D-Link DIR-655 :: Restored Configuration File Has Been Uploaded In Failure

Mar 20, 2012

I'm only able to restore my settings from a backup taken in July 2011.  Any backups that I take, say today for example, won't restore.  Any attempts to restore them is returned with "The restored configuration file has been uploaded in failure."  I haven't changed my router.  The firmware remains the same. I'm using Firefox, though I believe I've always used Firefox to interface with the router. 

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: E2500 - File Larger Than 1kb Is Not Uploaded

Apr 20, 2012

I just bought a Cisco-Linksys router E2500. Installation went fine, Internet is ok...
 
Just a small issue when I'm trying to upload a file to a distant FTP server. Any file < 1KB is fine but when the file is larger than 1KB, I can't upload it anymore (it just doesn't complete the upload).
 
I tried passive/active mode for my FTP connection.
I tried port forwarding.
Now I deactivated the router firewall and I put myself in the DMZ.
I also tried to upgrade the router's firmware to the latest official version, and to the DD-WRIT latest version.
 
But still I can't upload files larger than 1KB. With my previous router, it was working pretty fine.
 
The ultimate test was to connect myself on a VPN server and try to upload the file to the FTP through the VPN server. And it worked!!!
 
But I don't want to be always connected to a VPN when I want to transfer files to my FTP server...

View 1 Replies View Related

Linksys Wireless Router :: EA4500 Cannot Connect To Internet - Restored To Factory Configuration

Jul 9, 2012

I've bought the EA4500 and configured it to connect to internet. it works fine.however, one day after it, it can't connect to the internet anymore.I go to the router setup page and try to manually connect it to the internet, but it keeps "connecting." I then restore to its factory configuration, then do the configuration again and it can successfully connect to the internet.however, one day after it, again, it can't connect to the internet anymore.

View 2 Replies View Related

D-Link DIR-655 :: What Is The Path Or File Name For Saved Configuration

Mar 15, 2011

What is the name or path for the file stored on your hard drive for the configuration settings?

View 7 Replies View Related

D-Link DIR-825 :: Possible To Load Configuration From Saved File

Nov 10, 2011

Is it possible to load the configuration from a saved configuration file from a DIR-625 to a DIR-825?  If so, what steps are required?

View 1 Replies View Related

D-Link DIR-655 :: Router Configuration File Format Difference Between Rev A And Rev B

Mar 31, 2011

I've owned the Rev A DIR-655 for years and have loved it, but recently it started acting up. I have a complicated setup saved as a gateway settings file (.gws).  I decided to purchase a new DIR-655 for the ease of importing my settings without having to manually setup again, however, much to my dismay, the new file format for the configuration settings on the Rev B is not .gws but rather .bin.  The .gws file will not import. I tried changing the file extension to .bin with hopes it might import but no luck. I also found the utility which decrypts the .gws file into .xml and used those values to manually re-enter the settings into the Rev B router, but my port forwarding is not working the same.  I was wondering if there is any utility to convert the .gws file to the .bin file in order to import into the Rev B router, or if not, can I still purchase the Rev A model somewhere. The online shops I've checked do not list the hardware version. 

View 7 Replies View Related

Cisco :: LMS 4 Configuration Collection Failure

Nov 20, 2011

I'm having an issue with LMS 4  where it's failing to collection configuration from devices.
 
The following is the status of your Scheduled Config collection job:
 
Job ID         : 1045
Status         : Job Failed(111)
Description    : System config collection job

[Code]....

I researched through this forum and found a thread where the ConfigMgmtServer server wouldn't run. Looking at the processes it says that this service is running normally.

View 1 Replies View Related

Track What Is Being Uploaded From Computer?

Mar 19, 2011

My upload is very high but I dont use any P2P programs. Can I track what is being uploaded?

View 2 Replies View Related

Cisco Application :: ACE 4710 Getting Configuration Download Failure

Jan 22, 2013

I have Ace 4710 version A4.1.1 and I am experiencing interesting problem with GUI and SSH reachability. I am unable to connect to management vlan3000. Interesting is that I can ping from ACE to network but unable to ping or SSH or HTTPS to ACE. Everything seems good. ARP is ok, switch is OK, line is up, protocol is up. Management is enabled for icmp, https, ssh to any.
 
When I do show interface I noticed line  Config download failures : 9.
 
Hardware type is VLAN  MAC address is 00:1e:68:1e:bc:db  Virtual MAC address is 00:0b:fc:fe:1b:01  Mode : routed  IP address is 10.168.0.18 netmask is 255.255.255.128  FT status is active  Description:Management VLAN  MTU: 1500 bytes  Last cleared: never  Last Changed: Mon Jan 21 16:48:54 2013  No of transitions: 5  Alias IP address not set  Peer IP address is 10.168.0.19 Peer IP netmask is 255.255.255.128  Assigned on the physical port, up on the
[Code] ....

View 7 Replies View Related

Cisco :: 5508 Uploaded Via FTP To Controller Successfully

Mar 29, 2012

Web Auth on 5508 running 7.2.103.0.
 
Issue 1: I have been trying to configured Webauth bundle however it seems that is not working.

1. login.tar created use picozip contains 3 files: login.html, terms.html, and logo.jpg.
2, uploaded via FTP to controller successfully..
3, no issue when i tried to preview on the controller
 
However users unable to see the login page when connected to guest wifi. when the user tried to connect cisco.com, on the browser address shows that the page redirected to url... however internet explorer / firefox display "Connection reset error".During this time, if i ask the user to type url... they can see the default login page, so no issue on connectivity to the service port.
 
Issue 2: Since i couldnt make that work, i have use default webauth internal. its all good. then when i tried to upload customlogo.jpg (18k size). User able to see the login page however not the logo.  it shows broken image icon on the web browser. --> i can see the logo when i did preview on the controller.
 
Issue 3: last resort if i couldnt get the answer by sunday, how do i delete or remove the customlogo ?? so by monday users will not be seeing any errors on the page.

View 7 Replies View Related

Servers :: Uploaded HTML Files Can't Be Opened By A Browser?

Jan 22, 2012

I uploaded my web page on Internet via File Zilla. My web page consisted of 10~ HTML files . Some of HTML pages cannot be opened by any browser ( The requested URL /scenos.html was not found on this server ), however, when i open my web locally ( from my hard drive) everything works perfectly

View 3 Replies View Related

Cisco :: RME 4.2 Can't Get Configuration File From ASA5520

Aug 10, 2010

I have a problem with RME 4.2 from CWLMS 3.1. I have configured SSH in my asa 5520 device but RME can't get the configuration file. I ran a job to sync archive but i get this message error:
 
*** Device Details for ASA_5520_VOZ_01 ***  Protocol ==> Unknown / Not Applicable  Selected Protocols with order ==> Telnet,TFTP,SSH  Execution Result: CM0062 Polling ASA_5520_VOZ_01 for changes to configuration.  CM00 Polling not supported on

[Code].....

View 2 Replies View Related

Pulling Configuration File From HP 2900-48G?

Jan 3, 2013

is there a way to pull the config file from this? I tried looking through console mode, but was not able to find an option for it. Or is it just not possible?

View 1 Replies View Related

Copying Configuration File To Usb Storage Device?

Jul 6, 2012

How do i copy the configuration file from a switch to a storage device (USB)

View 1 Replies View Related

Cisco Wireless :: To Download Configuration File Of WLC 4400

Jul 22, 2006

If already saved the configuration file of a WLC 4400 to a server using TFTP? What is the name of the configuration file?

View 2 Replies View Related

Cisco Security :: ASA5520 How To Remove Configuration File

Jul 15, 2007

I want to put the asa5520 to the factory default please let me know how to do that. how to remove the configuration file from it.

View 5 Replies View Related

Cisco Routers :: RV082 V3 - View Configuration File?

Feb 27, 2013

Currently, the backup config is not human readable...any way to convert this?

View 1 Replies View Related

Cisco WAN :: 2950 Switch Receive Configuration File From ISP?

Aug 28, 2012

At home I have a perfectly working test setup for more than 1 year now , but yesterday we had a power down for about 10 minutes in the whole area , after this power down nothing was working in my network any longer.
 
My Network is has follow :
 
ISP(Cable Modem) on FA23 from the CISCO 2950 SWITCH (24 Ports)
ROUTER (ON A STICK) on FA24 from the CISCO 2950 SWITCH
And the rest of the switch is FA1=VLAN 1; FA2=VLAN 2;FA10=VLAN 10
 
Our home network is connected to VLAN 10 with a IP Range of 192.168.10.x /24 After this power down , I was not able to look into the SWITCH via FA1 , the FIX IP in this switch was 192.168.1.251/24, the ONLY way to get access was via the consol port !!!What a suprice when I connected my consol to the PC , I can see ROUTER_F342 , my router config is called ROUTER1841 and my switch config name is /was called SW24.So it seems that after this Power Down , the router took or received a config from my provider ?!?
  
I have recovered the the file in the switch + the vlan.dat and now everithing works again.
 
How can I avoid that this switch receive again a wrong file , I have all the needed files on the products itself and I do not use a TFTP server.
 
I have atached some screen shot when my switch is starting up , and it seems that the switch receive a IP address from my ISP , I do not know why, in the config file I have given it a FIX IP 192.168.1.251/24 ?!?So it seems that my ISP erase the config file and when the switch is empty ,the  swich look for :

tftp://255.255.255.255/router-confg
tftp://255.255.255.255/ciscortr.cfg
Etc ....
Until it find something.
 
I have tried after a complete recovery to switch off the power again for 10 minutes (ISP MODEM + SWITCH + ROUTER) and I was not able to reproduce the fault.Can it be that due to this power failure in our area that some routers or switches send or broadcast this kind of things ?

View 4 Replies View Related

Cisco :: Save Configuration File On 2960-48PST To FTP Server?

Feb 25, 2013

I'm trying to save a configuration file on my 2960-48PST to a FTP server.
 
Unfortunately it doesn't work. What different steps I should follow ?
 
The software version is 12.2(50)SE5.

View 2 Replies View Related

Cisco WAN :: 2811 / 2911 - Use Old Configuration File With New Model Directly?

Dec 11, 2012

We have CISCO2811 model with VWIC2-2MFT-T1/E1 module working good over the E1 line. Since it's getting hard to find new model of CISCO2811 we decided to connect new branches with CISCO2911/K9 model (according to migration doc)
 
My question is can we use 2811's old config file with the 2911 model directly?

View 1 Replies View Related

Cisco Switching/Routing :: C3750 - Running Configuration File

Aug 7, 2008

We have a bunch of switches that are running fine but the running-config file is missing and we can't save the config to the tftp server. IOS is c3550-ipbasek9-mz.122-37.SE1.  I've got lots of these switches running the same code that are just fine.

View 8 Replies View Related

D-Link DIR-615 :: Software Failure - Only 5 LED Lights Responding

Jan 29, 2012

I bought a new DIR-615 and tried to install dd-wrt on it. During the installation all of a sudden the router stopped blinking the led lights and stopped responding to anything. It's current status is that I can only see globe LED and the other 4 LAN LEDs in continuous green and NOT blinking. The power LED and wireless LED are not even displaying. I tried all kinds of reset like soft,hard and crash but no response. It's not responding to anything except those 5 LED lights.

View 1 Replies View Related

Cisco WAN :: 7200 Link Failure Detection

Nov 28, 2012

Primary optical link between CPE and PE, and backup 3G/ADSL link between CPE and PE.I am considering link failure detection on primary link (after which backup link should take over). Which method is the least CPU intesive:
 
1) BGP protocol between CPE and PE
2) RIP protocol between CPE and PE
3) BFD on static routes on PE
 
Is there difference in terms of CPU load between above mentioned methods or they are more or less the same?Hardver platforms are sup720 BXL and Cisco 7200 G2.

View 4 Replies View Related

Cisco Switches :: File Extension For Download Backup Configuration Sg300-10

May 7, 2012

i want to download an backup of the configuration file of my Cisco sg300-10 but do not know what to call the file extension.. backup.??? backup.img? backup.ros ?

View 4 Replies View Related

Cisco Security :: 3310 - NAC Profiler - NetWatch Invalid Configuration File

Jul 18, 2010

I'm trying to configure the NAC Profiler with a 3310 CAS Collector. In the "Edit Collector" menú, it shows all the modules as "Running", except for the NetWatch module which shows a state "Invalid configuration file (missingInternalAddress)".
 
I configured the eth3 interface of the CAS as a monitor interface in the Profiler (see attached image), and I tested that the SPANed traffic actually reaches that interface from the access switch. I'm using software version 3.1.0_24 in both the Profiler and the Collector.

View 2 Replies View Related

Cisco Wireless :: How To Take Backup Of Configuration File For WLAN Controller 4420

Nov 4, 2012

I need to take the backup of configuration file for WLAN Controller 4420, I tried all the possibilities given in the documentation but the backup fails, I have main confusion with the file name to be backedup, i am not able to findout the configuration filename any where even when i use CLI?

View 1 Replies View Related

Cisco Routers :: RV220W - DHCPv6 Prefix Delegation - Editing Configuration File?

Jan 25, 2012

I am trying to configure this router to obtain an IPv6 address from my ISP who offers a dual stack IPv4/IPv6 DHCPv6 Prefix Delegation service.
 
I did a WAN packet capture to see the type of DHCPv6 packets the router sends to the ISP in order to obtain an IPv6 address and I saw that the router is sending DHCPv6 solicitation packets of type IA_NA i.e. for Identity Association for Non-temporary Address. However, most ISPs that offer a dual stack IP4/IPv6 service, they use DHCPv6 Prefix Delegation in which case the router is expected to send DHCPv6 solicitation packets of type IA_PD i.e. for Identity Association for Prefix Delegation.
 
I then downloaded its configuration file and saw the following:
 
dhcpv6c = {}
dhcpv6c[1] = {}
dhcpv6c[1]["renewTime"] = "3600"

[Code].....
 
So, the option for the DHCPv6 client to perform a prefixDelegation request is disabled. Does that mean that if I set this flag to "1" it is going to work? Well, I edited the configuration file and changed this flag but the router refuses to load it! It complains about the file being changed. How does it know that? Is it computing some type of checksum? How can I manually edit this flag and update the router's configuration?

View 2 Replies View Related

D-Link DIR-655 :: Boot Failure After Failed Firmware Upgrade Through Chrome

Feb 12, 2011

I've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.

View 2 Replies View Related

Cisco Switching/Routing :: 650x How To Improve Link Failure

Jan 27, 2013

I have implemented in my company network recommended by cisco scheme with MEC etherchannel from some segment distribution layer (VSS) to core switches (legacy 650x) exactly as on picture: Core switches  have rather old  IOS (Version 12.2(33)SRB4 and i have reasons not to upgrade it now) which dont support many functions - like BFD over Etherchannels and Enhanced PAgP. And we run a OSPF/MP-BGP/MPLS bunch over those links with OSPF reference bandwidth configured to such values that failure of one link in etherchannel will not lead to link cost changes (we dont have a lot of traffic for now on those links and 1 link can handle it easily) and consequently will not trigger changes to RIB and BGP topology table.
 
Problem is that i am afraid that in case of one of link of portchannel will fail (but without port down event - unidirectional link or smth else) it will take rather long time to converge - and im talking about L2, not L3 protocols. Cos i cant implement BFD and ePaGP over this link - best i can do that improve 30 seconds PAgP hello timer to 1 second. But at least 3 seconds of possible traffic blackholed - is rather big problem.First time i considered 2 possible solutions:

1) BFD - but even i can use it, it will not improve much recovery time cos 750 ms for BFD over etherchannel not much better that 1 second PaGP fast timer.

2) ePAgP - as i understand this protocol have enhancements to discover failed link faster and improve recovery time, but all information i can find about it - is how to use it for dual active detection and none about timers improvements. So i cant be sure that i should upgrade IOS on Core switches and it will improve my failure detection time. ( if it possible adduce some links to description of this protocol enhancements in comparison with PAGP)
 
For now im already thinking about using four L3 links (instead of 2 portchannels) and BFD over those links with 50 ms hello timer. But in case of link failure reconvergence of OSPF will take some time, and BGP will react to this no immediately, so i am afraid that even using aggressive timers for routing processes and hellos i will not win much time.

View 1 Replies View Related

Cisco Switching/Routing :: Port Down (Link Failure) On FEX (2232TM)

Jan 8, 2013

We have FEX (2232TM) connected with 2 x NEXUS N5K-C5596UP.
 
One port  Ethernet 101/1/7 which was connected to Dell Server went down...
 
It was working for a couple of weeks at least. Then the link went down and now I'm unable to get anything connected to this port As I said, this already happened before, but unfortunately I can't remember if it was on the same port/fex ... from the fex uptime it seems that this was on another fex I was able to get the link back up by doing a power cycle of the fex
 
At the moment Dell server is connected to different port Ethernet101/1/4.. See config bellow:
 
. config, how ports are configured
 
interface Ethernet101/1/7
description VM008 Network 1
switchport mode trunk

[Code].....

View 7 Replies View Related

System Restored Computer Now It Won't Connect To Internet?

Jan 5, 2013

I recently system restored my computer, and it was connected fine to my d-link DIR-615 router, but now it does not connect, what do i do?

View 14 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR740N Failure To Connect To Internet / Server

Apr 24, 2013

Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version :
Firmware Version :
ISP :

I've configured the router using the Easy Setup Assistant CD provided and have a wifi connection between the router provided however when using network diagnostics, while the wifi connection is fine, I am getting "failed to connect to Internet" and "failed to connect to server" messages. I have tried adjusting settings manually but without any progress.

View 8 Replies View Related

Restored Laptop To Original Settings - Not Responding Error?

Apr 16, 2011

Now I am having major issues,running super slow and can't connect to ie. Keeps giving error not responding

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved