I realized that when I connect dir825 on bridging mode to my current voip router provided by my ISP (dvg-n5402) ,shareport does not work as it seems to be using the default gateway to find the usb, which in this case default gateway goes to the gateway of my voip router. Is there any way that I can make shareport use the gateway of my dir825 instead?
View 5 RepliesIs there a client mode option for the DIR-655?I just got a nice cable modem/router from my ISP and I'd like to re-purpose my DIR-655.If I could turn a usb webcam, printer, or harddrive into wireless client, that would be cool. I would just rather re-purpose the device versus selling it.
View 2 Replies View RelatedRecently I bought a Windows 8 (64bits) computer, which is now part of my home network, but it has problems with Shareport. The other computers can be easily connected to a USB printer on my DIR-825 (HW B1) router, but the W8 computer refuses to completely install Shareport (both the CD version and the latest download v1.17). I also tried Shareport-Plus v4.11 (found on the DIR 835 page), which did install correctly, but was still unable to see the USB printer. What can be done? Can D-Link provide a new version of Shareport?
View 3 Replies View RelatedI have hardware version B1, firmware version 2.00NA and several computers (wired & wireless) with Vista & Win 7 x64 and a Brother HL1440 printer.When I print something it comes out scrambled, images missing or cut off, empty pages, etc. This same setup worked fine when it was directly into one computer, then shared on the network though windows sharing. The problem was that computer had to be running to print off the network. I got the dir655 since it had printer sharing but so far its not been of any luck.
View 5 Replies View Relatedhardware version D3, FW 4.10 and 4.11 same problem.
i tried with 4 wlan adapters: two of them support 802.11b/g, they always work find no matter which settings. the other two support 802.11b/g/n, as default "n" is enabled, so does DIR-615, both wlan adapters can be connected to DIR-615, they get their LAN-IP, but they can access neither DIR-615(no respone to ping) nor internet. but if i disable "n" mode either in the adapter or in DIR-615, everythin works fine, of course only with 54mbit max.
so what can i do to use the n mode?
I have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
I have disabled all antivirus and firewall services on my PC and I can't get Shareport icon to turn green and recognize my DIR-655 (Hardware Version A4, 1.21 firmware). I've uninstalled the Shareport software twice. I use AVAST (but all services are disabled).The router setting is set to "USB Network" with a 30 second time out. I'm running WinXP SP3, 802.11G only.
View 11 Replies View RelatedMy router is near my TV.I was hoping to connect a usb videocapture device to the usb port and connect with shareport to my pc to stream tv content.
View 2 Replies View Relatedsomething has changed, and now SharePort is back to its old ... Text prints OK, but photos only print parts then eject the page and print some more psycho garble on the next page....etc...I have done all the uninstall - reinstall drills.... same result.... Just don't understand why it WAS working for a while, and what changed to make it un-work now.... The software looks to be working, but the actual output is foobar....
View 5 Replies View Relatedim wondering if it still have issue on shareport. cause last time i updated my 655 to 2.07 it has issue with the shareport.
View 1 Replies View RelatedI plugged the printer into the DIR-655 and downloaded Shareport. Nothing. HP Laserjet 1320
[URL]
If Shareport can not be used, which one of the programs on that page might work?
I have installed a d-link router dir-825. I have already connect a printer with shareport and it's working very well. We have also a laptop wireless connected; The problem is that after installing shareport on the laptop I get the message in shareport: no device connected;
View 14 Replies View RelatedI have a 1242 Access Point as root and a 871W Router as a non-root bridge (Diagram attached). I have a laptop connected to Fa 0 of the 871W router.
* I am able to ping from the AP to the Router and vice versa
* I am also able to ping from the router to the laptop and vice versa
* But I am not able to ping from the laptop to the AP
All bridging commands seem to be fine. Even tried adding route commands, but none seem to work.Please find the configuration below:
Configuration on Root AP:
hostname ap
!
enable secret 5 XX
!
[Code]....
Shareport recognizes the printer only after resetting the DIR-825 router. I don't know if this is a Shareport issue or an issue with the DIR-825 disabling the USB port.This happens after there is no PC connected to the router for a number of hours such as overnight. I have 1 laptop and 1 desktop running Win 7 64-bit and 1 laptop running Win 7 32-bit. The desktop is connected directly to the router and the laptops connect via wifi. All PCs work perfectly when the DIR-825 is reset.This isn't a big issue but it's extremely annoying and shouldn't happen. I use a Cisco WAG320 in my office that has similar USB functionality and this never happens.
D-Link Router: DIR-825
FW Version: 1.13NA
Operating System: Win 7 32 and 64 bit
SharePort Version: 3.1.0 R1 (SXUPTP Driver : 3.4.6.0)
Is it possible in the near future?
View 5 Replies View RelatedFirmware 2.07NA for version B1 units contains two bugs:
1 - An underscore in the Device Name causes a cryptic "37" error to appear when attempting to save any changes to the network settings. Version 2.03 allowed the underscore character. Other invalid characters, such as a "-", generate a more meaningful "Device name given is invalid" message.
Removing any underscores eliminates the error and allows settings to be saved.
2 - The upgrade breaks SharePort communications; the SharePort client utility cannot see the USB port on the device after upgrading from 2.03 to 2.07. This occurs with the latest 3.1.0 R 1 Utility (SXUPTP Driver: 3.4.6.0).
Downgrading back to 2.03 is a workaround.
I setup sharePort today and attached an external 1 TB hard drive. Seems that All my internet connections are slow now. I have a seperate PC that I use VPN to connect to work with and suddenly its very slow. My wife said her laptop suddenly slowed down too. The PC that I installed SharePort software seems slow too. Is/can SharePort be dragging down the router? I turned off the external HD and it's still slow.
View 14 Replies View RelatedRegion : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.107 Build 121123 Rel.31456n
ISP : COMCAST
This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.
I have an HP OfficeJet J4500 that works fine with shareport on my Win7 x64 computer. the XP and Win2000 ones both have the same "partial page then lockup" problem. when this happens, the only way to disconnect shareport is to reboot the router. It shows connected to the same computer even if I reboot that computer. I started with V1?? from the install disk then tried 3 and finally 4 with no improvement. I have read several posts about this or similar problems. This is the primary reason I switched routers and bought the D-Link DIR-655, for the print server feature...
View 3 Replies View RelatedIs there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies View RelatedI have some network experience but not a lot so here is my problem.I have a zyxel q1000z from qwest that i want to bridge to my dir 655.I go through the settings to put their router/modem to bridge mode. This units default ip is the same as tslinkink, 192.168.0.1 so i change the d-link to 192.168.0.2. I then go into the D-link and enter my isp's pppoe settings and password. I reboot when i am done but can't connect to the internet.It shows connected but that's it. I want to use the d-link as the only router as the zyxel has very few settings and has slowed down my netflix.
View 2 Replies View RelatedI rencently moved house and after 10 years on cable at 19400 Mbps I'm now on ADSL 1 at 1500 Mbps. I have a DIR-655 which I want to keep, and I've purchased a DSL-526B to connect me to the Internet. (I was originally told ADSL 2+ was available, but then I was told I am on a pair gain system and only ADSL was available.
Before I set up bridging I changed my password on thr DSL-526b now I can't log into the device. Is there a way to fix this without a factory reset?
The DIR-655 has all my DHCP reservations, ACLs, Web filtering, MAC address filters, QoS and schedules. The DSL526B has only a small subset of the features of the DIR-655 so I want to set things up to use the DIR-655 as the controlling device and the DSL-526B as nothing more than a modem.
Once I'm back into the DSL modem, I can set it to bridge mode. My DIR-655 manual appears to say nothing about bridging. So...
(1). Do I only have to enable bridging on the DSL modem?
(2). My ISP runs PPPoE. I note that both devices support this. I assume I leave the PPPoE settings (username, password etc), in the DSL modem, and do not put the details into the DIR-655.
(3). I then plug ethernet cable from DSL-526b to Intenet port of DIR-655
(4). I use 192.168.1.250 as the DSL-526B's address. I used to use the same address for the DIR-655. I assume I need to give the DIR-655 a new address (Eg 192.168.1.251)?
(5). DO I still point the PCs at the DSl-526B for the gateway and DNS or do I point them to the DIR-655?
Today I want to build a wireless bridge using AIR-AP1131AG (running WLC) and TP-LINK wireless router. The result is failed. May I know AIR-AP1131AG is support bridging the wireless connection with other vendor's access point or not?
In the TP-Link I already match its SSID, Channel and put the mac-address of the AIR-AP1131AG. In the WLC I already see too TP-LINK mac-address is already become a client.
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
Region : Others
I have Enable WDS Bridging and run Survey which detect the other SSID to be joined with the correct MAC address.I had filled the password of my second THOMSON v 585 V7 with the correct Auth Type both routers broadcast on channel 11.But my TP-Link 2543ND cannot made it work.I also disable DHCP and changed my LAN ip to 192.168.1.2 and can access it over my lan.
The setup:
(1) E3000 as root router - IP: 192.168.1.1 - DHCP Server: Enabled - Start IP Add: 192.168.1.100
(2) TL-WR841N as bridge - IP:192.168.1.2 - DHCP Server: Disabled - WDS Enabled
The problem:I bridged (2) Wirelessly to (1).when i'm connected to (1) there seem to be no problem at all, the internet is working just fine and i can even ping & connect (2), i guess that means the bridging is working.But when im connected to (2), I get a 'limited connection' & I can't connect the internet. I also can't ping & connect to (2).The IP assigned for the computer that is connected to (2) Wirelessly is not matching the DHCP confg. (169.254.228.216).I have reason to belive that the problem is somehow from a wrong configuration with the LinkSys router but i dont know what it could be. i started from scratch, reseting the two routers over and over again while trying different configurations but with no luck.
i got a Dir-655 router and Dell 1501 wireless -N mini PCI card (802.11 bgn compliant). Router was set to mix mode but my desktop Dell XP8300 can connect only till G mode.
1) I search on web and some said that i need to set my router to N mode only for my desktop to connect to N mode. IS THIS SOLUTION CORRECT??
2) Another issue was my sis got other old brand latop which can only connect to B mode, if i set to N mode only, she won't be able to connect it right?
internet only work in safe mode?
View 1 Replies View RelatedJason9 i'm having the exact same problem as above, don't mean to hijack but I'm using talktalk isp, I have AVG 9.0 and have a static IP and forwarded the required port on the router.
View 19 Replies View RelatedSeems like there those saying they have gotten there DIR-655 and XBOX 360 Wireless N Adpater to work in 802.11n mode. The adapter will only connect in 802.11g mode (and yes I have the correct adapter). I have set the settings to following
802.11 Mode: Mixed 802.11n and 802.11g
Wireless Channel 2.462 ghz - Ch 11
Transmission Rate Best
Channel Width 20/40
WPA-Personal
WPA2 Only
Cipher Type: AES
Does this router really work with XBOX 360 Wirelss N Adapater. If so, how has others got this to work.
I have an ADSL Modem WAG200G Annex A, with latest firmware. I recently purchased a Linksys E2000 to upgrade my wireless to N, plus to get 4 gigabit Ethernet Ports for my NAS.
The problem is, I set WAG200G to "Bridge mode only", and from within E2000, I provided PPPoE credentials (user name and password), it does not work, no Internet connection!
Normally, with the WAG200G, PPPoE credential is set as followings (and it works)
Type: PPPoE Multiplexing: LLC Virtual Circuit: "0" for VPI (0~255) and "33" for VCI (0~65535) "Keep Alive" option
on E2000 Router, PPPoE does not have the above option for me to select. Only User Name and Password field
I have a ASA 5510 that is connected to my ISP and the inside interface that is connected to my router. I have a /30 and need to determine if the configuration of x.x.x.121/30 which is my ISP and also the BVI address on the ASA. The inside router address is x.x.x.122/30 same subnet as my ISP will allow me to pass traffic. Management interface works using a different ip address but not able to get the traffic to pass traffic out to the internet thru the ASA
ISP-------->ASA-------->Router
Bottom Line is that I only have one usable address that is being used by the router and the ISP and ASA are using the other. Will this work?
I'am using router E1500 in a bridge mode (aka WiFi access point N standart). I want have two chanel transmitions, but i see only one chanel. In a specification write 2T3R (up to 300 Mbps).
View 6 Replies View RelatedI'm trying to configure my WAG200G to work in bridge mode so that it can transfer my external IP address to my ISA server.My network map is very simple,Internet -- WAG200G -- ISA Server -- LANCan
View 7 Replies View Related