I have a issue, my DIR-615 V.E3 has been working good. I have multiple computers connected and all get between 280 and 300Mbps. But then after a few hours the speeds drop to 130Mbps on all computers. After I reset the router the speed returns to 300Mbps. I have it set up to run on N speed only so g devices are not connecting.
View 14 RepliesRegion : Austria
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.4 Build 110429 Rel.36959n
ISP : TPG
I've got a problem with the wireless dropping out randomly. It may take a week before it stops or a couple of hours. I originally thought my microwave oven was swamping the signal when we used it so I relocated the router much further away but this hasn't changed anything. I can still log in to the router from a computer on the wired ports and reboot the router. It also thinks the wireless is working but everything looses connection to it. We have 3 laptops and 4 phones that use the wireless and they all cannot connect when it goes down. This is only a new device - less than 6 months?
My HP Envy 14 has an Intel 6200AGN wireless card. Is it not good enough to achieve 300mbps on my D-Link DIR-655? The firmware is current on the router and the signal is 100% almost every where in my home. Even when I'm a few feet away from the router, the most I'm able to get is 130.Do I need to change a setting on the router or upgrade the wireless card?
View 2 Replies View RelatedRegion : Sweden
Model : TL-WR842ND
Hardware Version : V1
Firmware Version : wr842ndv1_en_3_12_22_up(120424).bin
ISP :
My normal FTP download speed is 1-2 GB/Sec but downloading from the routers USB port only gives 200KB/Sec. How to improve the server speed? Another question: How many users can log in/download at the same time?
Region : Others
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : wr841nv8_en_3_13_27_up_boot(121101)
ISP :
I followed TP-Link's guide to set up a WDS connection between my two brand new WR841ND router. It theoreticaly "works", but the network is extremly slow. Copying a ~100 Mb sized file to another computer on the other side takes more than 10 minutes or more, I don't know exactly, because I shut down the process after 10 min. I pinged the "slave" router with 200 packets, and I realized that every third, fourth and fifth packet has more than 500 ms time. The minimum is 4 ms, the longest was 566 ms.
Router A (Master)
Connects to the internet/ADSL
DHCP enabled
[Code].....
I bought the two router from the same dealer, at the same time. Both have the same firmware. I checked all the chanels, and 5 is the only free one, but the situation is the same on every chanel.
What can couse this very slow transfer speed?
Region : Brazil
Model : TL-WR841ND
Hardware Version : V7
Firmware Version : 3.13.9 (Last)
ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : Romania
Model : TL-WR841N
Hardware Version : Not Clear
Firmware Version : Latest
ISP :
i just bought this router, all good until i had to upload wireless over ftp or samba. It is version 8.2
Firmware Version:
3.13.27 Build 120802 Rel.51024n
Hardware Version:
WR841N v8 00000000
I bought this router for the advertised 300 mbs, my last 150 router was giving me 6/7 mbs over wireless upload on ftp. Tp link router is giving me 800 k.
Download works on wi fi , i got 9,3 mbs from a 150 N adapter.
I tried all security options , even mac filtering . And i am trying to ftp over network , not the internet.
Region : France
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.13 build 120405
ISP :
i discovered a speed issue with cable with my router TL-WR1043ND. i have no more than 11 MB/s from computer to NAS... so like all transfer speed was setup like a 100Mbps adapter. my card on my computer is in auto negotiation. If i set it manually to 1Gbps no link is active between router and computer. i tried it with my laptop and once again the same issue.
Region : Spain
Model : TL-WR1042ND
Hardware Version : v1
Firmware Version : 3.15.1 Build 120618 Rel.41178n
ISP : ONO
I have a wired connection to 12 MBs and is very stable.My problem is that the download speed becomes 12MBs to 2MBs without apparent reason.It is fixes if you restart the router.Here will show you the optimal speed of connection.
[URL]
When this happens again i'll show you the speed.
I recently decided to buy a DIR-655 router to create a wireless network in my home. I hooked it up last night and speeds look fine with my rr standard 10mpbs service. However, I decided to check the wireless status and my macbook, macbook pro, and my desktop computer are only getting at most 130mbps. Is there anything i can do to maximize this and go beyond 130mbps
View 3 Replies View RelatedBRAND NEW DIR 655. Took a bit to get working. Connected at 300mbps beautifully. Then I started to notice I was lagging--I checked my connection speed and it's back down to 130mpbs.I made sure to do WPA2 only, 20/40 range... I don't know what else to do to make it "stick" to the speed I want. It's obviously quite capable of it. If I reboot it it connects at that speed.... it just randomly reverts back to 130.
View 14 Replies View RelatedI have had the DIR-825 since the beginning of the year connected to AT&T DSL Internet 3GB. I just upgraded to their 6GB download speed and didn't see any change in speed and suddenly I couldn't view my SlingBox anymore outside the house. I connected one computer directly to the modem, ran the AT&T speed test and got >5GB download and @700 upload. Wired via 1GB network back to the router, ran the speed test and it dropped to @4GB download and 120 upload.
I called AT&T, they checked everything, and said there was nothing wrong. I then spent almost an hour on the phone with D-Link including getting passed to 3rd level support. I knew something was wrong when the guy told me that since it was only a 1GB router, I shouldn't expect to get faster than 1GB Internet download.
The router is still running the 1.00 firmware and these are the changes they made me try so it's still sitting at these settings:
- Change the WAN from Auto 10/100 to 100 only.
- Change MTU to 1482 in my PPPoE settings
- Change Firewall Settings to turn SPI off. He said the router is still providing a firewall though.
He wanted me to download the 1.01 firmware but I balked and he said it probably wouldn't do any good. It ended with him wanting me to call AT&T back and set the modem to bridge mode. I then need to call them back and set the PPPoE again. This 3rd level support guy was very rude and am hoping to avoid calling them again.
Before I go through the hassle of calling AT&T and trying this bridge mode, or has the Elite 6GB service from AT&T and are having it work correctly.
I think i make big mistake to update E4200 firmware from 1.0.00 to 1.0.04.My ISP speed is 300 then i connect pc.Download Speed: 299.22 mbps (37.4 MB/sec transfer rate)Upload Speed: 267.63 mbps (33.5 MB/sec transfer rate)Then connect E4200 With 1.0.00 firmware speed is ~200.But now firmware is 1.0.04 and speed only 100Download Speed: 103.43 mbps (12.9 MB/sec transfer rate)Upload Speed: 101.88 mbps (12.7 MB/sec transfer rate.
View 9 Replies View RelatedWe recently purchased a Linksys E3200 router, because our old router didn't take advantage of our internet speed. The router works fine, though the internet speeds again isn't as much as expected.
With a wired connection, we only get 80 Mbit/s of our full 120 Mbit/s, according to Speedtest.net. The Cisco Connect built-in speed test is even worse; only 40 Mbit/s. When we directly plug the computer into the modem, we get the full 120 Mbit/s, which indicates that the modem does have the connection speed. The router just doesn't give it to the computers attached.
I don't know about my wireless speed, as my wireless card in the laptop clearly is the bottleneck (it can only connect at 65 Mbit/s). Atheros AR9285 ftw.
We tried different cables, the one included with the router gives the same speed.
Got a Linksys E3200, and a gigabit card, even two, Realtec and Intel, have a connection ggbit. If the power cord plug directly into netcard, all at great, the tracker up to 80 MB per second, shakes on speedtest.net, shows 780 240 + Mbps. When i connect my inet through the router, the speed drops to 12 MB(100 Mbit) and speedtest the same, but in the the web interface in the statistics shows that everything is connected to a gigabit.
Plus, when I ping my ISP's website (ip -t ) and assume [URL] click on the test, the router with 1ms pings are beginning to rise to 30 ms, and when it is directly in netcard, it stable 1ms.... When through the router, torrent shake it just do up to 100ms jumps. I have all the settings , and set up his hands, and a manager, all for nothing. It started five days ago, before that everything was ok. Can a router burn? Rather it gigabit controller?
I have a WAP4410N which I have had for awhile and the performance was flawless at what appeaared to be 300 Mbps. I udated the firmware recently to 2.0.4.2. This is when the problems started. Within 15 feet of the acccess point it would drop the connection and speeds were under 65 Mbps. I factory defaulted the unit and reinstalled the firmware with no changes. I run several other access points of differnt manufacturers and I get fantastic performance on draft N and G. I did check all the laptops for network adapter incosistansies. Have I made a configuation mistake? I only changed the IP address to bring it into the range of other devices. I use a sa520 router and a Trendnet Gigabit switch and a server with MS SBS 2008 which works well with all but the WAP4410N.
View 2 Replies View RelatedI have a Linksys E1000 running on the latest firmware available from the Cisco website. When my main PC (Windows 7 64Bit SP1) which is connected with a ethernet cable is running the wireless speed is great for all my connected devices. (Android/Apple phones, tablets, family PC, etc). But when I shut down my main PC the wireless speed drops to the point where it can take 3-5 mins for google.com to load up. The wireless connection is still showing as strong, just the speed isn't there anymore. If I were to turn my PC back on, everything will load up almost instantly and be back to normal. I've tried reinstalling the router, resetting it all back to default settings and re configuring it but I've had no luck in solving this.
View 2 Replies View RelatedMy ISP provides me internet by pppoe connection.When testing the connection with the router i get 30 mbps.When testing the conection without the router, cable conected to laptop i get 60 mpbs.
View 1 Replies View RelatedI purchased a new router - cisco e1000. Currently, i have 2 laptops wirelessly connected to this router. When i do a broadband speed test, the speed drops down significantly to 8MBPS while if i connect it to the cable modem directly (wired) i.e., without router, i'm getting 15 MBPS download speed. I did a couple of times this speed check and the results are same. I tried changing the advanced settings in the router (which was specified in one of the post in this forum) but no luck. Is it that i need to buy e4200 to match the wired speed of 15 MBPS or what other things I can do to get the same speed of my cable modem (provided by my ISP)?
View 1 Replies View RelatedI'm running a Cisco E4200V2 router with the latest firmware (2.1.4.12284) on an iMac running OS X 10.8. My ISP is providing 15Mbps to my modem, which I've confirmed by connecting directly to it without the router. Once I put the router back in the path, my broadband speed drops to about 6 Mbps. Is this the best I can expect from this router?
View 2 Replies View RelatedI have four E4200's doing the same. I have FiOS 15M download and 5M upload. As soon as QoS is turned on the upload speed drops down to usually 300k and it never exceeds 1M.At the same time any VPN connection gets dropped often.I also configured one E4200v1 as router and the second E4200v1 as Access Point (HDCP off) hardwired to the first one.Any VPN connection gets dropped when changing location. I.e. if VPN was established with the router, the connection gets dropped when in the location where AP is -- and the other way around too. There is no coverage gap between the two locations, to the contrary - they do overlap heavily.On Dec 21, 2011 the level 2 Linksys/Cisco people advised that they will forward the two issues to engineering and that resolution will be within 24-48 hours.
View 5 Replies View RelatedMy problem occurs when i am trying to download something big, mainly the speed of the download raises at a peak and then it drops disconnecting me from the internet for a few seconds. This only happens when my laptop is on a wireless connection and this phenomenon repeats itself untill the download is complete. During the connection crash I am not able to access any site.
My laptop is an Asus G series with Win7 64bit SP1, and I use utorrent for P2P downloads.
Region : Germany
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 8.1
ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
Region : Others
Model : TL-WR841ND
Hardware Version : V7
Firmware Version :
ISP :
my ip address is not static i use no-ip sevice to get dns how to set my tp link for wake on lan
I managed to update ddns in my tp link How do I go from here?
I am currently running a TL-WR851ND Wifi Router whith the latest build 3.13.27 Build 121101 Rel.38183n() published last November 2012. Now is there any new firmware?
View 1 Replies View RelatedRegion : UnitedStates
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : latest
ISP : Time-Warner
Just purchased the WR940N to use as a wireless bridge. I expected to be able to have the router join my wireless network, and provide Ethernet connectivity to 4 devices behind it. But I'm missing something in the configuration. I can get it on the wireless network, and manage it via the wireless network. But devices plugged into the Ethernet cannot get out to the Internet. Basically, I have a 192.168.1.x network, and the router is node 192.168.1.3 on the wireless network. I've turned off the firewall and DHCP on the router. The Ethernet devices behind it get an address from my network, but the router inserts its own address in as the default gateway, and my Ethernet devices do not have a route to my 192.168.1.x network, despite having an address on it.
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP :
I have a WR1043ND
Firmware Version:
3.13.12 Build 120405 Rel.33996n
Hardware Version:
WR1043ND v1 00000000
I tried to connect a WD MyBook Essential 3tb hdd NTFS, but it never recognized it. Of course, I connected it with the external power supply.With a 15gb pendrive FAT32 it works OK.
Region : Russia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :
Region : Russia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : wr1043nv1_ru_3_13_10_up(120614)
ISP : netbynet
Connection to a router on a cable speed of dowstream-50MBit/s, upstream-3Kbit(!) wifi-dowstream-50MBit/s, upstream-3KbitA cable directly in the personal computer to 70 Mbps there and back.Measured speedtest.net, and as [URL] The matter is that even elementary with an investment it is impossible to send mail - I am connected by different devices-2 of the laptop and 2 smartphones - the same. Technical support of provider already talk sense only in a router. Insertions updated, changed - the same( Firewalls are disconnected, any more don't know what to do and where proceeding speed and all digs-is killed. Russian forum TP-Link is idle.
Region : Others
Model : TL-WR843ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I buy TL-WR843ND router to provide a better signal upstairs. Router is in wisp mode with statick ip. Everyting work good. I have routed home network with mikrotik. And everyting was setup with priority on mikrotik for each user separately. With this router every user connercted on it was hidden behind TL-WR843ND. How to disable NAT on TL-WR843ND to use routed network?
Region : Austria
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
unfortunately I've lost my device pin and I've reset my device.can I get the device pin on a other way? on my invoice there is no information about that.
Region : UnitedStates
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : WR1042ND v1 00000000
ISP : comcast
I have a machine called 'survtest' on my lan with a permanent ip addr of 192.168.0.112. I can't ping that host by name from any other machine on the lan, although I can ping the ip address. Not only that but this machine appears in the DHCP client list within the router with its name 'survtest' and correct IP addr.
There is another machine on the lan called 'bsd' that also has a permanent IP addr of 192.168.0.110. It can be pinged by name from any other machine on the lan. However it does not show up in the DHCP client list at all.
Neither of these machines can be pinged by name from within the tplink admin diagnostic screen.
Region : Netherlands
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP :
Is it possible to use a VPN service such as hidemyass on the TL-WR1043ND without installing the DD-WRT firmware?
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]