D-Link DIR-655 :: Can't Connect Any Devices Over 65m Speeds
Jul 11, 2011
i have had a DIR-655 Rev. A router for years now and had no problems connecting my laptop to it well over 150m, the iproducts never got over 65m, i'm OK with that if they just won't but i would like to get there if possible. i went out and picked up a 2nd 655 (rev B) and flashed the bios up to the newest version 2.03NA and went in and mirrored all of the settings from the original router and then replaced the old router with the new one. the old router is not being used at this time though there are plans to use it as an access point later in another part of the house. i have updated the drivers for the wireless N card on my laptop (i can't remember the name of the adapter or the model, i'll provide that when i go home for lunch today). i've tried various settings for security, (i want to use WPA2 only, personal key, AES cipher, channel width 20/40 auto) i've even tried no security and it still won't connect over 65m.
View 14 Replies
ADVERTISEMENT
Jan 5, 2013
Just bought a dir-655, set it up (all though the wizard wasn't working, it kept getting stuck on step 5 of 7) so I just configured everything manually.I'm getting 2.4 MB/s speeds wirelessly.I was expecting much better, my wireless g linksys router did just slightly lower than that. My xbox 360 can't even stream HD without buffering every few mins. It also will just stop, and be unable to see the media for a couple minutes (when doing HD).I have wireless setup as WPA2, and the devices I use wirelessly are N devices. I have the router setup to only use wireless N.
View 14 Replies
View Related
May 2, 2012
On my laptop, I get horrendously low speeds on our modem, but on my iPhone under the same WiFi, I get very fast speeds. On my Laptop, pages render very slowly, YouTube won't load etc. I also can't do online gaming or anything.What's causing this? I've tried the ol' 'turning it off and on again' trick for every thing but it doesn't work. I tried connecting it to the modem and it went slower!
View 11 Replies
View Related
Oct 27, 2011
I have two buildings on my property that I need to network together. One is my home about 3500 Sq. Ft. and the other is a garage about 3000 Sq. Ft. The two buildings are about 250 feet away from each other. Both are fed from the same utility pole that is half way between them. That means both are on the same transformer, but each has its own metered electrical service.Right now I am using 10 Mb. Home Phone Line network adapters. They work OK but data speeds are limited to about 5 Mb. of throughput and the adapters are no longer available. I also have WiFi at both locations but neither one will talk far enough to cover the other building.I also use X10 remote controls in my house. I have tested them from the house to the garage and they do not work at all over that distance
View 7 Replies
View Related
Mar 1, 2013
In my device I am able to browse through & connect to my HOME wifi network ; But after connecting it says 'No Internet Access'.I tried connecting with my SONY Bluray , iphone , ipad , laptops -- everywhere same story.I am able to plug in the ethernet cable directly from modem & able to connect to network.I am not able to open the http://192.168.0.1 -- ( When I am plugged in the modem directly)
Following are my router details
FCCID - KA2DIR601A1
IC : 4216A-IR601
H/W Ver:A1
F.W Ver:1.00 NA
View 12 Replies
View Related
Jan 18, 2013
I'm having a problem where my connection speeds slow down on my iOS devices. I have a EA2700 router. I have PC hard wired into the router, which maintains steady speed test numbers when other devices slow down.i have another pc that connects wirelessly (2.4 only) that maintained speed white the other devices slowEd down. Both my iphone5 and new iPad would slow down. The quick fix wasto turn the wifi on the device off, then the speed would return when reconnected. Also clicking "renew lease" in the iPhone wireless settings seemed to correct the issue.I'm not sure if there is a setting on the iOS devices or the router I can change to stop this.
View 3 Replies
View Related
Apr 5, 2012
We can only connect 2 devices at a time. Someone suggested that it may be a setting with my wireless router.
View 2 Replies
View Related
Feb 3, 2013
I have just switched to a new internet provider (UnityMedia in Germany) and they provided me with a CISCO cable modem (EPC3208G) and a 'wireless N 150 Home Router DIR-600' (hardware Bx and firmware 2.13). I had to ring the service desk to complete set up. I was told to connect the LAN cable (from the modem) into LAN number 1 rather than 'internet' (in the router). I was also told to change the router IP address to 192.168.0.2. Thereafter the connection to the internet was established (they also asked me to make some other changes which I can no longer recall). However after the phone call with the D-link service desk I attempted to connect my other internet enabled devices (kindle, internet radio and smartphone) and apart from one other laptop nothing can connect to the internet.
View 5 Replies
View Related
Mar 21, 2012
I am currently having issues with the dhcp function on my DIR-615. The issue is some of my devices are never able to connect unless I set them up with static ip. Some of my devices are sometimes able to connect using DHCP but sometimes need to be set up with a static IP. In the log it says something along the lines of "sent out offer for IP 192.168.0.XXX" but the devices never receives the IP. The firmware says it is up to date. The hardware version is C1. Some of the devices having issues are PC's some are Macbooks and some are iphone and ipods. I'm not sure if it is related but when I look at who is using WAN some of the pc's who are connected to the internet have an ip address of 0.0.0.0.
View 3 Replies
View Related
Feb 15, 2013
I have a D-Link DIR-652 router, and I can see that it is broadcasting but I cannot connect through my laptop, tablet, or phone. Sometimes it will let me connect but other times it says it is unable to. I can connect when I plug into the router through a cable. I'm doing that now, and I did an ipconfig/all in case to see that:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Kyle-PC
Primary Dns Suffix . . . . . . . :
[Code].....
View 10 Replies
View Related
May 12, 2013
For some reason, handheld devices cannot connect to our wireless dlink router. However, our HP laptop has no issue with connecting. Regardless of the make and model, no one else can connect at our home.
View 5 Replies
View Related
Nov 1, 2012
i've just a D-Link DIR-600 router last month and i successfully installed it and its working great. Until 2 to days ago, my brother told me that he can't conlnect to the wi-fi. I said that its working just fine and told him to just reset his phone. And then, my sister also told me that she can't connect too. I checked their devices like iPhone 4S and iTouch and it says "Unable to join the network....... Also phones of my friends can't connect also. It was just working fine. I haven't changed anything on the router's configuration. I already reset the router, unplug then plug it and its still not working. The router is connected to my laptop and I can still browse the internet. Its the wireless connection that is not.
View 5 Replies
View Related
Jul 31, 2012
DIR-615 REv E, Originally had a Windows vista, windows 7, sony bravia tv (hardwired), sony blue ray player, 2 blackberry torch, an ipod, and whoever else happened to be there connected. After a router push button reset 7 reconfigure, only the windows vista and a samsung tablet will connect. The windows 7 computer sees the router but cannot see the internet. It does connect if hardwired thru the router.
View 1 Replies
View Related
Mar 1, 2013
I have the firmware 2.10NA. In my home we have about 4 laptops and 4 smartphones connecting to this router wirelessly and 3 of the laptops often lose connection for hours. We have tried unplugging the router and plugging it in again and factory reset and also resetting it through the IP address but the connection doesnt come back. Recently it has gone out for about 3 hours now. Also the wireless LED icon on the router constantly blinks is this normal? On the laptops where theres no connection it says limited connectivity. Is it possible that there is too many devices connected to the router or something. or could this be a problem with the laptops and not the router?
View 6 Replies
View Related
Nov 29, 2012
Region : UnitedStates
Model : TD-W8961ND
Hardware Version : V2
Firmware Version :
ISP : ATT
I want to add more users to my home network and I couldn't, at this moment I only can connect 8 devices (12 devices at least) when I try to connect the next one its impossible, but if I take off one of the connected devices then the router allows to connect the new one.How can I connect more than 8 devices to my router ? (wireless)Also, is there any limits with Wireless MAC Address Filter ? because I can't add more than 8 MAC addresses in my old router I could do that.
View 4 Replies
View Related
Feb 11, 2011
I am currently using a DIR-655 for the home wireless network.DSL into a 2-Wire home portal (not wireless) and ethernet into the DIR-655.I need to connect a number of wired devices in a couple of different rooms. Some streaming HDTV content to other devices in other rooms. I'm thinking of the following:
-DIR-655 routing between the DSL subnet to the internet, the 2.4GHz wireless and a couple of wired devices.
-DAP-1522 routing between the 2.4GHz wireless, 5GHz wireless, and a few wired devices.
-DAP-1522 bridging between the 5GHz wireless and a few wired devices.
All devices will/may need internet access.HDTV content would be between wired devices and only over the 5GHz wireless (no HDTV to/from internet).Is the DAP-1522 the right device(s) for this?
View 2 Replies
View Related
Oct 11, 2012
All of a sudden my laptop, android phone and blu ray player (all wireless devices) can't communicate with my wired devices (marantz receiver and samsung tv). Everything still connects to the internet independently but i can't for instance play music from my wireless laptop to my wired marantz receiver. I had no trouble with this last week and didn't change anything (that I'm aware of) I did get Verizon to switch out my router but it didn't solve anything. My wife's computer also cannot connect to wired devices. Lastly, if I connect my laptop with via ethernet cable it sees wired devices fine. I tried shutting off windows firewall but didn't work. I have no other firewall/virus software installed. I can ping to all devices (wired and wireless) from my laptop.
View 1 Replies
View Related
May 19, 2013
My Belkin F7D4301 Router has the fastest wireless speed of maybe 2MBps but wired with a cat5e cable to my asus laptop of almost 7MBps. I have a one smart TV, one blue ray, one roku, and a nexus 7 using the 2.4 channel.
My Wireless 2.4 settings are channel 11, Extension channel 7, Wireless mode N (have tried with just g and b, g, and n modes), Bandwidth 20/40, Protected mode on, QOS off.
I've talked to Belkin tech support, they are the ones who had me set up my 2.4 channel this way but my wireless speeds stay just under 2MBps, they just want to keep sending me the same model Router because they think each of the new ones they send me is defective.
Am I doing something wrong or is 2MBps the best wireless speed I'm going to get?
View 1 Replies
View Related
Jan 12, 2010
I'm paying to get Download Speeds of 25Mbps from my cable provider.
If I plug my computer directly into my cable modem, I get 24.98 Mbps every time.
Using the same speed test, if I go through the DIR-655 I get rates from 2.92 to 10 Mbps.
I'm on Firmware 1.32NA. I'm ready to go out and buy a different brand Router.
View 8 Replies
View Related
Feb 27, 2012
Okay i just got the DIR-615 N Router and at first i was getting 40 ping on speedtest.net but now I'm getting 360 ping which is really frustrating since i upgraded because my old one was having troubles and also when i get to the check connection in the setup i am getting Your new router does not appear to be connected properly.
View 3 Replies
View Related
May 17, 2011
I'm surprised to see speeds around 11MB on a gigabit LAN and the NAS is also gigabit. I've been reading that when people take the DLink router out of the loop that there speeds get upwards around 48Mb or so. Or if they add in a non DLink switch put the equipment on that leg with the switch.
Are there some tweaks in the 825 that could work for the LAN speed for this NAS? Seems odd to have to buy a new router or add in a switch to do what this should be doing already. This is going to be an issue for streaming movies and especially HD via WiFi across the LAN.
I would also like to do my data backups to the NAS but when they hit around 60Gb it would take a long time to do a backup.
View 14 Replies
View Related
Aug 11, 2012
How can I optimize my router to get maximum transfer speeds? I average 72 Mbps.Notebook-Speedtest.net 31.58Mbs down/3.08 up. I'm just confused about transfer speeds not being 300 Mbps. Can or should I correct this? When I purchased router it said the transfer speeds would be 300Mbps.
PC1: Connected directly through 1 gigabit ethernet LAN.I'm using a MSI GT640 notebook with a onboard NIC, Ralink Techology, Corp. 802.11bgn 1T1R mini Card wireless network adapter. Driver date: 7/6/2010, Driver Version: 3.1.8.1. ( WLAN RF module Ralink RT390, MSI MS 6891).
[code]....
View 3 Replies
View Related
May 26, 2012
I've been having issues with my DIR-655 - the speeds are super slow. In the past, I've been able to restart the modem, and my speeds would be acceptable, but now a restart doesn't change the speeds I'm getting from speed test.net. I know it has to do with the router, because when I directly connect to the modem, my speeds are great.
-Speeds WITH router:
-Speeds WITHOUT router:
And like I said, in the past I could restart the router, to get similar speeds to just my modem, but it doesn't work that way anymore.
View 1 Replies
View Related
May 18, 2011
I've got the DAP-1522 connected in AP mode. Multiple N speed laptops but they're limiting out to G speeds (54 mbps). Firmware 1.31. Current config is
Wireless Mode : Access Point
802.11 Band : 2.4GHz
802.11 Mode : n and g
[Code].....
Connecting with brand new windows 7 laptops. N Capable. Some G laptops on the network as well.
View 2 Replies
View Related
Apr 13, 2011
I have a DSL connection with AT&T. It is rated at 6Mbps / 768Kbps, but it closer to 4Mbps / 600Kbps. I have a speed stream 5360 connected to the DIR655. Devices on my network are primarily wireless and include; several laptops, a desktop (which is wireless n), a couple phones / Ipods and a Wii that I watch Netflix on.
I do a lot of Photography and a handful of video work, and backup / share everything online. When I am uploading photos, even with "conserve bandwidth" turned on in the uploading application, browsing sites is very slow, but reasonably functional. If I try to upload a video to YouTube, I can barely manage to do anything else the entire time it is uploading. I've tried to plan and run all my uploads overnight, but then Netflix is unusable when I want to watch it at night.
I've tried several different things, first off, with getting the Wii to function for Netflix, I turned on the QOS engine, for the IP that is assigned to it, and set it to priority 1 for all ports. I also have a entry in the QOS engine for SSH on port 23 with a priority of 10 because of how laggy my SSH sessions are. I do not have any other entries in the QOS engine, is that a problem? Should there be entries that cover other services and assign them a lower priority?
I have enable traffic shaping and Automatic uplink speed turned on. It measured the uplink speed at 695kbps, which is pretty accurate. I have Automatic Classification off, and Dynamic Fragmentation on. WISH is enabled also. I'm set to mixed n, g, and b, I'm not positive, but I do think my older laptops only use wireless b.
Even more importantly than the Netflix would be to allow me to use the Internet in a functional manner while I am uploading, that would solve a lot of problems. It seems that the uploads just hog every last bit of upload bandwidth and don't want to make room for even the small requests that one needs to send to view a web page.
View 2 Replies
View Related
Aug 17, 2012
We recently bought a home and just moved in. That being the case, we got a new ISP (Cincinnati Bell DSL). The service is advertised as "Up to 5Mbps."
My current equipment:
PC:
OS Name Microsoft Windows 7 Home Premium
Version 6.1.7600 Build 7600
Other OS Description Not Available
[Code].....
So what can I do to achieve faster speeds? Am I limited by the hardware I have? My Dell is roughly 6 years old. Am I limited by Cincinnati Bell? Is it the location of the wireless router? Are there settings I can adjust to create a faster connection?
View 6 Replies
View Related
Dec 14, 2011
I had my Dir-655 router for over a year & this is is a first.My firmware is 1.21 & I only use my router for gaming when I'm not on my PC for home use. I have only one PC in the house that is not shared, I have also not downloaded any virus or maleware.So the past month I decided to buy a wired ethernet cord to connect to my gaming systems rather than using the wireless option to get an extra bit of speed. That has been working fine up till yesterday when all of a sudden my download speeds dropped from around 20Mb down to barely 1Mb down (I can't even get the speed test site to fully load anymore). The upload & ping remains unchanged though. Only my Download speed is being affected. This is both when I'm on the PC & when I'm online gaming.
I unplugged my D-Link router & plugged my modem directly to my PC & I got back the 20+Mb speed, so the modem or cable company are not at fault (I even called them to see if there were any problems on there end).
-I tried turning off my Firewall on my PC.
-Resetting & rebooting both my modem/router/PC.
-using different DNS numbers.
-using /flushdns.
-using /Iprenew.
-Messing around with my router configurations such as:
turning off QoS Engine.
turning off wireless.
turned of MAC filtering.
unchecked "Add DHCP Reservation".
unchecked SIP.
None of it worked. I'm still browsing at around 56k dial up speed for the past day+!I read up on the internet for similar problems, but the only solutions I saw was turning off the firewall on the PC, but that hasn't worked at all.
View 4 Replies
View Related
Mar 24, 2011
Router:Dir-655 (Hardware Ver B1;Firmware Ver 2.01Na)
Modem: Motrola SB6120
Cables: Cat 6
Machines: 1. XP SP3 w/d-link DGE-530T desktop; 2. XP Pro SP3 w/dlink DGE-530T desktop; 3. Win7 64 (Latest Drivers)
Problem is that the XP machines can download 25Mbsp on speedtest.net but the Win 7 only manages 5Mbps through dir-655 -- ALL WIRED CONNECTS!. Connect Win 7 directly to modem and d/l is 30Mbps 2 hour Netflex test of wireless indicates good performance. D-Link support had me going in circles for a while until I finally suggested that a firmware update was in order. They assured me that this had been id'd as a problem and that latest firmwire would certainly solve it. It did not.
View 14 Replies
View Related
Feb 5, 2012
I recently bought and installed a DIR-615 for my home network, and downloaded the Yahoo Widget.
Widget recognizes and display all the config information (LAN, WAN, WiFi) fine, but it does no display any of the speeds (which was the whole idea).
View 2 Replies
View Related
Mar 1, 2010
I'm currently subscribed to Comcast's 22/5 Internet service. Internet upload speeds on both wired and wireless are about the same at ~ 5 Mbps. Wireless download speeds range from .5-3 Mbps. Wired or Wireless, I receive LAN speeds of ~32 Mbps or 3-4 MB/s. The noticeable issue is wireless internet download speed. I have tried every configuration possible with my router, updated drivers on devices, firmware and tested everything I could on all PCs, and even used the XBOX 360's media extender network tuning feature as a tool in my investigation to find this bottleneck. All reports point to internet download speed. Again, general LAN and internet upload speeds relatively meet expectations. The wired download speeds are slow at times, but consistently meet expectations.
My current Setup:
Wifi
A4 1.33NA
WPA2 Only - Personal
802.11 Mode : 802.11n only
Channel Width : 40MHz
Channel : 1
[code].....
View 6 Replies
View Related
Oct 26, 2012
I have tried 2 DIR-655 routers now, revision B1, firmware versions 2.04, 2.07, 2.08beta and a number of laptops and wireless mini pci-e nics and I simply CAN'T get faster than about 10 megabytes/sec transfer speed from a wireless laptop to a wired gigabit desktop.
Is this just simply a limitation of these routers? Can they simply not transfer data at decent speeds? I've seen real world transfer speeds near 12 megabytes/sec on a DIR-615 and I assumed the limiting factor there was the 100megabit wired connection.
I've spoken to a dozen different D-Link phone support workers
View 14 Replies
View Related
Jan 9, 2013
I have a DIR-655 that I have been using for a while (b1 revision). and suddenly I noticed my wifi speed fluctuates constantly. My lenovo Y580 sees speed drop to 130 immediately and then it can slowly progress to 1 Mbps until the hardware is all rebooted. Same happens to my Nexus 7, Dell XPS M1530 and to my roku. I have updated to 2.07 (since 2.10 is advised to avoid). And I have attempted changing channels or factory refresh.What Firmware version is currently loaded? 2.07What region are you located?
What ISP Service do you have? Cable or DSL? Cable (link speed independent of internet speed)What ISP Modem do you have? Stand Alone or built in router? Separate Motorola ((link speed independent of modem)What ISP Modem make and model do you have? Does not matter, router issue.If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. Not bridged
Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic. Independent of issue, not a factor
Turn off all devices accept for one wired PC while testing. Wired works perfect.Check cable between Modem and Router, swap out to be sure. Cat6 is recommended. Wireless issue.
View 6 Replies
View Related
Nov 16, 2012
wr2543ND / very slow shared storage transfer speeds?
View 4 Replies
View Related
