D-Link DIR-615 :: Static Routing - No Option For LAN Interface
May 11, 2009I have a DIR-615 rev C with firmware 3.10 and am trying to setup static routing. There is no option to select LAN for the interface
View 7 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 4507 - Dot1q Encapsulation Option Not Showing Up Under Interface
Jun 9, 2012I am trying to configure a 4507 R chassis with Dual SUP but i cannot see teh switchpot mode trunk encapsulation dot1q?
I have typed:
interface GigabitEthernet5/1
description DOWNLINK toxxxxxx
switchport mode trunk
channel-group 11 mode on
!
I have have searched all other commands and sub-commands but could only find dot1q-tunnel which I beleive is for QINQ or some QoS featues and lot for L2 encapsulations?
the puzzling is:
XXX-Core4507#sh int gi5/1 trunk
Port Mode Encapsulation Status Native vlan
Gi5/1 off 802.1q notrnk-bndl 1
(Po11)
when I connect the dostribution switch a 3507 to this int gi 5/1, both interfaces do come up?
Cisco Switching/Routing :: 6509-E / Unable To Perform (ip Nat Inside Source Static Tcp Xxx Interface)
Jan 21, 2013Platform:
cisco6509-E with FWSM
Supervisor Engine 32 PISA 8GE
sup-bootdisk:s32p3-adventerprisek9_wan-mz.122-18.ZY2.bin
command:
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
(config)#no ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
#clear ip nat tran *
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
%Port 14029 is being used by system
Or %Static entry in use, cannot change
But when I perform "sh ip nat tran" command,There is nothing
D-Link DIR-628 - Best Option For Homebrew Wi-Fi Repeater?
Mar 11, 2011My D-Link DIR-628 is at the far end of my house (next to my desktop and cable modem) and my PS3 and laptop are at the other end of the house in my living room. I'm not sure what's in my walls but it is NOT WiFi friendly!
[code]....
So I was thinking about buying a cheap N router and flashing it with DD-WRT and putting it in the living room.
I'd like this 2nd router to:
(a) Plug into the PS3 thereby "upgrading" it's crappy wireless card to something faster
(b) Have it act as a WiFi repeater to boost coverage on the far side of the house.
So is this going to work the way I'm describing it here? That's my current understanding based on what I've read, but I want to make sure I'm not missing something before I order the hardware.
D-Link DCS-942L :: Getting FTP Option To Work With This Camera?
Jan 18, 2012Has anybody gotten the FTP option to work with this camera? And if so how did you set up the path to point to the ftp share. The instructions say one thing but that one thing doesn't work. FTP is setup locally on my NAS box which does work. Or is this another one to add to the Firmware which list?
View 4 Replies View RelatedD-Link DIR-655 :: No Guest Zone Option / Need Firmware Update?
Jan 19, 2012Have DIR-655, HW A3, F/W 1.10. On the Advanced tab, there is no Guest Zone option. Can this be fixed with a firmware update? If so, which one?
View 2 Replies View RelatedCisco WAN :: 7062 PAT With Static NAT On Same Interface
Mar 28, 2012Does having the following configuration on an ios device present any possibility that an egress stream PAT'ed to loopback gets source port translated to the statically nat'ed port? [code]
For example, egress private ip address getting pat'ed to the loopback, eventually will have its source port translated to the '7062' in this case. How does the IOS route the return packet vs a new stream hitting the y.y.y.y on the same port?
TP-Link ADSL2+ Wireless :: TD-W8951ND V5 No Longer Have Mac Spoofing Option
Feb 20, 2013Region : Malaysia
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : V5
ISP : Streamyx
TD-W8951ND V5 No longer have Mac Spoofing support.i just bought this modem since my old one is faulty. and i realize that my modem is V5 my previous modem is V4 and there is Mac Spoofing support there.
Cisco WAN :: 892 / Static Ip Address Assigned To The Interface?
Feb 7, 2012configure my cisco 892 router want a static ip address assigned to the interface because and I have no more internet on the router because am working on my network academy for CCENT?
View 28 Replies View RelatedTP-Link Dual-Band Wireless :: WDR4300 Admin Page Ssl Option?
Apr 6, 2013Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I have a question regarding the admin page on the router. Default it seems to accept only http access and I cannot find the option to switch this to ssl over https. Now the admin password goes across the WLAN in clear text which is not secure and not what I want. Is there any way to change the setting so the page is only accessible through https?
Cisco Wireless :: WLC2504 Can't Create Interface On WLC Of Static IP
May 18, 2013I need urgent support on creating SSID as layer 2.We have cisco WLC2504 and 1602i access point. In our network we have in gate for guest.I want to create one ssid and bind with vlan only. We can not creat interface on WLC b/c of static IP.
View 3 Replies View RelatedCisco Firewall :: ASA 5520 - Static Route To Inside Interface
Mar 29, 2011I have inherited an ASA 5520. In doing some auditing of the setup, I have noticed a Static Route that has the inside interface of the ASA as the Gateway IP. I am trying to understand the purpose of this route or why a route would be setup this way.
Example Static Route:
Inside 10.xx.31.0 255.255.255.0 10.xx.xx.10 (10.xx.xx.10 is the inside interface of ASA)
Cisco Firewall :: ASA 6.1 Deny IP Spoof From (global) To (Static NAT) On Outside Interface
Jun 2, 2013I'm receiving an error when trying to access a web server behind from one subinterface to another subinterface on an ASA access the public IP. I'm getting the following:
Global Static NAT Deny IP spoof from (61.X.X.X) to 201.X.X.X on interface Outside
Traffic dies at the firewall stating that the traffic is spoofed from the Global address (61.) to the static (201.) address. Both bound to the outside interface. When I create a static NAT on the firewall there is no problem; however when I'm patting against the firewall to the public IP I get the denies.
Cisco Firewall :: ASA 8.3(2) / PAT Interface Address With Static NAT Port Translation?
Aug 22, 2011I have an 8.3(2) ASA with a single outside IP. Dynamic PAT translates inside addresses to the outside interface address. I would like to use static NAT with port translation to access an inside syslog server. I got an error when I tried using the outside interface address. Can I use both dynamic PAT and Port Translation with the same outside address?This is what I would like to use but I receive an error saying there is an overlap using the outside interface address.(192.168.1.0 is my inside network. 10.10.1.10 is the outside interface IP.)
object network inside-net
subnet 192.168.1.0 255.255.255.0
nat (inside, outside) dynamic interface
object network SYSLOG_SERVER
host 192.168.1.50
nat (inside,outside) static 10.10.1.10 service tcp ssh ssh
Cisco Firewall :: ASA 5510 - Static Route By Interface Or Destination
Sep 21, 2011Is it possible to assign a static route to an interface and not globally on a ASA 5510 ver 8.3.
I have two links between my offices one for Data via a VPN and one for video traffic which is a secure connection with QOS end to end.
All interfaces are on the same security level of 100 except Outside which is 0.
Office 1 Interfaces ASA 5510
VLAN 1 vOffice1Data 10.40.1.0/24
VLAN 3 vOffice1Video 10.40.2.0/24
VLAN 5 vInterOffice 10.40.5.0/24 (QOS connection Between Offices)
[Code]....
At the moment if I try and access data from VLAN 1 to VLAN 4 it gets to the destination ok going through the static route and over the vInterOffice connection but the problem is VLAN 4 returning the traffic. This fails because there is no static route back to VLAN 1. If I create a static route from Office 2 to VLAN 1 then it will route all my data traffic over it as well.
Cisco Switching/Routing :: 3750x - Command Cts Dot1x When Applied To An Up-link Interface
May 7, 2012we're having an issue with the command "cts dot1x" when applied to an uplink interface. It basically kils the connection with this command is applied. Once you remove it, everything is back to normal, the platform is a cisco 3750x.
View 0 Replies View RelatedCisco Switching/Routing :: Core 4506 HA (redundancy) Up-link Interface Failed?
Oct 25, 2012I am trying to troubleshoot my new design as you can find it in the attached file, the setting of the up-link interfaces as below:
View 6 Replies View RelatedCisco Switching / Routing :: 3560 - Accessing Management Interface Using Layer 3 Link
Apr 9, 2012I am setting up a link between buildings that uses wireless links. I'm using Layer 3 routed ports on 2 3560 switches to handle the routing between sites. Normally I would just put these in a /30 and then the switches handle the rest. However, the wireless access points have a web interface for managing them that I want to be able to access, but it's only available on the single NIC that also carries traffic. What would be the best way of making this work? Should I make the link a /29 and give the access points an IP in the same range? If this is the case what do I use for the default gateway for the access points?
I have included a diagram to try to explain the issue clearer. The IP addresses in black are what I would do if this were a standard cable (and indeed this will work, but I wont be able to access the admin interface of the wireless AP) and the red ip addresses are the alternative if I use a /29 (but as I said, I'm not sure what to use for the default gateways).
Cisco Switches :: SG300 / Assign Static Ip Address On Vlan 1 Interface?
Dec 13, 2011I am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
Cisco Firewall :: ASA5580 One Inside Source Address Static Nat To Two Outside Interface
May 10, 2012customer has a server which located in inside interace. and an outside interface connected to ISPA. cu config a static nat map inside server address to ISPA address, one day customer install a new outside interface to ISPB, cu config new static nat ,map same server inside server address to ISPB address. the server will allways be vistited from outside interface and reply, custome want traffic coming from ISPA will return to ISPA, traffic coming from ISPB will return to ISPB. but i found it is difficult implement this on ASA5580. i want use route-map on static nat, but it will not satisfy customer's request.
View 3 Replies View RelatedCisco Firewall :: ASA5580 / One Inside Source Address Static Nat To Two Outside Interface?
Jul 13, 2011i have a problem customer has a server which located in inside interace. and an outside interface connected to ISPA. cu config a static nat map inside server address to ISPA address one day customer install a new outside interface to ISPB, cu config new static nat ,map same server inside server address to ISPB address. the server will allways be vistited from outside interface and reply, custome want traffic coming from ISPA will return to ISPA, traffic coming from ISPB will return to ISPB. but i found it is difficult implement this on ASA5580. i want use route-map on static nat, but it will not satisfy customer's request.
View 6 Replies View RelatedCisco VPN :: 1921 Loop Back Interface / Static IP Address For Client
Nov 17, 2012I have a couple a questions answers on which i cant google for a period. BTW maybe i simly use wrong aproach to choose keywords.
1) Is it possible to assign same ip address to the same client each time it authenticated, preferably without using DHCP? Im definely sure that it possible but cant find corresponded configuration examples (my device is Cisco 1921 with IOS 15.0.1).
2) Is it possible to assign dynamic crypto map to loopback interface (the purpose to make EASY VPN Server accessible through two interfaces - maybe you recommend other approach instead?) - as i move workingcrypto map from phy int to loopback - i cant connect with reason "Phace1 SA policy proposal not accepted"
Cisco Firewall :: ASA5510 Static Routes For Management Interface Not Working
Mar 30, 2011We have several pairs of ASA5510s in failover A/P mode, some running 8.3(2) and others running 8.4(1).
e0/0 = outside
e0/1 = inside
m0/0 = management
The problem we're having is we can't get anything to route out of the management interface unless we put in a static route at least to the subnet level. For example, we want syslog traffic to exit out m0/0 to our syslog server 10.71.211.79. Our 'gateway of last resort' points to the next hop out e0/0, and a second static route with a higher metric and a more distinct network space is for m0/0 as in:
route outside 0.0.0.0 0.0.0.0 192.168.49.129 1route management 10.72.0.0 255.255.0.0 10.72.232.94 10
This doesn't work, and ASDM loggin gives this error: ".....Routing failed to locate next hop for udp from NP Identity Ifc:10.72.232.89/514 to management:10.72.211.79/514"
If I put in a more granular subnet route, or a host route of the syslog server it works, such as:
route management 10.72.211.0 255.255.255.0 10.72.232.94 10 <------------- this works
route management 10.72.211.79 255.255.255.255 10.72.232.94 10 <------------- this works too
Why won't a static route for 10.71.0.0 255.255.0.0 work in this case?
We are going to have numerous hosts access and be sent messages though the management interface of these ASAs, and it would be very burdonsome to have to add a host, or even a subnet, route for every one. I've removed all static routes and tried to rely on EIGRP, but that doesn't work. I also had to put 'passive-interface management' under the EIGRP for this to work.
Here is the pertinant ASA config concerning syslog, routing, and interfaces:
interface Ethernet0/0 nameif outside security-level 0 ip address 192.168.49.140 255.255.255.128 standby 192.168.49.141 !interface Ethernet0/1 nameif inside security-level 100 ip address xxx.xxx.xxx.xxx 255.255.255.128 standby
[Code].....
Cisco Switching/Routing :: Option For WS-C3560X-48T-S
Jul 16, 2012Im trying to find an affordable Cisco switch with similar capabilities and features as the WS-C3560X-48T-S (L2/L3 routing as in IP Base, dual power supply, etc.).
View 2 Replies View RelatedCisco Switching/Routing :: How To Use USB Option On 2960s
Nov 5, 2011just got new hardware and decided to try the newer USB port for IOS upgrades. I could not get the switch to recognize my 2gig flash drive. Do I need a proprietary stick or special format?
I also noticed when I removed it the switches crash dump and rebooted?
Cisco Firewall :: Asa 5520 / Configure Two Static Nat Statements From Inside To Outside And Backup Interface?
Oct 16, 2011I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
object network obj-10.1.1.254
host 10.1.1.254
object network obj-10.1.1.254
nat (inside,outside) static 172.25.10.3
I want to also use nat (inside,backup) static 172.25.10.3
Cisco Switching/Routing :: SG300-52 - CLI Configuration Option
Dec 10, 2012I am trying to configure Cisco SG300-52 switch for the first time and stuck without CLI configuration option. The configuration can be done using GUI, however, configuring using CLI would be more comfortable (as I am used to work with CLI of other Cisco switches)..
I was able to lo gin to switch using SSH, but the CLI appears in MENU format and was not able to find any way to go to CLI mode.
As per some blogs, in SG300 switches CLI mode can be accessed using Ctrl + Z in Menu, which did not work either in my case.
Switch is running with latest firmware version Sx300 Firmware Version 1.2.7.76.
Cisco Switching/Routing :: 4948 No Option For X-modem
Sep 19, 2012I am updating the iOS for a 4948 the bootflash is empty so all i can get into is the rommon. There is no option for x-modem. How can I put the iOS onto this device? [code]
View 2 Replies View RelatedCisco Switching/Routing :: IOS Upgrade Option In 2960S Switch
Dec 11, 2012We have a Cat2960-S Series PoE+ currently running 12.2(55) SE5 ios with SW image C2960S-UNIVERSALK9-M.We want to upgrade the ios to the lastest version but found there are 2 version: 12.2(53) SE2 and 15.0(1) SE.Which is the best & suitable for upgrade?
View 3 Replies View RelatedCisco Switching/Routing :: Adding Dhcp Option 82 On C2960S
Dec 12, 2012I have a very simple setup containing 3 C2960S switches:switch 1: central switch, acting as router between VLAN 1 en VLAN 2switch 2+3: edge switches, connected via 1 link to central switch, both on VLAN 2,Clients connect to switch 2 and 3 using dhcp, switch 1 uses dhcp relay to forward requests from VLAN 2 to the dhcp server on VLAN 1. So far so good.Now I want switch 1 to add option 82 to the dhcp requests so the dhcp server can see whether the request came through switch 2 or switch 3. I tried turning on dhcp option 82 support on switch 1 by doing.
View 2 Replies View RelatedCisco Switching/Routing :: 4507R+E / SSO Not Available As Redundancy Mode Option
Oct 31, 2012Why rpr is the only available redundancy mode option available to me. I'm running a 4507R+E with twin SUP7-E's.
Abbreviated show ver Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.03.01.SG RELEASE SOFTWARE (fc2)Technical Support: [URL]/techsupportCopyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Sun 26-Aug-12 13:45 by prod_rel_team
ROM: 15.0(1r)SG2gp08401 uptime is 6 weeks, 6 days, 4 hours, 59 minutesUptime for this control processor is 6 weeks, 3 days, 2 hours, 21 minutesSystem returned to ROM by RPR SwitchoverSystem image file is "bootflash:/cat4500e-universalk9.SPA.03.03.01.SG.151-1.SG1.bin"Jawa Revision 7, Snowtrooper Revision 0x0.0x1C
[code]....
Cisco Switching/Routing :: RFC 951 Why DHCP Option Has Magic Cookie
Oct 27, 2011In RFC 951, the format of BOOTP packet was legislated, but the vendor information was not legislated in this document, so the authors of this document had described that :"If the 'vend' field is used, it is recommended that a 4 byte 'magic number' be the first item within 'vend'. This lets a server determine what kind of information it is seeing in this field. "
I think it meant that the format of vendor information wasn't fixed in RFC 951, and any vendor can legislate a new format of vendor information by itself. And the value in "magic cookie" can be set by any vendor.But in RFC 2131, the format of DHCP packet was legislated, and the "magic cooke" was fixed to values 99, 130, 83 and 99, I think it meant that the format of option information in DHCP packet was fixed absolutely and any vendor can't legislate a new format by itself.
Since the format of option information in DHCP packet was fixed absolutely, why the network device needs "magic cookie" to identify the mode in which the succeeding data is to be interpreted ? I think the magic cookie is not useful in DHCP packet because the format of option information is fixed. In other words, there is only one format of option information forever.
Cisco Switching/Routing :: N7000 Inter-AS L3VPN Option B
Nov 29, 2012I ran into problem with design that was prepared for Catalyst 6500, but in the meantime infrastructure got upgraded to Nexus. I have two datacenters connected with 1Gbit line (point-point), both ends of this circuit are N7K. There are few segments (like LAN, DMZ, PUBLIC) in separate VRFs in each DC and intention was to carry over these segments between locations using VPNv4 exchange via BGP. Each location have its own AS number and IPv4 BGP session is running between them (for global routing table at the moment). I tried to add VPNv4 to that peering session, but got message it is not supported in NX-OS for eBGP. Tried to find some more info about such limitation, but failed.
Before I start explore other options like Option A (creating subinterfaces per VRF and running separate IPv4 BGP session in each).