the camera. it connected to the router where there is a lan cable connected to my pc.
View 1 Replies View RelatedI had to get a new router from verizon cause the old one died. so i reset the camera and wipe all the dlink software and settings. I then start fresh. i get all the way to choosing wireless and input the password. It states that there is a problem saving your settings. I tells me nothing more. I spent 4 hours on the phone with tech support and i can get it working through wired but I can't put it in my childs room wired. it worked perfectly before the router switch. funny thing is that its the same brand and model router.
View 4 Replies View RelatedI downloaded the MAC setup Utility(BETA) and it can't find the camera.The camera is connected via Ethernet-Light on the front under the lens is green (blinks sometimes)First thing I noticed wrong was the setup utility asks if the light on the side of the camera is lit green-there's no light on the side of the camera as far as I can tell. I tried unplugging the camera and hitting the reset button on the back-nothing works.
PC: MAC OSX 10.6.7 (2.2GHz Intel Core 2 Duo/4GB RAM)
Router: Linksys WRT54G Wireless-G Broadband 2.4GHz
Browser: FireFox 4.0.1
i installed cameras but want to set up for motion. I have 2 dcs 930l cameras and I can see them live i have only 2 settings live video and camera info i also downloaded the link from support.dlink.com i have a new windows 7 laptop and it keeps tryng to download java app problem is now computer keeps asking for a username and password and I have no idea what username and pw it wants as it says in the box it is unsecure
View 1 Replies View RelatedI just recently purchased the DCS-930L wireless camera, and I am trying to connect it to my Netgear router but it states that there's an error and can't connect. My itouch and laptop connects fine with the router.
View 6 Replies View RelatedIs it possible to install the D Viewcam software on a PC that is offsite (different network) as the camera and record from there? Basically the camera is home and you record from work.Can I record directly to any NAS (same network as camera) without having a PC in the middle? Or do I need a specific NAS?What about one of those external hard drives that hook up directly to a router?
View 1 Replies View RelatedI have the DCS-930L set up at home with motion detection emails. I only want it to be sending emails when I am not home, of course, but there's no way to turn off the camera through my dlink.com as far as I can tell (only an option to remove the camera, which I assume is something more drastic). Is my only choice to unplug the camera when I don't want it emailing?
View 6 Replies View RelatedI am able to access 930L (2 cams) from wifi be it laptop,iphone or ipad but I am not able to see it through 3g.I have Huawei fibre optics broadband reuter from Starhub.Starhub is running away if ask them to fix it. Huawei never takes the call.I tried atleast 3 times 10 minutes each at 8006011450.It goes to disconnect. The lot talked about UPNP is enable in reuter but it does not work.
Now i talked to Dlink support with ticket DCX36811.They advised to load the firmware.I did it still the connection timeout is there. we have baby to monitor through iphone/android 3g.
I bought and hooked up my DCS-930L camera last week. Have since traveled overseas and go to Mydlink website, log-in and then it tries to install a java applet that never does install. It shows the security box where it asks me to run and then it shows another security box with a message: java.io.FileNotFoundException:C:usersmynameAppDataLocalLowSunJavaDeploymentsecurity rusted.certs(Access is denied)
I click ok and the java applet never loads. It just keeps saying Installing Java Applet.
I have a DCS-930 running successfully on my home network. Now I want to set up a DCS-932 on a different network at my mother's house in another city, so I can monitor her house from a distance. Questions:
1. After installing, will I be able to see both cameras at mydlink.com if they are on different networks?
2. Is installation any different because there are 2 networks?
3. Can I use the existing install wizard on the laptop that I used with the 1st installation or should I use my mother's PC?
4. How do I get started since the first instruction is to insert and use the CD that came with the new camera?
Basically I want to know what the install procedure is if I am using a different network but the same laptop I used with the 1st one. The laptop has a wireless connection to both networks.
I think I did everything per the manual, but I cannot access my camera over the internet thru [URL] website. It says that I have to check if I have enough bandwidth, or checked if my camera is not blocked by my router But I have a Dlink DIR 655 router where I have configured the Virtual server (port 80) as it is explain in the manual I also have a DHCP reservation that works fine (I can access the camera within my network) What should I do more now to finally access my camera from internet (this is for me the interest of havinf a network camera!)
View 14 Replies View RelatedIs there any way to turn off the front green LED on the DCS-930L or do I just cover it with a piece of opaque tape?
View 2 Replies View RelatedI am using a Mac and would like to view the live feed full screen. Is this possible?
View 3 Replies View RelatedMy DSC-930L's web interface becomes unresponsive about an hour or two after power cycling my camera. It still responds to pings, and it still sends images to FTP when it detects motion, but I can't log into it via web interface, mydlink, or the iphone app. Power cycling the camera fixes the problem for an hour or so but then its right back to not working again.
View 8 Replies View RelatedThe firmware update went smoothly The mydlink service quit accessing the camera, until I download and ran the updated Mac version of the "mydlink Setup Utility v1.0.06_07272011"Seems as if the camera is more stable; ping times are more consistently low.
View 2 Replies View RelatedDue to problems with the D view cam, I have reset my IP camera DCS-930L but I can't register the password, it says "There was a problem saving your settings. Press next and try again." I can't get pass saving password, tried all the previous passwords but none works.
View 2 Replies View RelatedI can't get my brand new DCS-930L cam to connect to my network by using the WPA / WPA2 encryption. Works ok wired, with WEP or with no encryption enabled. Red led is on the front. I've tested sw version 1.02, 1.03 and the latest 1.04b03. Same result: WPA doesn't work. I have a Thomson TG789 Gateway/Router as provided by my ISP. All other units in the network works perfectly fine on WPA i.e. PC, Mac, printers, mobile phones etc etc.
View 1 Replies View RelatedExcuse my ignorance but, is there an easy way to add the camera image's to a website Is this a process that utilizes FTP - or
I do have some experience creating websites using MS Front Page.
I've just successfully set up my network camera and as I was running through the advanced settings, what it wants from me when it comes to setting up images being sent to my e-mail. I've looked up some old threads to get a clue and thus far nothing works. Testing my entries results in "Invalid e-mail setting" 10 out of 10 times.
The setting format I'm trying to use is as follows:
-- smtp.gmail.com
-- 587
-- myemail@gmail.com
-- myemail@gmail.com
-- myemail
-- mypassword
-- STARTTLS
My GMail account is POP Enabled (whatever that is) and I used the username for that e-mail for bother the Sender and Receiver fields, as well as that e-mails username and password.
I'm lost. I bought the camera so I could document my landlord's maintenance people "touring" my apartment while I'm at work, but I wasn't aware having it save screenshots would be so complicated.
How can I change the camera name form the default which is the same as the model name
View 1 Replies View RelatedI just got a DCS-930L camera. I was able to set the password (10 characters) and complete the setup. It then said I needed to update the firmware which I did and it successfully completed. I was able to access it through the mydlink web page but when I clicked on the advanced settings, it wouldn't log in. I tried running the setup from the CD but it said "There was a problem saving your settings. Click Next to try again." That never worked. I tried a hard reset, no luck.
View 3 Replies View RelatedI have a DCS-930L network camera that I configured from its Web-based interface. In SETUP | Network Setup, I have disabled both UPnP and UPnP Port Forwarding. In my router's (Netgear WNDR3700) settings, I reserved the local IP address, 192.168.1.80, for the DCS-930L. In the DCS-930L I assigned the network camera HTTP Port 8000; therefore, I can access the DCS-930L on the LAN from [url].... In addition, in the router, I have forwarded port 8000 to the local IP address, 192.168.1.80, so I can access the DCS-930L from outside the LAN.I can access the DCS-930L both from within the LAN and outside of the LAN.
However, even though UPnP and UPnP Port Forwarding in the DCS-930L are disabled, the DCS-930L keeps adding and deleting UPnP NAT rules in the router. In addition, a system at the IP address, 207.232.83.172, keeps attempting to access the DCS-930L from different ports. I traced the IP address, 207.232.83.172, to the ISP, Telekenex, in Los Angeles, California. A partial log from the router is below.[code]...
Is there a way to reset the camera remotely, via the browser interface or a FTP connection? I can't find a "reset camera" button on the web interface...unless I've overlooked it.
View 3 Replies View Related