We have to configure our firewall cisco Asa 505 (ASA Version 8.3(1)) in order to establish a ipsec vpn between our office site and another external site. Vpn has been established successfully between our ip site 172.16.69.24 and other vpn ip site 172.16.23.23.Our server (192.168.100.25) behind firewall cisco (sk lan 192.168.100.254) manages to ping server 172.16.23.23 on other site through a static route add on windows so server (route add 172.16.23.0 MAK 255.255.255.0 192.168.100.254).On the other site, server with ip 172.16.23.23 doesn't ping our vpn ip site (172.16.69.24) which has to be natted to our server 192.168.100.25.
I am having an issue with internal and external clients. When we have the nat ip configured on the controller we cannot connect internal ap's at all. When we take the nat ip out it works fine. We are on code 7.0.220. I have tried the following command <config network ap-discovery nat-ip-only disable> and it did nothing.
I was just wondering how to connect 3 laptops to 1 printer in my office?We don’t have a server and all laptop contacted to internet wireless through a router next door. (I don’t have access to that router)I was thinking to get a hub and then connect it to the Ethernet cable back of the printer and then connect it to each laptop?
I would like to connect my three pcs together so that they can all make use of the printers, scanners, internet etc in my office space. i also need to be able to access this lot from a remote laptop so that i can continue to work from home. i would like to store all my data in one place that was easily accessible from every PC and my laptop.
I have a Dell XPS L321X, ultrabook, which can connect to wifi except a specific office wifi, say TPR. The interesting thing is I can connect to this TPR wifi when nobody is in office, I thought it might be an IP conflict. So I tried to assign a static IP address, but it doesn't work. I have updated the wifi adapters two days ago.I tried few things like IPCONFIG /RELEASE, IPCONFIG /RENEW, but nothing works. The security type of all the wifi in my office are WPA-PSK and they all have good strength. We use sharepoint services for our daily office work, which can be accessed only using a TPR wifi. It's frustrating that I cannot connect to it.
i am having problem adding the officejet printer that was uninstalled because it was not working. after three days of online support from HP and Lynksys, I am about to buy a new printer. Can't add printer wirelessly or wired.
I have a Any Connect setup and able to VPN into my office.i bought a ASA5505-SW-UL that is unlimited user (UL) software license but now the vendor tells me that: From the ASA you can saw the unlimited license is for inside hosts, instead VPN client's, by default, ASA 5505 included only 2 VPN client's and can supported up to 25 VPN client's, your license look only default 2 VPN client's. If need more VPN client's connect, you have to purchase the additional VPN client's license. I am just wondering his statement TRUE/FALSE, because i thought ASA5505-SW-UL means unlimited license
I have my laptop. I need to use my broadband connection at my home. Also I need to use my laptop with wifi at my office. We do not have any dhcp servr at office. What I am doing now is changing ip configuration at office every day manually.
I have a group of five computers at one end of my home office and another group of four computers across the same room. All are hardwired on the same internal network. These cannot be consolidate or moved into one corner or closet. There just is not the space and it's just physically not possible.There is one Internet router as provided by the local cable company. I have this connected to a LinkSys WRT54G2 broadband router. A Netgear DS108 8-port hub is connected the LinkSys. All computers either connect to the Netgear hub or to the LinkSys router. As of now, the WiFi from the LinkSys router is only ever used by my cell phone while at home.
This set up is annoying. At first I did not mind, but there are cables on the floor that I have to step over. These CAT5 cables connect one set of computers to the LinkSys or Netgear. I have to watch where visitors are walking or stepping to assure they don't trip.How can I keep these computers on the same network and eliminate just those cables crossing the floor of my home office?Should I use WiFi NICs? Would this overwhelm the WiFi on the LinkSys?
I have got two 1841 and one 881 cisco router. I can keep any one of this router at HO and remaining at branch office. I have got a static internet IP at HO but dynamic IP at branch office. I want to setup a VPN to connect to HO from branch office through router. The branch connects through a private IP for internet purpose. Which VPN is the most secure and best for this purpose.
I'm trying to connect to my home laptop from work. The home laptop is connected to DIR-655 router. I set up the internal and external ports to 3389 using both TCP and UDP protocols with the Application as "Remote Desktop". From my work PC I enter the external IP with :3389 and it fails to connect. I have also tried accessing internally which is failing too. All computers are running Windows 7 Home Premium Remote Access is enable on all.
I have been told to connect our branch offices over outdoor point-to-point wireless CPE. The wireless brand is Orthogon. The Main office got cisco 4507 L3 switch where all building switches terminate. DHCP,DNS and all application are hosted in main office. The branch office got ONE 24 port POE Switch cisco 2960 where all users will be connected, On Port 0/24 of 2960 switch at branch will terminate the outdoor Wireless and other end will be terminated on 4/15 of 4507 at main office? what command I need at both interface where Wireless is terminated.when we connect floor switches to 4507 we got these commands on access switches
i can can ping my host externally from another ip however i have left my house without port forwarding to my pc is there a way to connect to my pc via something like this command "xxxx.dyndns-home.com:192.168.1.100" i have tried this and does not work as it does not like the ":"truth be told my real goal is to ultimately be able to look at my webcam as it is pointed at a homebrewing project which i need to see. this is what i want to work on setting up while in rdp?
From our Exchange server, I am completely unable to communicate with one of our partner's mail server. I cannot ping it by either the host name or IP address. Trace route times out at the final hop. The firewall is disabled, and antivirus (ESET) is temporarily disabled. I cannot access the IP through the web browser either, everything times out.However, every other computer on our network can connect fine. I haven't seen any other problems with any other IP addresses, it seems to be only this one that I can't connect to, and only from our Exchange server. All computers are going through the same gateway, using the same internet connection, and using the same DNS servers.The computer that I'm having the problem on is a static IP. All settings look correct, and match another server that I can access the IP from.I've checked the hosts file for anything, and it is in it's default state.
I have a DIR-825 Rev. B1 wireless router running FW ver.NA2.0.7. I want to connect a Seagate 4Tb external HDD with USB 3.0 into the USB 2.0 port on the router to use the hdd as a NAS and run backups of the data files on the computers of my home network. The computers are running Windows 7 - 64bit. Plugging the hdd into the USB port on the computer lets it be recognized and ensured that Windows 7 had the most current drivers. When I plug the external hdd into the USB 2.0 port on the router and then plugging in the hdd and resetting the router, I still cannot get the computer to find the hdd on the network.
I've been having a problem with my wifi for a month or so. I used to connect well to my wifi, but then one day my laptop just can't connect to it anymore. It says "windows was unable to connect to" or something similar to that.But what's strange is, I have an external wifi adapter (Tenda 802.11n, it looks like an USB flash drive). I use this adapter to connect to Wifi with the very same password, and it can connect perfectly. Signal strength is around the same level.I tried using windows troubleshooter, didn't work. I borrowed my friend's laptop (which is very modern, and have windows 7 - mine has windows XP), but the same problem exists: the laptop can't connect, but the adapter can.I also tried to export the wifi settings to an USB flash drive (using windows 7's function), and installed it on the laptops. Didn't work. [code]
I'm trying to set up a personal ssh server on Lubuntu 13.04, but I've been having a few problems.
So far i've accomplished this:
I can connect locally, through my internal IP address, I can ping myself through my external IP address through an external internet source(Mobile phone hotspot + Different computer)I have a free dynDNS running, so that I don't have to type my external IP address.It works (if i connect to that IP locally, it forwards to my router)I set up port forwarding in my router, temporarily disabled my personal and the router's firewall too.
The problem I have is that I cannot connect through ssh from a different computer outside my network: The usual response that I get is "Error.. [etc] No route to Host".
I tried using the 'canyouseeme.org' service, and the response is the same.
I use an Internet Service Provider called iiNet, and apparently they have some per-account port blocking features, which I have also disabled from their site.I am running short on resources. DMZ does not work either, default port (22) does not work, custom port does not work either (9222, 9512 or 12222).
So I'm guessing it's either a router fault, or a fault on the ISP's customer-level firewall.
I'm connected using a Edimax 7811-nu adapter (Default driver doesn't work, had to install a fixed one)
I'm using a BoBlite Router and the firmware version is BoBLite1500.
I have a Seagate 1TB USB External Hard Drive that I want to share on my wireless home network, and I'm having difficulty finding a cheap, reliable solution. I would also, ideally, like to connect a USB printer for similar sharing.I have two XP PC's on the network, and will probably be getting a Windows 7 machine.The router is the generic one supplied by my ISP.
1. Connect both hard drive and printer to always-on PC that shares with Windows.This would work but I'm not keen on the 'always on'
2. Use a Pogoplug to connect the hard drive and printer to the router Again, a good solution and always-on, but a little pricey - ?60-100?
I have a Linksys WAG 120 N wireless router with an internal arial. I want to strengthen the signal to my laptop 2 rooms away as it keeps dropping out. Is it possible to change WAGGING from internal to external antenna to increase range/performance?
I want to connect to the Internet small office where docsis (internet over tv cable) is used as WAN.For similar tasks but other WANs (adsl, dial-up) I used 800 series. But now I can't find anything in this series to solve my issue. There is 815 but it has no wi-fi.
I can use cable modem that my ISP gave to me: this modem acts as bridge so I can use router with FE-based WAN but it is better to have one device instead of two.
Just updated to the 1.01 firmware on my DIR-815 and now it doesn't handle loopbacks anymore.
For instance, I have a dyndns address of ericnewton76.dyndns.org. This points to my router. Works fine if you're NOT within the router's internal network, ie, outside hosts can get in just fine (try it... http:// , you'll see an IIS7 welcome screen)
However, when INSIDE the network, the requests don't get connected properly, and they used to... ie, I work with code, so my svn repo is at ericnewton76.dyndns.org/svn but inside my network it doesn't connect properly anymore (whereas it used to before firmware update)
So now I wish I could back-peddle to 1.0 firmware.
I have a Linksys WRT350N which I am trying to use an app on my iPhone to connect to my server using the public/external IP of my cable modem. I have the necessary ports opened and also tried adding the server to the DMZ but no matter what I can not get the app to connect to my server via my external IP when I am on my WiFi. I can connect without any problems if I use the NATed IP on the server when my phone is connected to the WiFi. It also works fine connecting to the external IP if I am on any other WiFi or the cellular network (which shows ports are forwarded correctly). I just can't connect to the server when I use the external IP and I am on my WiFi network. This is annoying as I need to keep changing the app's settings back and forth between the external and internal IP whenever I am home or away. I am left thinking this is some kind of issue with the WRT350N not allowing local internal traffic to reach the external IP. Any way to resolve this, maybe by entering a static route?
I have a hosted web server that has a website on it that needs to connect back to a database within our internal network. We have a Cisco WRVS4400N Wireless Router with 2 VLANS. VLAN 1 goes to a Watchguard Firebox which is connected to our internal network. VLAN 2 goues to our classroom network.
Our database is on VLAN 1. I have opened port 1433 on the Watchguard to allow SQL traffic from our Web Server. I can telnet from my workstation on VLAN 1 to the Web Server over port 1433, so I know the Web Server is not blocking anything. When I try to telnet from the Web Server to our Public IP address over port 1433, it fails.
I believe I have the firewall on the Cisco WRVS4400N off, so it shouldn't be blocking any traffic, but for the life of me I can't get this to work. I have been working on this for two days, and I NEED it to work. This was working up until last week, then it quit working. I am the only person making changes to our network, and there were no changes made during that time.
I just bought and installed a new NVIDIA graphics card to replace my old one.After installing it, I now can't connect to internet. My modem and Router work fine, but my computer cannot find its IP address. I checked (C: prompt) and found the dreaded (169.) showing my computer can't connect with it's IP and I have tried everything to fix it?