D-Link DIR-615 :: Runs Very Slow And Losses Connection Or Will Not Connect At All
Jul 19, 2011
I have had this wireless router for 3.5-4 months, and it has been working fine up until now.It either runs VERY slow and losses connection often or will not connect at all. I could be sitting beside the router or across the room with the same results. i have even tried connecting a cord from the laptop to the router, but it makes no difference. If it makes any difference we have a PS3 that is connected via wire to the modem and it works just fine, never loses connection. We have used both at the same time since we got it and it was fine up until a few weeks ago.I have tried reseting it and unplugging everything and rebooting the computer and that had no effect. I also tried reinstalling the router on the computer using the setup disk and resetting everything but that did not do anything either. I have an Acer Aspire laptop MTS ~ DSL Modem?
View 4 Replies
ADVERTISEMENT
Apr 10, 2012
I setup sharePort today and attached an external 1 TB hard drive. Seems that All my internet connections are slow now. I have a seperate PC that I use VPN to connect to work with and suddenly its very slow. My wife said her laptop suddenly slowed down too. The PC that I installed SharePort software seems slow too. Is/can SharePort be dragging down the router? I turned off the external HD and it's still slow.
View 14 Replies
View Related
May 10, 2012
I have a D-LINK DIR-300 router with 4 LAN and WI-FI. It's acting very strange lately. It is connected to a UPS battery and the one LAN connection is in surge protection.Here are the symptoms:
-Every 2 days it just loses connection. I have to reboot it so to make the connection working. It's a little bit annoying after awhile.
- One day one of the LEDs started like fading away and came back up (the one that signals the LAN connection).
- When all the LEDs were properly working and the connection was good also, I moved the the power adapter cord a little bit at some part (I didn't plugged it out) and some of the LEDs gone (Internet connection LED and Wireless) but all the other LEDs were working. Of course there wasn't connection either.my OP is Ubuntu 12.04 and the connection DHCP is well configured.
View 1 Replies
View Related
Dec 26, 2011
I have a D-Link DIR-615 Hardware Version: E3 Firmware Version: 5.10 and I am using this as an access point with the DHCP disabled (secondary router) and my primary router is located down stairs and it is also a DIR-615 Hardware Version: B2 (192.168.0.1) and this issue didn�t develop until later over time and I have made absolutely no network configuration or ISP changes at all the internet has been working fine confirmed with Time Warner Cable and for more than six months and I out the DIR-615 Hardware Version: E3 Firmware Version: 5.10 router has been bringing down the entire network/internet access and I can confirm this router is causing the network/internet to go down and windows notification will say the network only has limited access and I am also unable to access the router page (192.168.0.2) state I have to remove it and restart it D-Link can take a look into this issue I believe this might be a bug and I confirmed on the website that this is the latest version.
View 15 Replies
View Related
Feb 14, 2012
I'm having WIFI connection issues with a Sony Vaio VGN-FW140E Laptop. After a connection is established it will randomly stop working.The network adapter is a Intel WiFi Link 5100 AGN using driver version 14.3.0.6,I have also tested the connection with a Cisco Valet AM10 WIFI USB adapter and received the same results.All other devices connected wirelessly are not experiencing any connection problems.
View 2 Replies
View Related
Jun 9, 2012
I've got a new PC which is now about 4-5 weeks old. It worked great in the first 2-3 weeks, but then the network connection started to be unstable. That means that the connection is lost regularly (in intervals between 15 seconds an several minutes). After it is lost there's an immediate reconnection attempt, which usually is successful. So the connection downtime is mostly inbetween 2-10 seconds. Now that does bother me pretty badly. Especially in online games this leads to many disconnects or lagspikes of up to 10 seconds.
The connection losses always come paired with DPC latency spikes.I switched the LAN cable just to be sure. I updated all drivers (including BIOS). I deactivated all eligible components in the device manager one by one. The only thing I found out: If I disable the network adapter, the latency spikes are gone. But that doesn't work because the connection is gone too. For that network adapter I tried different drivers, various versions from Shuttle and also the latest original driver by Realtek.
View 2 Replies
View Related
Dec 25, 2012
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have two(2) WR941ND routers working at my home. The primary has IP : 192.168.1.2 , this primary router is working as an Acess Point, DHCP is OFF, and no wireless security activated. This primary router is connected to a DSL modem+router and DHCP is activated on it.For the secondary router I configred 192.168.1.100 . On the secondary router I have activated WDS function as well as Wireless Security (WPA2) , DHCP is Off on it. This secondary router is to work as wireless bridge + Access Point. You will understand that this secondary router is wirelessly connected to the primary one.I am able to configure all, and all things work correctly for few days at a time.But if at any time the secondary router is switched OFF, and then again switched ON, it seems to have lost al the settings and its IPs, and thus unable to connect to primary router. At such time I am unable to locate /connect my laptop to this secondary router, and it keeps on searching & searching.
View 1 Replies
View Related
Nov 4, 2011
I have a net gear WNR2000vs with the latest firmfware to date.wired devices connected: 1. my pc 2. xbox, and also one wireless device connected to my cell phone via wi fi.
View 9 Replies
View Related
Jul 29, 2012
I have a Linksys Wireless-N Home Router, WRT120N to be exact, and I have been having problems with my wireless. My wifi losses internet connection intermittently. This does not happen when I am connected directly to the router with a Ethernet cable. I have redone all the settings many times(like 6) and Im still having the same problem.
I really dont want to have to buy a new router
View 8 Replies
View Related
Aug 6, 2011
I need to know why I am losing internet connectivity like around nighttime, late. I keep losing internet on both IPv4 and IPv6! It both said "No Internet Access" Then later IPv6 said "No Network Access" That's the problem i am having on my personal laptop computer. I really am furious that I lost internet connection around 12:15, 12:30, 12:50, 1:30, 2:15, 2:30, and 3:30 A.M. i suddenly lost internet right there. And I heard the internet crew shuts down the internet system every nighttime and fixing it. I want to know why they need to fix it, how long will the repairs last ?
View 1 Replies
View Related
Nov 6, 2011
Every now and then my adapter won't be able to connect to the internet for a few minutes, and then it just comes back. This happens frequently, varying from every few minutes to every few hours. If I re-connect the adapter, though, a connection instantly comes back. There's no sign that it's lost connection, the taskbar still displays Internet access and a 5 bars, and the blue light on the adapting keeps flashing; but I just can't connect to the iternet at all.
View 1 Replies
View Related
Oct 20, 2011
wireless connection stop working and icon lossed on hp laptop dv 2000
View 1 Replies
View Related
Nov 8, 2011
Yesterday, my linksys router broke down suddenly. I went to the store and bought a new one, a d-link DIR-615. After plugging it in and setting it up, i tried loading web pages and it worked ok. It wasn't as fast as my linksys router but it was fine. When i tried loading youtube videos, that wasn't the same story. The videos didn't load. It started playing but then stopped after a couple of seconds. When i connected my computer directly to the modem, the videos loaded fast. There seems to be something wrong with the video streaming.
View 9 Replies
View Related
Mar 21, 2012
Recently replace my DIR-615 (it died after about 3 years of steady use) with the 825.Followed CD setup wizard, adjusted some manual thing as well. Am experiencing slow streaming speeds on various websites. A lot of 'loading' pauses within a youtube video for example when I never used to have any stutter at all on my old router.On a cable internet connection with a standard cable modem (no router in it).DIR-825 FW: 2.06NA HW: B1.Wired connection to router, not trying to steam over wireless.Speed tested at 14Mbps down which is what my provider (cogeco cable) promises.
View 1 Replies
View Related
May 6, 2011
Having some issues with my wireless connection which only seem to occur after 12-1AM, my signal according to windows 7 seems be lowered which results in anywhere from 2-10 seconds stall in service, sometimes even disconnecting me all together.
I get no issues during the day of any sort where i have 4+ other devices constantly using the router but I'm the only person in the house that uses the internet this late in the night so I'm completely stumped on what the problem could be.
Using the Dir-655 router with B1revision with 2.0 firmware, connected with an older wireless G adapter.
View 9 Replies
View Related
Apr 2, 2012
Last week I upgraded the firmware to 1.13NA and ever since, the wireless network has been slooooooow (wired is fine). If the laptop/ipad/phone is in the same room as the router, things are fine. Anywhere else in the house, the speed drops off to almost nothing even though the signal strength is very good. For example: Under the "Speed" section of my "Wireless Network Connection Status" on my laptop, I'm seeing 150.0Mbps in the same room as the router, 25.0 Mbps in the hallway and 1.0 Mbps about 5 steps further away. All the while, the signal strength is showing Excellent.Speakeasy speedtest: Wired 23.36 Mbps, wireless at the end of the hallway, .12 Mbps.
Hardware version: A1
Firmware version: 1.13NA
Cicso Cable modem DPQ3212
View 5 Replies
View Related
Aug 19, 2012
I originally installed my DIR-655 as a wireless access point, not using the wired ports at all, and it worked fine like this. Trouble with my trying to set up my Bell router/modem with port forwarding prompted me to change my configuration so my Bell router /modem is now only a modem, and I am using the DIR-655 as a wired as well as wireless router. I have a separate network server and so don't use the DHCP on the DIR-655, and I only use one port to connect to a separate gigabit switch that serves the network.
I am finding that the wireless connection works really well with the few wireless devices I have connected (mainly an apple tv, and a MAC book) but my wired connections to the internet "feel" slow, sometimes with a significant delay before links to sites are established. I click a link, and wait for several seconds before the site shows up in the browser; sometimes after that the same site seems to respond at normal speeds, other times there are added delays.
Is there something in the DIR-655 settings that would cause this? The wireless connections seem fine.
Should I be looking at a new router/modem (rather than separate boxes)? If so what would be the equivalent D-Link model?
View 5 Replies
View Related
May 11, 2011
This only started about a week ago and everything was working fine before then. My router is causing my internet to be slow (I know this because it goes at normal speed when I am connected directly to my modem)
View 1 Replies
View Related
May 7, 2011
I am using Comcast as an ISP and have a standalone Arris modem. I, obviously, have a DIR-655 router REV B with a firmware revision on 2.00NA. I have already turned off packet shaping and QOS. Also, I have set the firewall settings to Endpoint Independent for both TCP and UDP, and assigned static IP addresses to my computers. The problem I am having is that whenever I go to any secure websites, i.e. anything that starts with https, it takes an extraordinary long time to log in and to navigate to any webpages therein. I also cannot upload photos to a website and when I try the Speed-test.net website the download speed is OK but the upload test errors out, it doesn't connect.
View 2 Replies
View Related
May 11, 2011
I just bought a DIR 615 (firmware 4.0) which I am using as an access point linked to a Netopia router. The Netopia has QoS enabled and needs to keep it, however I was hoping to use the DIR615 without QoS. I am using a ReadyNas Duo as storage for music, videos etc.Now, here are my issues which I think are all linked.
1) I have a very slow connection wireless, between 1'500 and 2'000kbits/sec download. This was not the case with my very old Linksys router
2) When I try to rip a CD from iTunes to the NAS, it brings up error messages of lost connection and impossibility to rip in the middle of the songs. I did not have that problem with the Linksys router neither.
3) I would like to change the QoS parameters to see how it affects this connection issue, as well as change other Wifi parameters, but they show up as greyed out and I can't change them. (I feel that the DIR 615 might inherit some parameters from the main router, since it is used as an Access Point).
View 4 Replies
View Related
Apr 24, 2013
Region : Malaysia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.13 Build 120605 Rel.38634n
The connection is slow when I connect my notebook to the TP-Link TL-WR1043ND wireless router. If I connect my notebook directly to to the ISP modem, the connection speed back to normal.
View 1 Replies
View Related
Jan 23, 2013
Region : UnitedStates
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.10 v0005.0 Build 120516 Rel.45877n
ISP : HiPointInc
Network Status.jpg
I've upgraded my line connection from 4mbps to 20mbps.I've also checked my status with HiPoint and on 192.168.1.1 which is shown on the attachment. No problems.
Max Downstream is 25612kbps but Current is only 4396kbps.Do I need to configure anything? Btw its directly connected to my PC?
View 2 Replies
View Related
Oct 11, 2012
Turn SPI under (Advanced/Firewall) off (uncheck the box).
I was getting slow page loading on Google Chrome and I think IE but don't remember for sure.
Once I unchecked the box for SPI, pages loaded much faster and I didn't have to double-click on links.
View 1 Replies
View Related
Apr 14, 2013
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Netherlands
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : Ziggo
I currently have a issue with my TP-link WR941N.When I first connected the router I had a good internet speeds of about 70 mbps. My max provided by the ISP is 120Mbps but 70 was acceptable for me. Recently however the connection is terrible. I regularly have a speeds of 6Mbps via the router, When i directly to the modem via kabel I get a speed of 120Mbps. Therefore I ruled out that the connectivity problem is due to my ISP.
View 1 Replies
View Related
Oct 20, 2011
I have pretty much the EXACT same issue. Revo 3700, Sky Unlimited Broadband, and a bunch of laptops and phones that can connect to the internet anywhere in the house without a probleI had the Revo connect all day last Friday (for the first time), prior to that it had connected a hand full of times, but only a very slow connection. For the last 4 days it hasn't connected at all, but says the signal strenth is 4 or 5 bars. I'm typing this from right next to the Revo on my laptop without any issue.
View 4 Replies
View Related
Mar 27, 2013
Region : Belgium
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Telenet
I've just bought a TP-Link TL_WR1043ND and when I was configuring the wireless settings first I had a +- 40Mbps connection,a little later the connection dropped to 4Mbps and was constantly dropping the speed.Sometimes it went to 15Mbps and then it drops back to 4Mbps.Right now its only 1Mbps.
Configuration:
Wireless channel: 11
Mode: 11bgn mixed
Channel width: Auto
Max tx rate: 300Mbps
Wireless router radio and SSID broadcasting enabled
[code].....
View 1 Replies
View Related
Sep 18, 2012
I have recently had trouble with my wireless D-link WBR-1310 Router. Two days ago everything was working fine, my wireless connection from the router to my macbook was fine and the wired connection to my desktop pc was also fine. I went to bed and when I woke up the next day everything was still ok. About 3 hours after I had first turned on the PC that next day my wired connection started spiking and dropping connection frequently, maybe every 5-10 minutes or so. I play world of warcraft and I also use Mumble VoiP Program and my pings in both are over 800 constantly now making it impossible to stay connected to either program. Sometimes it will drop down to regular numbers (25-50ms, I play on eastern servers as I am in NY) but then rapidly jumps back up into the 1,000's. My wireless connection is still fine though nothing has happened to that, only my wired connection is messing up.
I've tried changing my speed and duplex settings on my onboard NVIDIA nForce 10/100 Mbps Ethernet which is what im using but it hasn't worked. When connecting directly through the modem the problem seems to stop so its definitely the router.
Wireless Router: D-link WBR-1310
Hardware Version: B1
Firmware Version: 2.02
[Code]......
View 2 Replies
View Related
Jun 28, 2011
I have purchased a new home where cat5e was run from several locations throughout the house to the basement. Unfortunately, the runs were not marked. I know you can short one end of each cable and measure (voltage resistance?) at the other end in the basement to identify it. I need the process and equipment required so I can wire my home. The cables are not terminated.
View 11 Replies
View Related
Sep 14, 2012
I have a server at work which an ESX server, it is running 5 VM's/OVA's and i have 2 physical workstations all hooked up to a switch. All the IP address's within the VM's/OVA are in the range 192.168.99.xx and so are the two individual workstations, they all need to be in that range to be able to communicate with each other.
View 2 Replies
View Related
Mar 27, 2012
Have a ZyXEL 600 wireless router - it has worked without issues for years.However yesterday evening my wireless router suddenly stopped broadcasting a signal. 2 different PC's and a wifi dongle attached to our TV were suddenly all unable to find my network.The WLAN light on the router was still lit up. I connected my Acer Aspire 5742Z laptop to the router via an ethernet cable and it worked fine. I connected to the router and it said there were no errors.
View 14 Replies
View Related
Apr 7, 2011
I have two 4503 switches connected individually two 5510 Asa. My web server is under 5510 dmz interface. From Two 5510 Asa dmz interface there are two cables connected to two individual server farm switches.The web server in connected to this server farm switches.My local lan in connected to a cisco linksys switch. from that two cables are connected two individual 4503 switches on same vlan. i configured hsrp on this vlan. i pings the web server from local lan. when i unplugged one cable from Primary switch then it take 7-8 request timeout to recover into Secondary switch. it takes about 40 sec to switchover. it takes too much time. i also tune the timers but no luck. My Primary switch is also a Root Bridge.
View 7 Replies
View Related
Sep 24, 2011
I Just got FIOS internet at Home with 43 Mbps down and 32 up (measured speed). I replaced the included router with my old reliable RV042 (V1) VPN router that I used with my old service in NY LI. This has been working very stable for week or two, but I use my old 042 to remote desktop via VPN from my work, that was limited to maybe 9-10 Mbps (Home to office) way down from the 32 up I have now (the office has 80Mbps down). So I researched that the RV220W had a VPN speed that was much faster and I ordered one that I am trying this weekend.Out of the box, I plugged accessed and just clone the MAC at the WAN port to match the replaced FIOS router. Power cycle and surprise, no IP from FIOS!. After trying a number of things, I gave up and updated the firmware to the last 1.0.2.4, and that fixed this. I still need to clone the MAC to void calling Verizon FIOS, but at least I get IPs and Internet with no trouble.Next, I configured a couple forwards for two web servers. I found about the bug in this same forum and just used the rules instead. Working good so far.
So now I test WAN bandwidths, and I found all kind of trouble. With the old RV042 and similarly to the included Verizon router I can do steadily 43d/32u. Especially at night is quite stable in these numbers. When I went and move the cables to the RV220W (exact same set up) the speed went all over the map from 4d/8u to 43d/25u. If I power cycle the box, things tend to be stable again around 43d/25u. So, after a while being stable in these numbers I start trying things to improve the 25u that should be around 32u, and recover the missing 7 mbps. Not much I can think, so I just randomly enabled the QoS settings trying to reserve full BW for my tests, and I found just that enabling WAN QoS, and nothing else, no profiles or changes in the Priority Settings, I go up to 30u consistently over a number of tests. This do not affect the down speed that is stable at 43 mbps. The surprising thing, is why this affect to the up speed when nothing else is going on in my network? and also where are the other 2 Mbps to complete the 32 Mbps that I can do with the RV042 (V1) or the cheap included router? In my opinion, if I don't use QoS, I should get full bandwidth to whatever application/computer that requests so, period.
View 1 Replies
View Related
Mar 22, 2012
ASA has 3 interfaces: outside, inside, DMZ Average total throughput is between 20-200mbps. Majority of throughput would be between inside and DMZ interfaces. CPU never goes above 70% (and doesn't seem to spike much with respect to traffic patterns).We are seeing lots of errors on the interface. Inside output:
Interface GigabitEthernet0/1 "Inside", is up, line protocol is up
Hardware is i82546GB rev03, BW 1000 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), Auto-Speed(1000 Mbps)
Input flow control is unsupported, output flow control is unsupported
[code]....
The ASA is a VPN headend for 3 remote branches. Approximately 100 VOIP phones between the sites register to a phone server at the main site (where 5520 is).I'm baffled by these overruns and underruns.
Code version 8.2(2).I refuse to believe that I need to upgrade the firewall when a 5520 can supposedly process 450mbps (aware this is best case but our average is close to 80-100mbps) and should do 300,000 bps wheras on average we are pushing 10-15,000.Is there anything we can do to find out why the ASA is having such a hard time processing all of the packets we are sending it?
View 5 Replies
View Related
