D-Link DIR-615 :: Connect 2 Wireless Modem Routers + Switch In Home Network
Nov 14, 2011
I have 3 pieces of hardware:
1. Green Packet DX-230 WiMAX modem with router
2. D-Link DIR-615 ver G2 (from my ISP)
3. D-Link 8 port desktop switch
I previously used the DIR-615 with my high speed broadband connection. However I had to move to a new house and here I can only get WiMAX. I want to...Place the WiMAX modem upstairs to serve as modem and wireless access point Have the DIR-615 function as the main router and firewall (downstairs) Use the switch to connect all the rooms in my house FYI my WiMAX modem has no connection configurations. I just plug it in and it'll connect automatically to the WiMAX signal. It has 2 LAN ports but no WAN port. From my understanding of networking, I have to turn off DHCP on my WiMAX modem, put it in the same IP range as my DIR-615 (192.168.0.100-199), and disable UPNP and NATPMP. After this I'm stuck.How do I tell my DIR-615 to use the WiMAX modem as it's WAN connection?Should I reserve an IP for the modem in my DIR-615?
I have Zyxel Modem configured in bridged mode with static IP from ISP. I want to connect multiple PCs to modem via switch so that each PC use the same configured Public IP address to use the internet. For this (generally) I would need to configure NAT for that IP. But I want to know that will it work under bridged mode or not?
Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
I'm having trouble connecting my 02 dongle to the internet using my router. My router is a TP-LINK MR3420 and my 02 modem device is E1752. I checked to see if the modem is compatible and it says it is. I went through the configuration that was given to me with the router and I tried using you tube but nothing. Do i need to get a static I.P address off my Internet provider? If I plug my 02 usb dongle directly into my computer it works perfectly and I got the router to work using a ethernet cable and plugging it into the WAN port at the back of the router but I would prefer to let it connect through the 3g port. I get a connection at 40% and 100 bytes are sent and some are received but the connection drops. Is it a problem with the connection? I will upload a image.
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
i have triple storey house. in all three floors a broadband connection point (rj45 jack) is there. i have connected one wireless router in 3rd floor. but the signals are not coming on second floor. can i connect netgear wireless access point with one ethernet point in the 2nd floor broadband connection jack (Rj 45), to access wirelessly my internet?
I have 2 wireless routers. Belkin Wireless G plus mimo Model# F5D9230-4 Ver.3001 and a D-link Dir-615 ver.B2. I am using the Belkin router has my main router. The wife’s laptop and the Wii console connect to the router wirelessly. I also connect a few PC directly to the router via Cat5 cables which runs through most rooms in the house. Since the router is down in the basement in my control panel along side the cable modem and what not. This causes the wireless single to be pretty weak in certain parts of the house. What I was planning on doing is taking the D-link router connecting it to the wall jack upstairs to the internet port on the router. Then setting both routers to static and changing the Belkin router to DHCP?
I finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
is it possible to connect the wan port of a cable modem to a lan port of the home network? the reason is, i need some wifi access and more ports to my wired network, and the most reasonable solution would be a cable modem router with wifi and 4 ports just plugged into one of my routers.
My use case is very simple I want to connect iPhone/iPad using pptp to my home network. I purchased the 180W and looks like I am not able to connect mobile devices to it. My Setup is simple I have ST536v6 (firmware 7.4.4) modem in bridge mode and Cisco RV 180W connect to my ISP using Ppoe. I followed the Admin guide and created the pptp user. If I connect from internal network it connects but when I try to connect the device from WAN it just does not work.
I had Symfony modem with Asus ap and 1 d-link switch. i changed my modem because that was old and bought TP-Link(TD-W8961ND).It is connected to the Dlink switch and the switch is connected to the Asus Ap(RT-N12) The situation was the same just modem has been changed. Now i have this problem: i have internet with cable every where...behind switch or behind Ap...but when i wanna use internet with wireless via Asus Ap it doesn't work i checked every thing...the Asus Ap has 3 mode(Ap,Router,Repeater)...i chose every one but only repeater mode works. by the way with modem wireless i can get to the internet but the signal is fair for me to use!
I have two netgear wireless modem / router. I want to connect my internet, NAS and Media player on one device (netgear modem/router) and want to link the other netgear in my bedroom and connect another media player and also use the internet via primary netgear modem/router wireless connectivity.
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
Our desktop is connected to a cable modem and I always connected wireless with my laptop. When I changed my linksys wireless adapter I tried to get on the internet and it would not connect to the linksys router, so I then do not know exactly what I did,but the result was that i finally had a connection. That was a month ago and I finally looked at the network mapping after I noticed the desktop was on a lan network and the cable connection was flagged. Apparently, I created something called a switch with the router and now I have a whole new network in my name that has the cable connection.
I'm experimenting/attempting to use a laptop as a network tap between my (DSL) modem and a wrt54gs by creating a bridge with two NICs in the laptop. My problem is I can't seem to get connectivity on the user end of the router. I can't ping the bridge from an end computer...
DHCP is disabled in the router, but even when manually configuring the IP address on an end computer and using the bridge as a default gateway I can't ping out.
Am I completely misunderstanding the purpose of a NIC bridge?
so yesterday I went out and bought a new Cisco Linksys E4200v2 router. My ISP is Communicomm (terrible, but they're the only one here). I also have a Terayon TJ 715x cable modem. I shut down pc & cable modem, connected everything, and powered back up. I am able to access the router config page at 192.168.1.1, but the router does not receive an ip address from the modem. If I plug the modem directly to the pc, I get an ip and am able to connect to the internet. I have called my ISP several times, and they tell me that they do not use MAC address filtering. The only MAC address that they need is that of the modem, which they have. This modem has been working fine for several years. After spending over an hour on the phone with Linksys support, they have determined that the router is functioning properly.I also tried hooking up an older netgear router and got the same results. The following is my ipconfig with the modem connected directly to the pc. [CODE]
I am in the process of opening an internet cafe. I dont know exactly what a pc server does on the network... or do I really need one? Is the switch/hub sufficent to connect all pcs to the moderm to connect to the internet?
everything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
Region : UnitedStates Model : TL-WR841ND Hardware Version : V8 Firmware Version : ISP : optimum online I have two wireless routers: TP Link TL-WR841ND and TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones. I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings: Firmware Version: 3.13.27 Build 121101 Rel.38183n Hardware Version: WR841N v8 00000000 WAN type: dynamic IP LAN IP address: 192.168.0.1 subnet mask: 255.255.255.0 DHCP Server: enabled Start IP: 192.168.0.100 End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
I have a wireless modem on the first floor of my house, where I got cables through the wall running throughout rooms in first floor, ground floor and basement.I have my small business at the basement, so I have 2 PCs one printer and one external hard disc which also connects directly to a modem/router.I have 3 PCs from the first and ground floor that connect through the wall to my modem, and everything works well. But for my basement, which only has 1 lan cable output on the wall, I got myself a router so that I can connect all my devices.I connect the router with my modem, and then the PCs, printer and hard disc on the router. The PCs have internet access, so I know the connection to the modem has nothing wrong to it. But I am not able to access the PCs connected to the router from the PCs connected to the modem, or vice versa.
I was told to not obtain an IP address automatically, so I assigned my modem and router to work on 192.168.10.x and gave my PCs IPs such as 192.168.10.19 Only after setting this up did all my PCs have internet access, but again, no network communication between PCs on modem and PCs on router.One thing that might be worth mentioning, is that through time, my network keeps going from Home Network: Network, to Network 2, Network 3, and so on... now it's on Network 5. I have no clue why this happens, and if it's related to my problem
What I learned was it was bad to connect directly to the modem because you are left open to the internet. Currently my friend just got the internet and I told them to buy a router but they did not, and just have it directly connected to the modem. Is this fine, because they only have one computer, and it works fine for now, but wouldn't this be prone for attack?
My Wifi network has a wpa2 password that is a random string of characters and numbers and yet last month a rogue IP Address kept popping up on my DNS list. It has to be coming from my neighbor who's bedroom is about 15 feet away from my router. So unless someone is sitting out on my front lawn to do this then it must be him.I've been looking for software that will notify me when a connection my router is attempted and kudos if it also asks my permission first would be great.There are wifi packet sniffers out there like Cain&Abel, Airsnort, that sort of thing but I am not quite savvy enough nor do I want to turn this into a complicated hobby but just need a basic warningin case something gets past my passwords again
my computer will connect wired to internet and can find the wireless connection but wont connect. my wireless icon flashes intermitently and my mobile will work via wifi. do i need a new router this one is a G wireless Modem router Belkin had it for about 4 years?
I recently decided to buy a DIR-655 router to create a wireless network in my home. I hooked it up last night and speeds look fine with my rr standard 10mpbs service. However, I decided to check the wireless status and my macbook, macbook pro, and my desktop computer are only getting at most 130mbps. Is there anything i can do to maximize this and go beyond 130mbps
I think that my ISP is throttling my bandwidth at the modem . how access full available bandwidth.When the technician installed the fibre optic line and then the modem, he showed me an amazing 77MB/s (about 600Mbps) before the modem!!But after the technician left these were the test results after the router:
averages, after router, show: UP between 56/60Mbps & DN 45/75Mbps
2)Local Server Speed Test:
average: UP 45Mpbs & DN 170Mbps
A Japanese Internet savvy guy explained that NTT East throttles the available bandwidth at the building by specific apartment/modem settings related to individual contract bundles. I signed up for the top bundle: TV, Phone and Internet connections.This is my Hardware/ software setup:
Line specs: Line type: IEC60874-14 Connector type: SC Core across: 9 micrometers Clad across: 125 micrometers ITU-TG-652 NTT East fibreoptic TV/Internet/Telephone bundle (100Mbps best effort) Hikari Next Family Type but 10Mbps is considered within parameters Asahi ISP Internet contract
Modem: GE-PON (WAN+Coaxial TV antenna) "SCM-GE-PON-<H>A GV-ONU D<1>" model
Router: RT-S300HI (4 Giga ports + 1 phone)
Router & Modem have Japanese firmware which I cannot understand and, according to the NTT East, I must rent both modem and router from them and "will not support any other modem/router setup".I could not understand if it was because of technical or contractual limits.
I have tried to test my throughput after the modem but I could not figure out where the DNS, IP, WAN etc strings of numbers should go and, in the end, I simply cannot connect to the internet from my laptop directly to the modem so I cannot perform the same speed tests after the modem.
I've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
I have a TP-Link TD-8616 modem and TP-Link TL-WR740N wireless router. Both are ADSL compatible. Each time I tried to connect with the wireless router I will no longer have internet service. Teksavvy is my internet provider. how I can get this to work.
At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.