D-Link DIR-655 :: Email Server Inaccessible Via WAN?
Jun 3, 2012
Up to this point, all the computers on the network accessed the e-mail server via the Windows name of the PC running the e-mail server. However, one of the PCs will need to access e-mail from the WAN soon as opposed to the LAN, so I switched the server name in Thunderbird (e-mail client) to the actually fully qualified domain name of the server (registered at NO-IP, which redirects to the e-mail server at home).
The problem I am running into is that all the requests sent for IMAP or SMTP are being blocked by the router. That's even though I added port forwarding rules for them. The logs show messages similar to the following:
"Blocked incoming TCP connection request from 22.214.171.124:51291 to 126.96.36.199:143"
It doesn't make a difference if I change the endpoint filtering to "Endpoint Independent" either. Any thoughts of what else I can try? DMZ is not an option.
I have a question about NAT behavior on FWSM 4.0. The problem is email server (Company A) cannot connect to email gateway (Company B) on the outside network and it randomly happen. I got this error from server guy "Detail: xlate has blocked the connection between A’s mail gateway and B’s mail gateway". It work fine again after clear xlate on firewall. [code]
1. How FWSM create xlate table like that? I mean it look like NAT0 for 188.8.131.52 but it doesn't has any nat rule for 184.108.40.206 on firewall.
2. What does it mean "connections 24" at the first of line? In the normal time, I only see the connections is 0 like the second line of xlate
3. After clear xlate global 220.127.116.11, the first line of xlate table is gone then email server can connect each other. Does is a bug on FWSM? or This is a normal NAT behavior of FWSM.
I'm hosting my email on an Exchange Server 2003 box and have my laptop (Vista Ultimate 32 bit) setup to connect to the exchange server for my email. This works fine through a LinkSys RV042 in one location and a LinkSys WRT54GC in another, but fails through the DIR-615 B2 (2.24 firmware) at home. I'm guessing it's blocking something needed for the MAPI connection.
I need to access my employer's website to make changes from home. At work, I use a Mac and can use the built-in tools in Finder to quickly type in the ftp and log in. However, if I try to go in through Filezilla on a PC, the server never connects. I have tried using SFTP and CyberDuck as a web dev with no luck.
I've got the DIR-825 2.02. I had an issue where if you did change the IP adress default 192.168.0.xxx to something like 192.168.yyy.xxx, the configuration page was becoming inaccessible. It was super slow, was displaying the wrong pages with missing images and wrong page formating. I had to reset the router to default and then it was working fine.That seems to have been fixed since 2.05. Now you can change the default ip adress to anything you want and the configuration or setup still work fine.When I am on LAN, the setup page are displayed almost instantly. By remote, it's super slow.
Basically, I have a LAMP server for a small landing page for myself.It was all working fine until I got my new router.Now, I can only access my sites on a LAN.All the ports (3306, 80, 22) are opened and multiple port checkers online says so.I followed some of the basic steps mentioned in this forum such as firewall settings such as:
"Port and Address Restriced" disabled QoS Enabled Multicast Stream enabled DNS Relay set DHCP range to avoid any IP conflicts
Ive even temporarily removed all firewalls completely to make sure that is not the problem.
Region : UnitedKingdom Model : TL-WR841N Hardware Version : V7 Firmware Version : 3.13.9 Build 120201 Rel.54965n ISP : Linpop
I have had my WR841N for about a year, supplied to me by my WISP. I like the router in terms of facilities but it seems to have one really annoying problem.
The router becomes inaccessible via the webpage after a random period of several days. I have at times associated the issue with occasional loss of radio broadband service but it is not always so. To try and further localise the problem I set the router up to send emails of the log to me every two hours from 17/04/2013 but today for the second time the emails stopped arriving after the 02:29 message and the router is inaccessible again. The router previously locked up with loss of broadband service on 26/04/2013 sometime after emailing a log at 02:41 on that day but had been running without issue from a cold restart at 12:25 as soon as I noticed loss of service. Today I have not lost broadband service and so even though I am no longer receiving an emailed log or able to access the router via its webpage I am leaving well alone for the present. Some months ago when I originally noticed the web access issue I downloaded and installed the latest firmware TL-WR841N-v7-120201 and I note that there have been no further firmware releases for the v7 model.
My broadband service is delivered via radio link from a local transmitter mast and is reliable with typical download speed of 20-30Mbps and 30-40Mbps upload, seldom if ever affected by weather so I now feel the problem is inherent in the router rather then being the result of some issue affecting broadband service which has been solid since 26/04/2013
Without the log I have no way of knowing what was happening when the router became inaccessible but I attach the last 24 hours of received log below.
May 5 00:59:42 DHCP NOTICE DHCPC Send REQUEST to server d91650b2 with request ip c3cecc76 May 5 02:29:44 OTHER INFO Mail successfully.
I've recently purchased a domain name from GoDaddy, and I'm having trouble setting up my server, which is running Windows Server 2003, to run email using the domain name. Before purchasing, I was using a free domain from DynDNS and it worked using it as an domain address. I'm wondering if maybe I have to set up the DNS on GoDaddy to foward the email protocol to my server.
Do I create an SMTP Network Object and send TCP traffic throught NAT?
Or do I go to the ASDM's Configuration/Firewall, choose Public Servers, and choose Private Interface=inside, Public Interface=outside, set the private/public IPs, and choose SMTP as the service? This seems much simpler, but is it the correct way to do it?
I am using ASDM 6.4(5) and would like to use that versus the CLI.
One of my customers uses Comcast email and all of a sudden couldn't send messages the other day, telling me it was giving her an error. She said that she reset her router, and the email started working again.When I finally got over there to check it out, the email had started experiencing problems again. The error she was having was Error 550: Message Rejected (when trying to send email). There didn't appear to be any issues with her internet connection, and she wasn't having issues connecting to the email server, it was simply rejecting her messages.
I told her that she would have to contact Comcast, as there was really nothing I could do to fix their email server returning an error. She wasn't too happy, and remained convinced that her router had something to do with it. It's a Netgear WNDR3700 or WNDR3800 that I setup for her last year, it's a fine router.Has anyone ever had a Comcast email server randomly start rejecting messages? I noticed that her outgoing email was set to use port 587 which seems like a nonstandard port and also no authentication, but I have no idea what the Comcast email settings are supposed to be.
1. my email going out is working along with internal, but inbound email is not working. My barracuda email filter is 192.168.1.107 and my exchange 2007 is 192.168.1.222 along with this OWA does not work.
2. Terminal Services does not work when I try from the home pc in I get server not available or disconnected
Below is my congig
ASA Version 8.3(1)!hostname wsigatewaydomain-name wsystems.comenable password yVSkMxWRc/S396FB encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0 nameif outside security-level 0 ip address 64.XXX.XXX.XXX 255.XXX.XXX.XXXinterface Ethernet0/1 nameif inside security-level 100 ip address 192.168.1.1 255.255.0.0!interface Ethernet0/2 shutdown no nameif no security-level no ip address!interface Ethernet0/3 [Code]....
Just installed a RV042 with dual wan connections. Would like to make the WAN 2 (new cable modem as well) the primary connection over WAN1 (DSL), however whenever I switch from WAN1 to WAN2 in Smark Link set up, our email server will not send mail out, even though nothing is blocking the connection.
I have recently purchased six quantities of DIR-655 for my home use. When I registered them these six product, at the end of each registration, I got the message that I will get an email confirming the registration.I didn't get any email. I have checked my email span box and filter too.
I run a mailserver behind my router. I have port 25 forwarded as a virtual server. Not always, but often enough to be annoying, the connections show as being from the WAN port on the router instead of from the real origin. Is there any way to stop the DIR-655 from doing this?
I can't get the email to work from the router. It worked flawlessly for weeks then stopped working. I verified that the outgoing settings are still valid and that my antivirus is not blocking the email.
I have been trying to setup my DIR-655 A4 (Firmware 1.34NA) router to send me email notifications on new firmwares, when the log is full and every Saturday. So I have a schedule already created for sending the emails on Saturday and I also have the option to send notification of new firmware checked. Now I have settings, similar to the following, under email settings.
Any way to get the DIR-655 to e-mail logs? I have all the e-mail settings set properly, but when I request the logs to be e-mailed, I never get anything. Its not in a spam folder either.I do have the DIR-655 behind a 2wire router/DSL modem. I don't know if this is the problem, but I can send and receive e-mails from my computer which is connected to the DIR-655, so I don't think that is the problem.
setting up the email notifications. I need the log emailed to me during a certain time of the day and it wont email anything. Even when I am in the log and push the email now, it does nothing. I've tried setting it up through hotmail, lmsn live, and gmail. None of them work. What am I doing wrong or what do I need to do?
I've just successfully set up my network camera and as I was running through the advanced settings, what it wants from me when it comes to setting up images being sent to my e-mail. I've looked up some old threads to get a clue and thus far nothing works. Testing my entries results in "Invalid e-mail setting" 10 out of 10 times.
The setting format I'm trying to use is as follows:
DIR-655(A3) 1.33NAb02_HNAP_beta I used to be able to send notifications on log full etc... When my ISP was still allowing outbound email w/opt out of block on port 25. This worked on my old DI-524, and used to work on my DIR-655.In an effort to clamp down on spam my ISP formerly SBC now AT&T began requiring SSL. Secure Authentication is not required. With the ever increasing concern for controlling spam DLink really needs to get in gear and provide the support customers need and back the efforts of ISP's to control spam. Otherwise it's wasted code occupying space. On that note if space is a concern, need space for the code ~ throw SecureSpot out !
On the Outgoing Server (SMTP) Settings window click Edit and verify:
# Server Name - displays smtp.att.yahoo.com. # Port - displays 465.
Note: When updating the secure server settings, check SSL checkbox first to update the port setting.
* Under Outgoing mail (SMTP), the box next to server requires a secure connection (SSL) is checked. This works flawlessly with Thunderbird and other mail clients therefore it is clearly a shortcoming of the firmware on the DIR-655 i.e. no SSL? This is totally inadequate.
As the subject says... Sending logs using "On schedule" option doesn't work. I have my own personal email server I used to test this. When the router time reaches the defined "Start time" nothing happens. I tried both time formats (12h, 24h). The router does NOT initialize the process of sending the email. I see that in my server mail logs. If sent manually from Status -> Logs -> Email now, it works. If sent using "On Log Full" option, also works.
Router does not accept any email address that start with a number. For example, if you want to set email address email@example.com in the from field you will receive the following error: The given FROM address (firstname.lastname@example.org) is invalid. Same error if you use it in the to field.HW ver. A4 running firmware 1.35NA.
Region : Canada Model : TL-WR1042ND Hardware Version : V1 Firmware Version : 3.12.22 Build 120424 Rel.39632n
I have a WR842ND with firmware 3.12.22 Build 120424 Rel.39632n. I can't seem to get the mail log emailed out. I've tried hotmail, gmail and ISP email ids. I know these will work as I've done it with my NAS and other routers. When I'm in the System Tools/System Logs/Mail Settings I have authentication enabled and I know I've put in the proper information including mail server outgoing mail names EG. smtp.live.com for hotmail.
I don't see any place to identify a non standard port IE. not port 25, to use. So when I try to send I get the Userid or password is wrong message. Do I have to configure something else.
Region : Argentina Model : TL-MR3220 Hardware Version : V1 Firmware Version : ISP :
Region : Sweden Model : TL-MR3420 Hardware Version : V1 Firmware Version : 3.12.21 Build 120523 Rel.37880n ISP : www.ownit.se
I recently got a new email provider with a webmail. But I can not access the email from my home network. I have tried both my computers so I suspect that it can have something to do with my router. I have also set up the new email account in Outlook and in other networks it works fine, also the webaccess works fine in other networks. It seems that the problem is only related to my home network.i have talked to my ISP provider and they say that all is opened in there network. i have tried to clone the MAC address and that did not solve my problem. I also read the one could change the MTU size from default 1500 to 1440, that did not work either.
When a friend sends me an email with a link to click on when I click on ther link a blank page pops up with the words "404 not found". Why does this happen and is it a big problem. This problem just started to happen a few weeks ago. I never had a problem whenever a friend sent me an email with a link to click on.
Is there any way to change the subject line of the email alerts that are sent? Right now mine are coming with the MAC address, date and time. I would like to remove the MAC address and date and time so that I can sort them into one folder when I sort my email by subject.
I recently set up two cameras. I had set up one for motion detection and email to a gmail account. It seemed to work fine, but then for some reason the motion detection tab didn't show the room like it did before. It doesn't show any picture or anything like it did before, so I couldn't choose the squares to choose the detection area. This is through mydlink account->camera info->advanced settings, and logging in to the camera remotely.So I switched to the other camera, and got it working as of last week. But now, the motion detection doesn't work anymore? It appears to be related to the username/password for the email account. I can no longer send test emails, it says invalid username/password, though the exact same values worked last week, and I didn't change anything. I tried resetting it, then setting it again, but no luck.
the 942L is up and running but I ain't getting no email snapshots nor video clips.I think the menu for setting up the "Video Clip" and "Snapshot" is severely lacking info for users like myself; what to type in the smtp field, the sender or recipient email fields, and especially not username and password. Do I put my email username and password there, or my MyDlink login email and password?
On my new 942l, after 5 days of usage and tinkering with various settings, I cannot get the camera to obey the trigger=motion when configured to send snapshots over email. It does work when configured to send snapshots over email with trigger=always.Interesting enough the trigger=motion works just fine to upload snapshots to FTP. Yes, it uploads the pictures correcty on FTP detecting correctly movements, but it would not send those over email. To me it looks like a bug in the firmware that I have now a 100% repro.Are there any logs you want me to send to you for debugging?And : Is there a known workaround I can apply (reboot, resetup etc)?
Detailed description of the problem:I have setup the camera to upload snapshots to FTP AND send them over email for trigger=motion.This is what works : the snapshots are nicely uploaded on FTP , but not sent over email.Interesting : if I set trigger=always, snapshots will both be uploaded to FTP and sent over email. The moment I switch back to trigger=motion they go only to FTP and not over email.Even more interesting : the video clips work correctly with either email or FTP for trigger=motion.
What could cause this?The email (account, port, password) and FTP settings are definitely not a problem since I see pictures/videos in email or FTP with trigger=always.The motion settings are not a problem either since snapshots upload correctly on FTP when movements are detected.What it apears to be is the software is not reading or obeying correctly a certain combination of settings.I'm wondering if it has to do with the fact that for video clips the "email" and "ftp" are exclusive, but for snapshots they are allowed simultaneously. And somehow the logics get mixed up causing certain combinations of settings to now act out?
What else I tried?I tried many reboots, unplug followed by plug back in and so on.I tried saving and restoring the settings to/from a file hoping that will "reset" something.And I tried many combinations of settings, including changing the order I set and unset hoping a different code path that works will be hit.I did not try a restore to factory defaults since I installed the camera in a hard to reach place and if I restore to factory defaults i need to take it down connect it to a cable in order to redo the wifi settings.
Motion detection is setup - and I can see in the log and on the Live Video "Motion Trigger Indicator" that this part is working. I can also send test-emails, so the smtp is set up correct. In the Event Setup I have a valid server and a motion triggered event with the status ON. But no emails are sent . In the log there is also no indication of the server trying. Am I missing something - or is this not working for anybody?
And - there is no firmware beyond 1.0 for this model as far as I can see.
P.S. I am using a Gmail account for smtp, port 587 and using startTLS to send with,