I've had this router for a few months after my last one died and I'm now completely unable to port forward. I follow all the steps to port forward but alas the port is still closed every single time. I've tried a few fixes in the past including disabling UPnP, using those auto port forwarding programs, and creating an exception for the port in my fire wall. Nothing has worked!
View 14 RepliesI've installed XAMPP on one of my Vista computers, and intend to use it as a server. The internal IP address of the server is A.B.C.D. The internal IP address of the DIR-615 is A.B.C.E. whatsmyip.com says that external address of the server is F.G.H.I (and so is everything else inside my network). I have Filezilla listening on port 21. I've turned Windows Firewall completely off on the server, and my ISP (Time Warner / Road Runner) says that they never block any port.I tried going to the DIR-615 using Port Forwarding, and set ports 21 & 90 to forward to A.B.C.D, for both UDP & TCP, Allow All, Always. That didn't work.I tried going to the DIR-615 using Virtual Server. I set a virtual server on port 21 to A.B.C.D, for both UDP & TCP, Allow All, Always. It made me turn off Port Forwarding, and it wouldn't let me use both 21 & 90 on the same rule, so made two rules. That didn't work either.
I tried setting A.B.C.D as a DMZ host. That still didn't work.I can ftp connect into A.B.C.D from one of the other computers in the network. People outside the network can't connect to F.G.H.I. I can't connect to F.G.H.I. from inside the network. The same is true of Apache (but ports 80, 81 & 443), Ventrilo (but ports 3784 & 6100) and MySQL (but port 3306). I figure that FTP is the easiest to test, so I've been just trying to get that to work.In FileZilla Server Options, I am bound to *, I have no filters, and my passive mode is set to "Retrieve external IP"As far as I can tell, if I've ruled out anything inside my network (by connecting internally), and I've ruled out my ISP (they don't block), then it must be the router. I think I've done port forwarding according to [URL], and it seems like it should be easy, but I've been trying forever and I can never get it to work.
I'm trying to get the silly iTunes Wi-Fi sync to work , and I've been told to ensure that these ports are open:5297 TCP 5298 TCP/UDP and 5353 UDP in the hardware router. How do I do this with the DIR-655 (HW version A3, FW version 1.35NA)?
View 1 Replies View RelatedWe have a DVR here at work that has a web interface on port 100. From our internal network we just use http:192.168.100.40:100. What is the best way to set that up on cisco 5510 firewall. I have cisco asdm and set a access rule: enabled=checked ; source=any ; destination= 192.168.100.40 ; service= tcp 100 ; action=permit. It shows a couple of hits when I go to [URL]
View 7 Replies View RelatedWhat I'm trying to do is to get my Xbox connected to the internet through my router (wired connection), but I want to have my NAT open also. But when I put in a static IP into the Xbox manually and open the ports in my router, it makes it so my Xbox can't connect to Xbox Live at all. Although, if I just leave it to the automatic setting on my Xboxs network options, I can connect just fine. But, I end up having a strict NAT type, unless I restore to factory defaults in the networking options on the Xbox.
View 2 Replies View Relatedhow can I open my port 80, 5000, and 22 in my modem.
View 1 Replies View RelatedI have been asked to open some ports in order for a CCTV company to connect to an internal CCTV server on our LAN.
We have a Pix running PIX Version 6.3(5) I am ok configuring an ASA for the above but not a Pix.
I am trying to configure a new 5505 but I am having difficulties opening ports that allow traffic in from the outside. My setup is Comcast Business Modem (w/ single static IP) -> ASA (10.0.0.1) -> (dumb) Switch -> NAS (10.0.0.10). I am attemping to open port 5001 to the NAS. I am very new to IOS so I have mostly been working in ASDM. Not sure if I am overcomplicating this for myself or what but I am stuck.
My running config is -
ASA Version 8.2(5)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
[Code].....
I just purchased a cisco ea4500 I have set up port forwarding for http, https, rdp. however when I run zenmap and port check it fails says port in use. I have set it up in sigle port forwarding, rang and port trigging. I tried RDP and VPN to machine that is hard wired and it fails as well. My windows server is connected as well however RDP fails on there to
View 9 Replies View RelatedI need to open some outbound ports in order for our CCTV company to receive alarms from our internal CCTV Machine.
The ip addresses of the company who access the CCTV are as follows:
213.130.134.56
81.130.198.97
The above are fixed IP addresses. The internal machine is on 192.168.204.170
The outbound ports that I need to open are the following:
TCP
21
23
80
5201
UDP
1025
2074
2075
I have access to the current config if needs be.
I need opening up some ports for a sftp client at work. software version 8.0 (3) device manager version 6.1 (1)
View 4 Replies View RelatedI have a Belkin F5D8233-4v3 N Wireless Router. To get the wireless Directv connection, directv told me I have to get 2 ports open on my router.1701 and LT2P.
View 1 Replies View RelatedWe have just acquired a cisco profile 42 video conferencing equipment and am required to open ports for SIP and H232, any pointers on hw that can be acquired i have a cisco ASA 5510, Some one told me to open port 16384 but i need pointers on how to do it becuase I already set an access list to any.
the config
Internet -> ASA 5510 -> Switch -> Profile 42 and other devices
I am trying to open up 3 TCP ports in Cisco ASDM Launcher:
16000
16001
8098
And have a Cisco ASA 5505 Router. I need these ports open in order for a software that I have installed on the server to communicate with my local client computers for my business, The software is installed on Windows 2008 Server Standard Edition and was installed with MicrosoftSQL 2005. The software and Microsft SQL 2005 is pretty much installed and just requires this last step in order for the server to be connected to the local computers. In order to resolve this, I have gone to.
I am used to setting up access-lists on outside interfaces with ip addresses that are static. I have recently been given a site that is using a dyndns.org client for name to ip address resolution on an outside interface that is dhcp assigned. I created an access-list to open up ports 41794 and 41795 to an engineering application but everytime I try to connect from the outside I get a syn timeout. The application works when inside the lan. Basically I want to allow outside connections from anywhere on the outside to go to ports 41794 and 41795. I am running a Cisco ASA 5505 on version 7.2(4) Below is my conifg. what I may have misconfigured?
: Saved:ASA Version 7.2(4)!names!interface Vlan1 nameif inside security-level 100 ip address 172.31.2.1 255.255.255.0!interface Vlan2 nameif outside security-level 0 ip address dhcp setroute!interface Ethernet0/0 switchport access vlan 2!interface
[Code].....
I have a cable modem hooked up to a Linksys WRT54G2 wireless router, which is hardwired to the computer I use.
I go into the router's menu by going through the standard 192.168.1.1 in the browser, and then go to Applications and Gaming. The port I am trying to open is port 25565 for both TCP and UDP. In the Start and End ports I put 25565, and for the end of the IP Address, I put the last digits of my IPv4 address (10). I used a couple of port checker tools, and it is reporting as still being closed.
Any simple way of opening ports on a 1841 router.I have a working config for internet traffic. I am looking to boot up my Windows Server and Run IIS.
View 1 Replies View RelatedI have a Belkin Play N300 (part number = F7D4302) wireless router, and I want to connect my (soon-to-be-pole-mounted) 12DBI omnidirectional antenna to it, the goal is better wireless access in one area of a church camp. I have a couple of U.lf - RP-SMA pigtails on the way, because of course the router doesn't have an external antenna connection.
I opened up the router case, and below is a shot of the board. There's plenty of room inside the case. The router is dual-band (2.4 and 5ghz), and uses 2 internal antennae, apparently it senses the better one and uses it as needed.
My plan is to disconnect one antenna, and connect/solder my external antenna pigtail in its place. I'm a fair hand at soldering, but very little practice de-soldering...
1. Is disconnecting / replacing one antenna the way to go, and if so, which one? Or should I leave them both connected and piggyback my external onto one of them (soldering the leads on top of existing connections), or disconnect both antennae, or does it matter?
2. Which set of wires, white or black, are used for which band - and should I connect to? I assume I'd want to hook up to the 2.4ghz, correct?
The white wires come out from the tiny Broadcom chip, I think it's marked BCM43224KMLG (dang, that's some tiny print!). This page leads me to think that these are the 5ghz antenna leads, but I'd llike to be positive before I start cutting.
The black wires appear to feed from the larger Broadcom chip marked BCM4718A1KFBG. Again, this page leads me to think that this is the 2.4ghz antenna.
3. Assuming that the black wires are the ones I want, would it be ok to cut one really close to the board end, cut the U.fl connector off of my pigtail, prep the wire / shielding, and solder the wire / shielding on top of the existing solder connection?
A customer got a new VoIP PBX, and now I have to forward port 443 on the ASA to the PBX for remote administration purposes. The LAN-interface of the PBX is in the same subnet as the ASA but has an external VoIP-router as default gateway and not our ASA. Is it even possible to forward the port to the PBX when there is no route of any sort to our ASA on it?
View 2 Replies View RelatedWe have a setup where our e-mail server is hosted in-house.Our network is connected through a RV042 gateway. Port 25 is forwarded to our internal e-mail server.Our smtp service should be limited to receiving incomming connections only from 4 specific ip ranges which I set up in the firewall rules.The reason is that all smtp is managed and protected by an external anti-spam/vires provider.
However it looks like any computer is able to connect to our port 25 and be forwarded to our e-mail server.Does portforwarding overrule firewall rules - ie. you can not limit access with the firewall if you decide to port forward?Is this a "fixable" situation - or is the RV042 not built for handling this setup?
Region : Vietnam
Model : TL-WR841N
Hardware Version : V8
Firmware Version :
ISP : VNPT on Vietnam
I have bought WR841 V8.3. Signal show is good, but i ping to router many timeout or delay when i open some website. Ping only geog when i near router.(some time delay)
One of techs accidentally connected two access ports from different switches together. Since then, LMS is alerting them as being Link ports down. I tried to default the config and set them to access ports without any success. what I should do in LMS to recognize them as access ports?
View 2 Replies View RelatedI have this problem i can't open my ports on my D-link 524, i have opened about 6 ports so that my XBOX 360 works with a open nat, i have also set the DMZ to my xbox's IP which is static btw, my PC is also static. This is how i basically tested and it told me that it was not opened. I went into:
192.168.0.1 -> Advanced -> Virtual Servers ->
Enabled
Name: XBL1
Private IP: 192.168.0.100 ( because i was testing it on the computer - if it
were 360 it would be .141 )
Both UDP and TCP at port 3074
Schedule=Always
Apply -> Then restarts modem/router i waited for 2 minutes before turning them on again, i turned router on first because some guide told me to do that.
I did exactly what they did on portforwarding.com then i opened up portchecker and typed in 3074 and pressed check -> This port is NOT opened. What is wrong? This is how my net is set up.
Modem ZyXEL -> D-Link 524 -> D-Link DGS 1005D -> Computer/XBOX.
I can't get port forwarding to work, even when I turn off the Windows 7 firewall and AVG anti-virus software I'm running. I entered the IP address of my laptop (with a DHCP reservation) and UDP and TCP port numbers, with Schedule set to Always and Inbound Filter set to Allow All. That should be it, right? However, when I check the ports using PFPortChecker, both the UDP and TCP ports are blocked. I do have a Linksys wireless router daisy-chained to the D-Link router, but I'm not communicating on this computer through the Linksys router and the problem still occurs even when the other router is disconnected, so that doesn't appear to have anything to do with the problem. I just updated to the latest firmware (3.13NA).
View 11 Replies View RelatedI want to open MORE than the 24 ports that the router configuration allows (DIR-615 Hardware Version: C2 Firmware Version: 3.03RU)?
View 14 Replies View Relatedcant open the ports 2300 -2400 (udp, tcp)on router. What I do isthe following.
1. Open ports on router in port forwarding.
2. Add the triggers as well in APPLICATION RULES with the ports. Triggers are 47624 and 6073.
3. Try both Dis and Enable UPNP. Even try the DMZ enabled settings.
4. Disabling firewalls on Laptop and router. Try both ways on DMZ's(enable and disable) settings on router. Check everything.
Still when I check on websites about the ports and they are shown closed (NOT STEALTH). Router uses a firmware 4.0. I have a windows 7 64 bit system. I use wireless.
Note: All the steps are performed in a combinations manner to see if there is any possibility of opening ports.
I want to forwards some ports for my PS3 however. I am using [URL] to do it. I use IE, I go to port forward, I set everything up like it shows and put in my PS3 IP, and I choose save settings. When it comes back after rebooting, nothing is saved. Everything I put in has vanished.
View 5 Replies View Relatedi've tried plugging in various devices (computer & solar panel management device) into the ethernet ports to no avail. i just updated the firmware, reset the router, and still no luck. all of the lights work when i reset and the wifi works fine. do i need to do something in the settings to turn on the hard connection?
View 3 Replies View RelatedPorts are still closed after forwarding them dont know why am using TP-LINK WR740N.
View 3 Replies View Related1.) I don't have a wireless card in my PC, so I will be connecting wired to get WiFi via WAN and LAN ports, right? I have a Windows 7 32-bit desktop PC. We are working with a DSL modem residential line without phone line using a coaxial cable, and Ethernet cable from modem into the PC. provide step by step walk through instructions by connecting this D-link router to my modem and WiFi, and for me to use the WPA2 security?
2.) I have an iPhone 4 with Verizon. If I want to use my iPhone to get WiFi from the router, and turn off the Internet, and use WiFi only on my phone, how would this work?
I have been trying to block access to Steam and Left 4 Dead 2 on a specific computer, using the correct listed ports and using the port forwarding section of the router (setting the access to deny) however they seem to still be able to access both steam and L4D2 on their computer.how I can still block the access?
View 1 Replies View RelatedRegion : Others
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
Region : Sweden
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
opening of some ports 25565 for minecraft so i can host games. i have try so solve this by my self but with zero progress. did enter the advanced setup and then i pressed on the NAT category and then i pressed on the ADD button and enter the following" [URL] and then i used a port checker to look if it worked but did not work?
My router is on a static IP, it is a Linksys WRT150N, and it doesn't have gigabit ports. Is it possible to run it through the 1522's gigabit ports.Modem -> 1522 -> actual router.
View 2 Replies View Related