D-Link DIR-601 :: Mac Filtering Not Working

Oct 15, 2010

I tried to find an answer to my issue however came up short. Did find,url... but that for a 600 not 601. I have "Mac filtering on and to only ALLOW the addresses below" however, it allows any computer, even if i do not have them listed.

View 3 Replies


ADVERTISEMENT

D-Link DIR-655 :: Website Filtering Not Working?

Jan 17, 2011

It seems (and should be) pretty straight forward; under ADVANCED go to WEBSITE FILTERING and enter in the URI, or partial URI, that you want blocked and make sure the drop-down menu is "DENY computer access to ONLY these websites".  The only problem is, I can still get to all of them. I saw in another forum that you had to check "Enable Access Control" and go through a 6-step process where you specify machines - I truly hope that isn't the solution, because it's needlessly complicated for most users who only want to block ALL devices on their network from accessing certain sites. My Hardware Version is B1 and my Firmware version is 2.00NA.

View 2 Replies View Related

Linksys Wireless Router :: WRT610N URL Filtering Not Working

Aug 3, 2012

I am trying to filter a URL, facebook and it is not working.  I have tried rebooting the router and it is still allowing access.  I have provided the settings and ranges for PCs.

View 3 Replies View Related

D-Link :: DIR 500 Filtering Websites

Jul 12, 2012

I have dlink dir-600 router and I want to block access to website [ URL] for only one PC connect to router. i can either block web access to both PCS connected or block entire web access to one PC.

View 1 Replies View Related

Cisco Firewall :: ASA 5505 URL Filtering Using URL Filtering Server?

Feb 7, 2012

I have come across articles mentioning that URL  Filtering can be implemented by using ASA 5505 with URL Filtering  Servers. But Websense and other Web Filtering Servers are paid ones ?  Are there any free solutions available ? What exactly is N2H2 ? The  reason is I don 't want to increase the CPU utilization of ASA by  implementing URL filtering within the device. If I have around 30 nodes  which connects to the internet via a 2Mbps line through ASA 5505 and if I  want to block around say 10 or 15 URLs , will it increase CU  utilization beyond permissible limits ? Currently the CPU Utilization is  around 10 - 15 . Here's the infrastructure setup .

------------------------------------------------------------
Nodes -->Switches-->ASA 5505-->Internet
-------------------------------------------------------------

View 4 Replies View Related

D-Link DIR-655 :: Turn NAT And Endpoint Filtering Off?

Feb 12, 2011

My network is set up in the following way..

DSL-320B | Linksys E3000  192.168.0.0/24 Subnet A Static Route 192.168.1.0 255.255.255.0 192.168.0.100 | Wan Port 192.168.0.100 DIR-655 | DIR-655     192.168.1.0/24 Subnet B

I am unable to browse by IP any machines on Subnet B from Subnet A and suspect this is due to the NAT and the Endpoint filtering within the DIR-655.

View 2 Replies View Related

D-Link DIR-825 :: How To Enable SPI Firewall And Wireless MAC Filtering

Jan 23, 2013

Where on my router interface I could go to enable both the SPI Firewall, and the Wireless MAC Filtering? I have the D-link DIR-815.

View 1 Replies View Related

D-Link DIR-600 :: Doesn't Allow To Enable Wireless MAC Filtering

May 20, 2011

DIR600 doesn't allow me to enable wireless MAC filtering when I setup DIR600 as access point. (I connected DIR600 (access point) to my another room's router.)

View 1 Replies View Related

D-Link DIR-600 :: Configure Firewall UDP Endpoint Filtering?

Jul 10, 2011

 I would like to know how to configure my DIR-600s firewall UDP Endpoint Filtering. I ve read some guides and I ve got to configure this to Endpoint Independent in order to play League of Legends. The problem is that I can see the option Firewall & DMZ but then I don't see the UDP or TCP Endpoint Filtering options.

View 1 Replies View Related

D-Link DIR-655 :: Network Filtering / 24 MAC Address Limit?

Jan 23, 2013

I have had a great experience with my old DIR-655 (rev A) router.  However, I would like to upgrade to a newer and better D-link router for my home that contains many well-connected children. Which routers are like my DIR-655, and have better overall performance than the DIR-655 without necessarily using the benefit of the 5 GHz second band.   What better performing routers can record more than 24 MAC addresses in the Network Filtering area?  I understand many people don't agree with MAC address filtering, but I like it to keep my kids from giving out my network password to all the neighbor kids and their friends too.  So, MAC address filtering works for me.  Or, should I just get an updated version of the DIR-655?  

View 5 Replies View Related

D-Link DIR-655 :: Web Filtering Doesn't Work When Linked To MAC Address

Jan 5, 2011

My DIR-655:
Hardware Version: A4
Product Page: DIR-655

The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine? 

View 8 Replies View Related

D-Link DIR-825 :: MAC Filtering Blocks Allowed Devices After Several Hours

Jan 28, 2012

I have yet another problem now with the DIR-825.  I have a DAP-1522 that I connect my multimedia devices to like my TV, BD player, etc.

For added security, I use MAC filtering to only allow access to my devices that connect to my router.  However, after several hours, the devices connected to my DAP-1522 can no longer connect and neither can I connect to them.  The odd thing is that I can connect just fine to the 1522 itself.  I NEVER had this issue with the DIR-655 so I figured it had to be the 825.  After trying several things, I essentially narrowed it down to the MAC filtering.

If I turn MAC filtering off everything works fine all the time.  If I turn it on, everything works fine for several hours, even up to a whole day, but then eventually my devices can no longer see or be seen.

View 14 Replies View Related

D-link Dir-655 :: Mac Filtering - Only Want Wifi Filtered / Not Wired Lan Nodes

Mar 19, 2011

All 3 previous wireless routers I've had were all LinkSys routers and I had to overcome a learning curve since configuring this DIR-655 is slightly different..What I want to do is allow only the WiFi MAC addresses that I choose to access the network. It seems to me that in order to accomplish this I have to include all of my wired LAN devices' MAC filters as well. I can see having MAC filtering for WiFi devices, however why do I need to add my wired LAN devices MAC addresses?  I'm not going to allow just anyone to walk into my home off the street and plug a computer into the network via CAT-5 ethernet cable, so isn't there a way to accomplish just the WiFi allow list and the heck with the wired nodes?  The LinkSys routers I used in the past allowed me to allow the MAC filter for WiFi devices only.  Is there a way around having to allow all MAC's and just allowing the wifi's? 

View 5 Replies View Related

D-Link DIR-655 :: MAC Filtering / Network Filter And Guest Zone

Jul 22, 2012

207.NA Firmware, B1 Hardware in use on a DIR-655, Time Warner Cable setup.  Nothing to do with Revision, cordless phones,I saw this asked once before specifically here, but it was never answered.After several attacks via our cable network and neighbors, we've HAD to turn on MAC filtering.  There are TONS of devices attached normally so two situations popped up:

  #1:  What happens when you max out the authorized MAC address listings?  Does the page get longer when you save/reboot it?  Do I have to do it manually from there forward and where can I get down to the core programming level to edit the code and put the MAC's that are around and on 100% of the time to open up the plug-in list on the GUI?

  #2:  Guest Zone - we NEED a way to have random guests get on our Network with a different password we can randomly change to prevent the outside abuse, etc. but am I understanding what little else has been posted that the MAC filtering also covers the Guest Zone and therefore I have to stick them in there before they could simply log on with the current password?  Is there any way to change/stop that without eliminating MAC filtration as a whole?

View 4 Replies View Related

D-Link DIR-655 :: Enable Mac Address Filtering Only For The Wireless Side?

Sep 3, 2011

It shows this option "Filter wireless clients:   Apply MAC Filtering to devices that connect to the network via Wi-Fi. This is the normal usage of MAC Filtering. Filter wired clients: "However I don't see that option on the actual page. How can i enable Mac address filtering only for the wireless side?

View 7 Replies View Related

Cisco Routers :: RV082 Protect-link Activated But Not Filtering

Oct 7, 2011

I have a Cisco RV082 that doesn't appear to filter any selected categories. To run through what i've done so far, within the 'Web Protection' screen i've: enabled URL filteringconfigured a number of categories to filter by putting a tick in the repective business hours boxset the business days to 7 days a weekspecified business time as 24hrshit the save button. 

My licence appears as activated and my platform shows as "gateway service".I've gone on to a number of machines and all are able to access websites that fall under my blocked category (facebook for example even though i've blocked the social networking category).

View 1 Replies View Related

D-link Router Isn't Working?

Sep 27, 2012

i have a d-link wireless router model DIR-601 and all the lights keep turning on and off besides the power

View 1 Replies View Related

D-Link DIR-655 :: Limewire Is Not Working?

May 16, 2008

How to unblock limewire cuz its not working after i installed a DIR-655 at home.

View 3 Replies View Related

D-Link DIR-825 :: Bricked - How To Get This Working Again

Jun 6, 2012

I have bricked my DIR-825 when performing an upgrade of DD-WRT. Now I am not able to go on to the Recovery Web page. ( 192.168.0.1 ) after performing the 30/30/30 rule, wich always worked before.

I had done an update of dd-wrt and lost all of my wireless adapters, they said to load open-wrt, find the caldata and write this. This all worked. But after a reboot, the deviced bricked on me .

View 3 Replies View Related

D-Link DIR-655 :: Not Working After Upgrading From DIR 615

Jul 18, 2012

I just upgraded from DIR 615 to DIR 655.  I used the installation CD but I have no wifi signal detected.  Wired connection with 655 works though.  If I go back to 615, wifi works. 

View 1 Replies View Related

D-Link DIR-615 :: IP Phone Not Working With It?

May 4, 2011

I'm having problems connecting my ip phone with DIR-615.I got a plug and use ip phone from vocalocity, it's actually from the office where we also had the same problem and a the end we just changed to a different router coz we didn't have time to look for solutions, anyways i brought one of the phones to my house and plugged it to the d-link but it's not working.

View 12 Replies View Related

D-Link DIR-655 :: WAN Port Is Not Working?

May 19, 2011

Recently, something weird occurred. My Motorola Surfboard cable modem (on PenTeleData/Service Electric) and my D-Link DIR-655 don't seem to be getting along.If I plug a network cable directly from the modem into a computer, it works fine. However, if I go from the modem to the router's WAN port, it doesn't seem to want to connect to the router at all (no matter what DNS settings I change on the router (including spoofing the MAC address of a working computer) or which network cables I use; the "activity" light on both the router and the modem remain off).Also, if I take a network cable and plug one end in one of the LAN ports on the router and the other end in the WAN port, it works (well, the "internet" activity light on the front of the router comes on and the status page at http://192.168.0.1/Status/Device_Info.shtml says "Cable Status: Connected; Network Status: Incorrectly configured - check logs" instead of "Cable Status: Disconnected; Network Status: Disconnected").

View 11 Replies View Related

D-Link DIR-655 :: How To Get Web Logging Working

Apr 3, 2011

how to get web logging working? I set up an Access Control policy for web logging only for one machine on my network. I also turned Syslog on and have Kiwi syslogd running on my desktop. However, it's not logging web traffic. how to get web logging working correctly?

View 4 Replies View Related

D-Link DIR-615 :: Ver E3 Wireless N Not Working

Oct 17, 2011

I have Ver E3, with firmware 5.10.  Like it says above, Wireless N is not working.  I've already going into Manual Wireless set up and selected Mixed G and N.  All of my devices will connect, but only as G devices.I'm reluctant to set it to "N only" for fear that none of my devices will be able to connect.

View 14 Replies View Related

D-Link DIR-825 :: DIR-835 5GHz Not Working

Mar 14, 2013

The 5 GHz has been working for 2 months but now, no longer available. No visible 5GHz wireless network. Reset to factory setting and reinstalled but still no 5 Ghz. The 2.4Ghz is working fine.

Location Australia
fcc id: KA2IR835A1
IC: 4216A-IR835A1
P/N: IIR835NAU...A1E
S/N: QBKA1C5001387
WPS PIN: 24784784023
H/W Ver: A1 F/W Ver: 1.01

View 1 Replies View Related

Have A D-Link DIR-615 Router And Can't Get The Internet Working?

Feb 19, 2013

I have a D-Link DIR-615 router and can't get the internet working and have done everything possible to get it working. the globe light which is the internet light will not turn from amber to green. I have done a factory reset which is why this occurred in the first place. After the reset the globe stayed orange and the internet refused to work now everything is up but the wireless will not work nor the internet I have gone through both the manual set up and set up wizard and tried all options.

View 8 Replies View Related

D-link Router Has Stopped Working

Nov 11, 2011

I have been using a d-link router for some time now and since yesterday it has stopped working ( I have an orange 'world' light on all the time) After looking around this site I have tried resetting etc and nothing works. If I plug the ethernet cable into the modem I can get on the internet if I plug the cable into the router then nothing. These are the details I got from the config all when I plugged the ethernet into the router.

View 3 Replies View Related

D-Link Wireless Adapter Not Working?

Mar 3, 2011

I have a D-Link wireless adapter (DWL-G122) that I have been trying to install on a Windows XP computer. After various uninstalls and reinstalls of the drivers and programs that come with it, I have found currently the best way to get it to work is leave the D-Link programs uninstalled and have Windows install the driver itself.The problem is, it doesn't seem to keep the drivers on restarting, so every time the computer is restarted, it must be installed again. This is not ideal.It occasionally worked when I installed from the CD, but the D-Link programs that would install with the drivers created problems of their own.

View 2 Replies View Related

D-Link DIR-625 Router Stopped Working?

Jul 10, 2011

My router suddenly stopped working yesterday and I've tried everything I can think of to fix it. I have one computer wired directly in to it and a few laptops that use wireless connections.The power LED and the internet LED light up, but the status LED and the WLAN LED do nothing. Pushing the factory reset button on the back doesn't seem to do anything.Can't connect to the router site (192.168.0.1) The internet works fine when I plug in to it directly, so its definitely the router.

View 3 Replies View Related

TP-Link TL-WR841N Not Working Properly

Jan 29, 2012

I bought a TP-Link TL-WR841N which i have managed to setup up properly, i am able to connect to the wireless and get internet access. However the minute i walk out of the room or a few meters away i am disconnected and i can't re-connect, i get the "windows cannot connect to TP-LINK" message. The signal strength in on excellent and i know it works because when i stand near it, it works perfect.I phoned TP-LINK technical support who were pretty useless and couldn't fix the problem.

View 3 Replies View Related

Wifi Not Working With Tp-link Router?

Jul 20, 2012

im deployment and we have hardwire internet in my room. wanting to use all other devices eg. iphone and what not i bought a router to plug the hardwire in to and run the wifi off the router for all devices. its made by TP-LINK the model is TL-WR940N. it worked great for a while but then kept giving me DNS server is not responding but i could plug the hard cable in my computer and the internet would work fine? so i reset the router and set it all up again like before. Now i cant get it to run wifi off it anymore it recognizes and connect through wifi but no internet and its telling me i need to plud the hardwire in to my internet but my computer is recognizing it and saying i have internet access, but no internet i mean its not even thinking if there is internet.

View 1 Replies View Related

D-link Dir-655 :: How To Know If Wifi Antenna Is Not Working

May 7, 2011

I have a Dir 655 router how can I know if one of the antennas is working right? 

View 5 Replies View Related

D-Link DIR-655 :: ITunes Remote App Not Working?

Feb 5, 2011

It worked fine with my last router. It just doesn't seem to connect securely. It comes up under my iTunes, but once I go to enter the code, it doesn't show up as completed. Also, a utorrent monitoring app cannot connect to my computer, which is set up right at my computers end, but won't connect at all from my phone over wi-fi.

View 14 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved