I want to forwards some ports for my PS3 however. I am using [URL] to do it. I use IE, I go to port forward, I set everything up like it shows and put in my PS3 IP, and I choose save settings. When it comes back after rebooting, nothing is saved. Everything I put in has vanished.
View 5 RepliesWhat is the name or path for the file stored on your hard drive for the configuration settings?
View 7 Replies View RelatedI just got a DCS-930L camera. I was able to set the password (10 characters) and complete the setup. It then said I needed to update the firmware which I did and it successfully completed. I was able to access it through the mydlink web page but when I clicked on the advanced settings, it wouldn't log in. I tried running the setup from the CD but it said "There was a problem saving your settings. Click Next to try again." That never worked. I tried a hard reset, no luck.
View 3 Replies View Related2 days ago bought 2 dlink 930l camera's. Everytime a reset or reboot the camera or maybe not even reboot the date and time for the camera is far away, so it is not saved. I am not using yet a ntp server because i don't now which one yet.
View 3 Replies View RelatedIs it possible to load the configuration from a saved configuration file from a DIR-625 to a DIR-825? If so, what steps are required?
View 1 Replies View RelatedIn have the 942l and the mydlink Lite app on the iPhone. I have recording set up on the camera capturing in .mp4 format. I can view the camera on the phone fine. I can go the menu and select playback. I see the date of my recordings and the time. Each individual file is listed as you can see.
When I select any of these files, I get a black screen.
Do I need to change the rtsp URL? Anyone have this working correctly on the iPhone? If so, can you share your settings?
One of techs accidentally connected two access ports from different switches together. Since then, LMS is alerting them as being Link ports down. I tried to default the config and set them to access ports without any success. what I should do in LMS to recognize them as access ports?
View 2 Replies View RelatedI have followed directions and forwarded the two ports to the local machine. I looked in the router setup to find my current public ip address from Comcast say its 98.221.99.99. If I am on the same network as the machine that is receiving the port forwards, and I type http:// 98.221.99.99 in a browser, the forwarding works fine.If I am external/not on the same network, typing http:// 98.221.99.99 in a browser times out. I have tried http:// 98.221.99.99:9000 too (9000 is the port I need forwarded) and that doesn work either.But, I do have remote management enabled for the router and if I am external/not on the same network and I enter http:// 98.221.99.99:8080 in a browser, I get the router login screen and can enter my user name and password and login to the router just fine.
View 11 Replies View RelatedI'm using PfSense 2.0.1. What im trying to do is connect to a game server I have running here in my house. I can connect to it locally with 192.168.8.6 no problem. I have it port forward correctly so that the rest of the world can connect to it via my WAN ip address. The problem comes is I want to be able to connect to it with my WAN address so that if someone decides to follow me STEAM will show my WAN address not my internal IP address of the server im connected to. I have "Disable NAT Reflection for port forwards" UNCHECKED which is what I am supposed to do according to documentation from PfSEnse. But it still doesn't seem to work.
View 5 Replies View RelatedI am building a new VPN Anyconnect solution. I want the traffic to enter a interface and that traffic should be forwarded to my "VPN-Machine".
The system is a ASA5520 with old software, I am not at work now so i cannot tell exactly.
So my question is, how do i make the traffic enter one interface and being forwarded to another? I have splitted the physical interface to several sub-interfaces.
Linksys BEFSR41 4.2 Main router 192.168.2.1, if I cascaded a second Linksys BEFSR41 4.2 LAN to LAN 192.168.2.2 would I be able to port forward on the second router? I need more than 10 port forwards.and if so would I have to set the second router up with the internet provider log in and password like the first router?
View 4 Replies View RelatedI am trying to set up a Cisco ASA 5510 running 8.2 to allow a connection to a Polycom camera that sits behind it. What I want to do is forward multiple ports to allow a connection from an outside office. The polycom camera uses the following ports:
1720 tcp
3230-3235 tcp
3230-3253 udp
I got these port numbers from the Polycom web site. So what I did was create a service object as follows:
object-group service All-Polycom-ports
service-object tcp range 3230 3235
service-object tcp eq h323
service-object udp range 3230 3253 My question is how can I use this service object in a static (inside,outside)
command so that I don't have to create multiple commands for the port forwarding. Is this even possible or do I have to sit down and write out around 30 seperate commands to do this. I've been searching the web and it seems a lot of people want to do this but so far I haven't found an answer.
Background: currently have a WRT320N, thinking of upgrading to an EA4500 assuming ONE feature has been improved: Port Forwarding.
Scenario: Currently I have a WRT320N router, and while it "does everything we need" it has one limitation that is now getting in the way: limitation on number of forwardable ports. In the port forwarding panel, it has 15 total rows: the first five rows can be enabled for specificaly named services (SMTP, FTP, etc). The last 10 rows are fully customizable in that we can set the name, ports and protocol.
The problem is that of the 13 total ports I currently need to forward, only ONE of them is listed in that fixed list. So, sadly, I can only use one of those first five rows. I've now filled the remaining ten custom rows, and still have need for two additional ports (for now, may need more down the road).
Trying to get creative, I figured maybe I could just spill over to the Port Range Forwarding page and add a row or two there. The only problem: it's buggy. I've found that if the Single Port Forwarding list is filled, then the Port Forwarding Range entries don't work properly. For example, if I wanted ports 12345 and 12346 forwarded to 192.168.1.5, they work fine with two single port forwarding entries. However, if I delete those, add two other port lines I need forwarded (the single list being full again), and add a port forwarding range 12345..12346, they don't work properly, ports just are closed. Only the singles work, the ranges don't.
Question: Has the EA4500 resolved this issue and allow for either more lines (i.e. 20 customizable entries instead of 10), or, better, does it just have an [Add Entry] button to allow for additional rows to be created? In today's day and age, where one single device (such as an Xbox) can take four rows, a 10-row limit is pretty sparse. Comparing it to some competitors, for example the D-Link DIR-825 (aging, but still great) allows you to add as many as you want.
I realize "expensive" firewalls like SonicWall's have virtually unlimited customization, but I don't need many of the additional features and don't want to spend $350 on a "high-end" firewall to solve the problem of needing two more ports open.
I just reinstalled windows and am trying to restore my previous settings. I was wondering how to do that, specifically with the bookmarks.I originally saved my bookmarks with an export, and I have the saved file.I cannot seem to get my bookmarks back. I have tried all of the options.I am using the internet browser, google chrome.
View 2 Replies View RelatedIs there a way to transfer all the 'saved' wireless networks from my current laptop to my new one? I go to many different offices and have probably about 50 wireless networks 'stored' on my laptop. Everytime I go back to that office it just automatically connects. I would hate to have to try and find all these passwords again. Is there a way to transfer all this to my new laptop?
View 6 Replies View RelatedWhen I make changes to the config of my ASA 5505 and write mem (or use the ASDM to save running config to flash) the changes are not being saved.
Is this going to be a problem with the Flash Memory on the device?I have successfully saved config on this device in the past, which is why I am thinking it might be a problem with the flash memory.
I had a problem earlier today upgrading to a new N router. All PCs in the house connected wirelessly except my laptop which I got the message below.The settings saved on this computer for the network do not match the requirements of the network.
View 1 Replies View RelatedI can't seem to find and answer to this, but is it possible on a 2504 WLC to trigger a configuration backup when the configuration is saved like on Cisco routers and switches?
View 2 Replies View RelatedI have a 5520 runing 8.4 and I would like to activate a previosuly saved configuration without reloading the 5520.
View 3 Replies View Relatedi don't know how I have done this but I have managed to connect my partners laptop to my network list on my new Toshiba laptop (don't know if make or modal matters) this seemed to have appeared whilst uploading and fetching photo's with skydrive,how do I get him off my network list???
View 1 Replies View RelatedSometimes I need to login to server shared folder with different username and password than saved one in "manage network password" or "windows credentials" (windows 7). At that time, I have to delete the previous one in "managed network password", then open the shared folder with new username, again save the old once once it is done.Is there anyway I can just open with different usernames without deleting the saved one? Different users have different privileges in server. Similarly, how to delete temporarily network cached passwords without restarting? I tried net user * /delete but it doesn't work?
View 3 Replies View RelatedWe purchased a new monitor to the pc where the router is connected. Since then, my laptop does not connect to the internet. My network is on the list but it says "The settings saved on this computer for network do not match the requirements of the network" and the Connect button is not active.
View 1 Replies View RelatedNo matter what I do, whenever I enter the Web Interface for my E4200, the page comes up in Russian (at least I think it is russian!!)! I have changed the language to English (by trial and error discovered it was the first option at the top of the pull-down list) many times and yes, selected save at the bottom of the Setup page. I get the message back "Your settings have been successfully saved".But next time I go in, it is back to either Russian or sometimes some other wierd script, and I have to reselect English.
View 2 Replies View RelatedI have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
View 17 Replies View RelatedSince the EA4500 automatically updates via the Cisco Connect Software, does a copy of the firmware file get saved to the local computer?
View 1 Replies View RelatedI have this problem i can't open my ports on my D-link 524, i have opened about 6 ports so that my XBOX 360 works with a open nat, i have also set the DMZ to my xbox's IP which is static btw, my PC is also static. This is how i basically tested and it told me that it was not opened. I went into:
192.168.0.1 -> Advanced -> Virtual Servers ->
Enabled
Name: XBL1
Private IP: 192.168.0.100 ( because i was testing it on the computer - if it
were 360 it would be .141 )
Both UDP and TCP at port 3074
Schedule=Always
Apply -> Then restarts modem/router i waited for 2 minutes before turning them on again, i turned router on first because some guide told me to do that.
I did exactly what they did on portforwarding.com then i opened up portchecker and typed in 3074 and pressed check -> This port is NOT opened. What is wrong? This is how my net is set up.
Modem ZyXEL -> D-Link 524 -> D-Link DGS 1005D -> Computer/XBOX.
I can't get port forwarding to work, even when I turn off the Windows 7 firewall and AVG anti-virus software I'm running. I entered the IP address of my laptop (with a DHCP reservation) and UDP and TCP port numbers, with Schedule set to Always and Inbound Filter set to Allow All. That should be it, right? However, when I check the ports using PFPortChecker, both the UDP and TCP ports are blocked. I do have a Linksys wireless router daisy-chained to the D-Link router, but I'm not communicating on this computer through the Linksys router and the problem still occurs even when the other router is disconnected, so that doesn't appear to have anything to do with the problem. I just updated to the latest firmware (3.13NA).
View 11 Replies View RelatedI want to open MORE than the 24 ports that the router configuration allows (DIR-615 Hardware Version: C2 Firmware Version: 3.03RU)?
View 14 Replies View Relatedcant open the ports 2300 -2400 (udp, tcp)on router. What I do isthe following.
1. Open ports on router in port forwarding.
2. Add the triggers as well in APPLICATION RULES with the ports. Triggers are 47624 and 6073.
3. Try both Dis and Enable UPNP. Even try the DMZ enabled settings.
4. Disabling firewalls on Laptop and router. Try both ways on DMZ's(enable and disable) settings on router. Check everything.
Still when I check on websites about the ports and they are shown closed (NOT STEALTH). Router uses a firmware 4.0. I have a windows 7 64 bit system. I use wireless.
Note: All the steps are performed in a combinations manner to see if there is any possibility of opening ports.
i've tried plugging in various devices (computer & solar panel management device) into the ethernet ports to no avail. i just updated the firmware, reset the router, and still no luck. all of the lights work when i reset and the wifi works fine. do i need to do something in the settings to turn on the hard connection?
View 3 Replies View RelatedPorts are still closed after forwarding them dont know why am using TP-LINK WR740N.
View 3 Replies View Related1.) I don't have a wireless card in my PC, so I will be connecting wired to get WiFi via WAN and LAN ports, right? I have a Windows 7 32-bit desktop PC. We are working with a DSL modem residential line without phone line using a coaxial cable, and Ethernet cable from modem into the PC. provide step by step walk through instructions by connecting this D-link router to my modem and WiFi, and for me to use the WPA2 security?
2.) I have an iPhone 4 with Verizon. If I want to use my iPhone to get WiFi from the router, and turn off the Internet, and use WiFi only on my phone, how would this work?
I have been trying to block access to Steam and Left 4 Dead 2 on a specific computer, using the correct listed ports and using the port forwarding section of the router (setting the access to deny) however they seem to still be able to access both steam and L4D2 on their computer.how I can still block the access?
View 1 Replies View Related