D-Link DIR-825 :: Firmware Upgrade To 2.05NA - Bad Flash
Feb 6, 2011
I hope that we can get this DIR-825 back from the dead. I did the first portion of the 2.05NA upgrade while wired into LAN1 on the unit, after the reboot the power light went Amber and the unit would no longer respond to pings. I have searched around for various reset methods but have not been able to find a guide or a definitive current D-Link tech manual on how to fix a bad flash. I have tried pinging/arping/web browsing its default IP and the IP I had it set to to no avail.
I have a Dlink DIR-825 B1 with firmware 2.05NA. I recently reset it to factory defaults to make sure I didn't misconfigure something.
I have been struggling to get a IPv6 in IPv4 tunnel working with tunnelbroker.net. I think the issue is a problem with the router itself and i'm not sure how to get it fixed.
All of my machines were getting IPv6 addresses (both windows, mac, linux) but none of them seemed to work. All I was able to do was ping the gateway itself using the local lan address. In each case they were missing a default IPv6 route. If I added a default route then it would work.
I started looking at the packets using a network sniffer and the Router Advertisements all had a Router lifetime value of "0" which is RFC4816 speak for "don't use this router as the default router". So Windows/Linux is exactly right by not setting a default route.
The strange thing was that when I reboot the router I would briefly get a router advertisement with a lifetime of 1800s, the corrert prefix and dns server but then another router advertisement would come along 5 seconds later with a router advertisement of 0.
I have TCP' Other observations
... using 6to4 I would get working IPv6 address. The difference again seemed to be the Router Lifetime. But I want to use a permanent tunnel. I have found 6to4 unreliable.
... the router never responds to router solicitations. It only sends a router advertisement when it wants to.
... the router never responds to DHCPv6 when that is configured.
I've got three WG302s of which the certificates on all of them are up. I've begun the process of replacing the firmware on one of them with OpenWrt. I've been using this to get the job done: url...I've been able to edit it up to the point of using fconfig to edit the boot script. I understand that I just need to edit two lines and the firmware replacement will be complete. [code]I've looked up fconfig commands to see if I could figure out how to edit the script lines.
I recently updated my firmware to dd-wrt... now I would like to switch back to stock firmware. I don't like the fact that any change I make basically resets the router. Plus DD-WRT GUI is VERY slow for me?I've followed every tutorial on how to do this, but the router will not accept the stock firmware. I've gotten the image to upload (according to the browser), but at 100% the flashing orange light & globe light just continue to blink & do nothing. I never see the other lights "flash" confirming the upgrade has took. I've set my IP manually through "Network Connections>Properties>TCP/IPv4" before trying. I get to the emergency firmware page...set it upload Version A1. Sometimes it uploads...but like I said, it never takes.
I tried to upgrade to 2.05NA several times and there always ends up being an issue that support is too sad to give the correct answer to and just puts a consumer thru "jumping thru hoops" and getting nowhere.2.05NA (actually started with 2.03NA) first caused a problem with limiting my upload speed to 1024mb. I happened across the fix on another forum and tried it and it worked. It was the default QoS setting D-Link changed after version 2.02NA and refuses to release a new firmware to fix this for everyone. Why they don't release a new FW that fixes the issue but keeps things promised on the package working is beyond me. Now, I purchased a D-Link DNS-323 and I finally got drives to fill it some time back. If 2.05NA is loaded, the Easy Search Utility will not connect to the NAS. I have tried the version the NAS came with AND the latest version offered. It will see the NAS upon 1st launch of the latest Easy Search Utility, but it will not connect and then it disappears if you relaunch the utility and won't return until a reboot. Bottom Line: it will not connect with 2.05NA loaded. It works fine with 2.02NA.
What is the setting that D-Link has screwed over here also that is causing this problem? It is pretty sad that their own hardware items won't play well together unless you run old FW. What setting D-Link changed that is making the D-Link DIR-825 not connect to the D-Link DNS-323 NAS when the DIR-825 has 2.05NA loaded. I have a DIR-825 Rev. B1 and a DNS-323 NAS with its latest firmware. I am using 2.02NA on the router since that is the only one that works and is the latest stable release(other than the DHCP reserve issue), no matter what D-Link wants to try to make people think. I won't try their support since they NEVER did give me the fix for the QoS upload issue and when I asked them to put it as a sticky in this forum when I found the answer somewhere else....well, there is no sticky as we all know. I would like to be able to have the DHCP Reserve issue working too, but I would like to connect to my NAS more at this point.
I have a Dir-655 A3 with the firmware 1.32NA. I cannot get the new firmware 1.35NA to take. The router seems to go through the motions of the upgrade, but at the end, when I log back on, the firmware still says 1.32NA & all custom settings remain.I have upgraded the firmware on this router before and I know that when its upgraded, the router is basically reset to factory settings. All the settings have been backed up and I am attempting this upgrade via a wired connection.
I have a DIR-655 Rev A4.I followed this forum in the past when there were many problems with firmware upgrades beyon 1.21. Because of this I never upgraded and was told to be satisfied that I can still stay with 1.21 as upgrades caused problems for a number of people.Everything still seems fine with 1.21 except the Shareport utility often does not pickup the printer connection upon booting to Windows Vista. I can always work around this by Disable and then Enable. It will then always find the printer. It is a minor annoyance however.Should I still stay with 1.21 or is upgrading to 1.35 NA recommended ? If I upgrade to 1.35 NA is there a downgrade path back to 1.21 if the upgrade does not work well ?
Have the DIR-655 Hardware Version A1. Firmware 1.00NA dated Feb 2010. When I try to upload ANY firmware update from the DLINK site, it says that it is not for that device or is corrupt.
I have the DIR-655 . I decided to do a firmware update to Firmware Version: 1.35NA and now I having a problem connecting remotely from outside the network to a computer on my LAN. I use a software called Radmin to connect to one of my LAN computers behind the DIR-655 router and now since I did the update I cannot connect because the router is blocking the request, here is the router log info
I have a DIR-615 Ver. C1 f/w3.00. We have been having trouble with the the signal becoming weak or non-existent, so I decided to see if a firmware upgrade would solve the problem. I have attempted to upgrade to DIR615C1C2_FW301B11.bin and to DIR615C1_FW313NAB09.bin with the same result for both of them - with several attempts for each.
The message I get is: "The uploaded firmware file may not be correct. You may have uploaded a file that is not intended for this device, or the uploaded file may be corrupted.
If the uploaded file is correct, it is possible that the device may be too busy to properly receive it right now. In this case, please try the upload again. It is also possible that you are logged in as a 'user' instead of an 'admin' - only administrators can upload new firmware.
The Gateway will not be reprogrammed."
I have disconnected all other devices to reduce traffic, I have attempted the upload multiple times for 3.01 and 3.13NA, I am logged in as the admin, and I believe the files are proper for this hardware version.
Is there something I am missing that prevents me from performing a firmware upgrade?
Well this one should be in the "Firmware DOs and DONTs" post. I updated to FW 1.11 over wifi and apparently this will corrupt the camera so it needs serviving. Would have been nice to know that before I did it. Since the upgrade from 1.02 1030 I get this note:The throughput of the SD Card on your camera is not currently enough for recording. We suggest you to reformat the SD Card or replace it with a higher class one.
I wanted to upgrade to the latest firmware (2.03NA). Something went wrong and now the router comes up with the orange light flashing. So the system is in emergency firmware upgrade mode. I set my IP to 192.168.0.2 and connect to the web interface at 192.168.0.1. I see a page with "Firmware Upgrade System" and "Version 1.0.0.2". So far so good. I can now select the firmware and click "send". But then nothing really happens. I can wait for a couple of minutes and then run into a timeout. I tried different browsers (Linux: Firefox, Chrome, etc). I even tried it Windows 7 with IE 8 and I get the same result. It seems that the cgi (192.168.0.1./cgi/index) is not really doing anything?
Last week I upgraded the firmware to 1.13NA and ever since, the wireless network has been slooooooow (wired is fine). If the laptop/ipad/phone is in the same room as the router, things are fine. Anywhere else in the house, the speed drops off to almost nothing even though the signal strength is very good. For example: Under the "Speed" section of my "Wireless Network Connection Status" on my laptop, I'm seeing 150.0Mbps in the same room as the router, 25.0 Mbps in the hallway and 1.0 Mbps about 5 steps further away. All the while, the signal strength is showing Excellent.Speakeasy speedtest: Wired 23.36 Mbps, wireless at the end of the hallway, .12 Mbps.
I would upgrade the firmware before deciding to replace router with a new one. I noticed there have been several updates to the firmware since I originally installed the router with the current available firmware version of 1.35NA.
I tried to download the latest firmware from this page (V4) [URL] I press browse button from web interface, I select wr641gv4-en-up.bin and I press Upgrade but nothings happened. I read on other forums this router have 1MB internal memory and wr641gv4-en-up.bin have 1.07MB.
Region : India Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : 3.14.2 Build 120822 Rel.57775n ISP : BSNL EVDO
I have one BSNL EVDO data card which was working fine before firmware upgrade to latest 3.14.2 Build 120822 Rel.57775n. Now it is keep on saying device unplugged after identifying the device. The device is working fine while connected on my laptop.
Model : TD-W8961ND Hardware Version : V1 Firmware Version : 100722 ISP : Talk Talk
I've downloaded the firmware update 111125 and followed the instructions. The progress bar reaches 100% but the router doesn't seem to restart (judging by the status lights on the front). It does ask me to log back in but when I check the firmware version, it still reads 100722. I also tried factory default settings after the update. Still it reads 100722. I've tried the update 3 times now.
I've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
first one had to get rid of because just wouldn't work with a 3CX server, anyway, I have a DIR-655 A4 factory shipped with 1.32NA I am trying to update the firmware to 1.34NA but it will not let me. It keeps saying Code:
I have a DCS-942L. Everything was working fine on my setup until I upgraded the firmware the other day. In the mydlink.com website when I logged in that day, it stated a firmware upgraded was needed. So I clicked on upgrade, let it run its thing and then tried to view the playback and now the thumbnails are just black and when I click on one, it looks like it is loading but then shows the quicktime icon with a question mark over it. I upgraded my Quicktime component and that didn't fix it either. So I went into advanced settings, downloaded the new firmware upgrade from there by saving the zip file and uploading it via the advanced settings website, and still nothing. I have another camera, same setup, that I have not upgraded firmware on yet and that playback is working fine.
Region : UnitedKingdom Model : TL-WR1042ND Hardware Version : V1 Firmware Version : 3-14-4 to 3-15-4 ISP : Primus Saver
I had it all working fine, then I wanted to upgrade the firmware. The original firmware was 3-14-4. I downloaded and applied the 3-15-4 firmware. Now when it powers on the power light is on all the time. Immediately the sys, 4, 3, 2, 1, Internet, usb and wps lights flash once. Then about 5 seconds later the 4, 3, 2, 1 & Internet lights flash once, then a second later the cycle starts again. When I connect it to the PC it starts to make a connection on the NIC, but then the router resets. Model: TL-WR1042ND, Ver 1.3 . Is there a way to reset the firmware or get it working again?
I recently upgraded my DIR-655 to firmware version 2.10NA , 17, Oct, 2012.Ever since the upgrade, on a wired connection the router will occasionally not serve pages. This shows up as a DNS error, stating the DNS lookup failed. If I wait a bit and reload the page, it will sometimes resolve itself. If I bypass the router and plug directly into the modem, the problem goes away completely.This is happening on my MacBook Pro, OS X 10.7.5, any browser (I use Chrome mostly, but also Safari and Firefox have the same issue). This is not happening on my Linux laptop which I use wirelessly, or my iPhone or any of my wireless clients, though the same MacBook occasionally has trouble connecting if I DO try to use it wirelessly (I receive a connection timeout and cannot log on). I'm not certain at this point if the trouble is with the router or the computer, but it only began happening (and happened immediately) after I installed the most recent firmware.
My security setup, if for any reason it matters, is WPA2 with MAC address filtering.
So let me start by saying that i'm stupid, as i did not 1st read the manual properly and thus upgraded my camera WIRELESS.. (when manual clearly states by cable ONLY).
Camera is now DEAD. Only red led light is flashing.
Hardreboot not working (pushing reset, then switching on camera & hold reset for 30 secs)
Is there anything else that i can do myself or is this gonna be a repair job?
Region : Bulgaria Model : TL-WR2543ND Hardware Version : V1 Firmware Version : ISP :
Region : Others Model : TL-WR2543ND Hardware Version : V1 Firmware Version : 3.13.6 Build 110923 Rel.53137n ISP :
I bought the TL-R2543ND. The hardware version is V1.2. I want to ask, is there firmware upgrading for this version . Here I see only version V1. [URL] Are they suitable for my router?
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 1 ISP : cox.net
I have downloaded the file TL-wdr3600_v1_130129.zip. Extracted the file to a temp folder. Thje file is a bin file which is a bin image wdr3600v1_en_3_13_26_up(1301).bin. I do not see any flash file to load this to the router.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 121225 Rel.37950n ISP : Comcast
just upgrade to the latest firmware and was checking to see if I had IPv6 going with the router but it seems like it's not enabled?I went into my local area network properties and it shows checked and obtain automatically.went into the router ipv6 support tab and it shows:
IPv6 Status WAN Connection Type: DHCPv6 IPv6 Address:
Region : Others Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 1.8 ISP :
Region : Israel Model : TL-WR1043ND Hardware Version (On the back cover): V1.8 From web interface: Firmware Version:3.13.4 Build 110429 Rel.36959n Hardware Version:WR1043ND v1 00000000 ISP : Free
1. about USB Printer Controller
I connect my printer HP office jet 5610 All in one, his drivers installed on my computer (windows 7 ultimate, 32 bit). Irun the software "USB Printer Controller" and i didn't seeing anything. Can not click on any button. BTW, i changed the IP range from 192.168.1.1 to 10.0.0.100-10.0.0.139 and my router web interface at 10.0.0.140, if it's changing something.
2. About upgrade the router's firmware, it's safe that I'll upgrading it?
I've not found any topic related to what happened to me. Bought two cameras and upgraded the firmware on both as asked, but one of them just stopped. The light is solid green and not red like other posts.Tried the recovery procedure, but the browser won't find my camera. Changed computer IP and everything else that was told to be done. Nothing works!! I also can't find any posts relaled to my problem all over the internet.
Region : UnitedKingdom Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP :
After setting up the newly arrived router, renaming the SSID and changing password for 2.4 GHZ AND 5 GHZ and also renaming the default router username and password, I decided to update the firmware.The procedure wiped all configuration I've made forcing me to do all over again.
