Home Network :: Unable To Establish Remote Connection To Second Router?
Jul 15, 2012
I have a sky router (Netgear DG834GT), which i have connected a secound router to which is a D link DIR-615 (with DD wrt firmware D4).I can get access to the sky router remotely without any issues even when changing the port number. its the Dlink router i cannot get access to remotely (within the network i can by typing in the dlink's ip address and works). Main router Sky router IP is 192.168.0.1 - Currently the port number is 8081.Secondary router Dlink IP is 192.168.0.2 (Static ip) - currently the port number is 8080.I have tried to configure the ports but it just dont want to open. Ive tried to open the ports on main netgear and tried all the option my dlink for port forwarding. i must be missing something fundametal here.
We have two sites, Site-A with a ASA 5520 (Remote Access IPSEC VPN server) at one end and a new ASA 5515-X at Site-B. Users at Site-B are unable to establish a VPN connection to Site-A via Cisco VPN client from behind the new ASA 5515-X. They see the following error:
"Secure VPN Connection terminated locally by the client. Reason 412: The remote peer is no longer responding.
They are able to access the same from home or elsewhere so I believe there is nothing wrong with Site-A ASA vpn config which we have been using for a while now. The new 5515-X (version 8.6) has a very basic config with all outbound traffic allowed. I'm pasting the config below. Do I need to enable/allow anything for it to work?
CISCOASA# sh run: Saved:ASA Version 8.4(3)!hostname CISCOASAenable password xxxxxxxxxxxx encryptedpasswd xxxxxxxxxxxxxx encryptednames!interface Ethernet0/0 nameif outside security-level 0 ip address x.x.x.x 255.255.255.248!interface Ethernet0/1 nameif backup security-level 0 ip address
I need to get the internet from my uncle and aunt's house to my grandma's house next door. I don't know exact feet or anything like that yet but I will get it measured off. My grandma's kids got her a laptop for Christmas but she doesn't have the internet or would be wanting to spend money on it a month since she already says she will not be able to use the computer, but I said we would just somehow get the internet from next door. I don't know off the top of my head but my aunts computer is an older Dell, early P4 computer with xp on it. It's slow but it does work so that is the computer. The router is some sort of D-link with one antenna on it and I'm pretty sure it's probably a G-router(2.4ghz) and not a N-router, but can get that info later too! They currently use Time Warner Cable Roadrunner Turbo for their internet. Both places are well built brick houses and at least 200-300 feet apart. I checked yesterday and the computer was able to pick up the signal in my grandma's house on the end that was closest to my aunts house. It was showing 2 bars but it wasn't extremely fast and that room had a bigger window in it probably allowing some of the signal in? If you moved from that point of the house though and tried to go to the other end, the signal was lost. The router in my aunt's house is one room away from the end of the house that is closest to my grandma's so it could be moved closer but I don't think that will fix the signal enough to do what I need it to do.
Trying to establish a wireless connection from WD TV Live Plus unit to Westell 327W router using an AirLink 150 adapter. The media player sees my network and seems to have a good signal, but keeps telling me "limited or no connectivity." The media player (with adapter) is about 20 feet from the router with direct line-of-sight.Also, 3 other Wi-Fi devices having no problem connecting anywhere in the house.Power down/power up, move adapter to alternate USB port, re-try connection multiple times.
We have ASA5510 with version 7.x and asdm 5.X, i upgraded it to 8.3 and asdm 6.2, and i got vpn peers 250 and 2 ssl.when i try to connect through client software , i can see in the logs UDP 500 port is created as shown below.Mar 31 2011 23:54:40 302015 94.97.180.0 57013 x.x.x.x 500 Built inbound UDP connection 56694 for outside:94.97.180.0/57013 (94.97.180.0/57013) to identity:x.x.x.x/500 (x.x.x.x/500) no other things are going on , and i get error as shown below.
Secure VPN Connection terminated Locally by the client Reason 412: Remote peer is no longer Responding Connection terminated on.
i am suspecting it is VPN-3DES-AES activation key issue.when i go to Remote Access VPN ---Advanced---SSL Seetings--From Left Encryption Panel Available Algorithems i have DES-SHA1 when i try to drag it tto Right panel of Active algorithems it gives me error *** below [ERROR] sl encryption rc4-sha1 des-sha1 The 3DES/AES algorithms require a VPN-3DES-AES activation key and currently in right panel of Active Algorithms i have only RC4-SHA1,
I have to unplug/replug my router powercord connection every time i want to use my laptop to access the internet. i have reinstalled the software disc that came with my router. i have have comcast check my modem-
Purchased E2500 1 week ago. I do not have a problem communicating with the router itself (either hard wired or wireless) but I have been unable to establish a usable internet connection from the router.I live in building that is wired by Restech Services - Ethernet jack in wall - no modem. Connection works just fine if I bypass router and connect directly to PC (windows XP SP3 desktop or windows 7 laptop.),Very difficult to establish any internet connection at all. I have to renew IP address many times or go through re-boot sequence multiple times. Once I get a connection it is unusable. If I attempt to ping a URL (either from PC or from router admin page) it is unable to resolve host. If I ping an IP directly (either from PC or router administrator page) I typically get 60 to 80% packet loss. As noted, if I bypass router and make internet connection directly to PC - no problems - no packet loss.Used Cisco Connect software to set up. On advice of ISP changed MTU from 1500 to 1300. Also registered MAC id with ISP and changed from cloning PC MAC to using the router MAC. Downloaded and installed latest firmware version. Did factory reset and re-configured the whole thing. Double checked and swapped wiring.
i am trying to establish a VPN connection between two remote offices.In the home side I have Cisco 1811W and on the far side CiscoSRP541.
What is the best solution to build a site-to-site VPN between those two locations. I originally thought to configure a GRE tunnel on the routers, but faced some issues with that.
i have a new smc router and my local ip address and remote ip addresses are very similar. The remote ip address is updating my dns server but i am unable to ping it. Its something like 122.61.xxx.1 ?
I have WAG120N and I want to use ssh tunneling to browse the net.In windows, I have to use a software like putty or xShell to establish a ssh connection to remote server.It works perfectly and I don't have any problem with it.The problem occurs when I want to use this ssh account in linux.At first,connection established without any problem or error.After 2-3 minutes it seems ssh dies and no data transmitted through ssh tunnel.I tried this with Symphony ADSL modem(Wired only) and I have no problem with it.I want to know if there's any specific problem or configuration for WAG120N to solve this problem?I like this modem/router and I don't want to sell it and buy any other modem/ router.I have to mention that usually I use wired connections to WAG120N,but at some cases I need to use its wireless features.
I have a RVS4000 with client VPNs setup and have created all 5 users......trouble I run into is that when one of the users attempts to connect to the VPN from a second device (ie the sixth device to connect to the VPN), the connection does not establish....cannot ping remote server (using QuickVPN). In looking at the logs, the device that isn't working is getting a different IP (172.16 vs 192.168). I know I'm limited to 5 users, but am I limited to 5 devices as well?
i want to setup a remote desktop connection for 3 computers on the same network to connect to remotely. Originally i was going to port forward the original windows RDP port and run the windows rdp service but learnt that XP Home Edition doesn't support this feature. I want to be able to log onto these computers at any time remotely with the need of accessing the computer before i connect.
I have a CISCO Linksys WRT610N router on my home network which consists of the following 4 computers; Windows Small Business Server 2003, one Windows 7 Ultimate and two Windows XP Professional. How to configure a VPN on the WRT610N router that would allow me to access all of the computers on my home network over the Internet using the "Remote Desktop Connection" component.
Device asa 5550 - But can a Client establish a SSL VPN to remote network and devices on the remote network access local network printers? so you got one client one network A that creates a SSL VPN to network B , can network B be configured so that automatic job come across the same ssl vpn to a Different IP?
I have a high speed wireless DSL router from my ISP (Telus). I use one port off the router to connect directly to my desktop computer. Another port is connected to a switch to which ethernet cables to three other rooms are connected. My problem is that when I connect my Bell PVR (9242) to the 'switched' ethernet cable, I'm apparently not able to get a dynamic ip address, which the Bell unit requires, and can't connect to the network.can I connect another router, in place of the switch, to deliver dynamic IP addresses to whatever I connect to the ports in the other rooms in my house?
I am unable to set router's (RT-N56U) IP adress to default one (192.168.1.1), or any other in subnet 1. It always popum message to me which says "IP adress 192.168.1.1 is not a valid adress". Also when I restart device it automaticaly sets its IP to 192.168.2.1. I have static IP which is translated to IP in subnet 1 so I need this working. The router is in "Wireless router mode (Default)"
I recently installed a new router - WRTP54G . I used to have our 2 machines on a home network. However, that is all gone now. When I open My Network Places on my pc, nothing at all appears. On the other pc only the shared folders on that pc appears. I've tried running the network wizard several times and to no avail. I've checked the permissions and everything else I can think of, but it still doesn't work. I believe it is probably something simple to fix, like checking the right box, but I haven't found it yet. Both machines are running XP Home and I have an external drive attached to my pc. Everything worked fine till the installation of this new router. Should I just create a new network? Would that just be easier? One more thing, I got the error that says Home is not accessible. You might not have permission to use this network resource. Contact admin of this server to find out if you have access permission. The network path was not found. Of course, I am the admin.
After trying most things and spending money like water, I still cannot get our home network to be adequate and I am out of options - Tried using two 100MBit/s Netgear routers "bouncing" signal to each other (Wireless Repeating Function). Not ideal as security is small and speed was slow (<10MBit/s) but at least it worked. However these routers had to get pensioned off when we put gigabit ethernet in the office - and the Netgear replacements (a) still have the security limitations with wireless repeating, (b) anyway see to do a worse job of repeating. Tried buying Netgear directional high-gain antennas and directing the signal point to point to a second router - didn't work at all. Tried Powerline (this was in 2008). It sort-of worked but was unreliable and dog slow. I think this is probably not worked by the fact that this building is OLD, most of the wiring is OLD, and anyway the electrical path would take the signal from the 4th floor, down some very old wiring to the ground floor, across a very old switchboard, and back up to the second floor... it's not quite the same as a modern house with modern wiring. Most recently tried using Netgear's Wireless Network Extender. Again, it sort of works, but it's NOT fast at all. In addition there are times when some of our computers using the extension segment of the network are unable to connect - they can still see 3-4 bars of signal, but they cannot get on the network. Appears to be an issue relating to gateway, or DNS, not sure. But I would say about 1 day in 3, when I come home, my wife tells me that the "internet is off".
I am unable to connect my Ipad3 to my home network (WRT160N router). It has been working for the last 8 months, and stopped working after I installed Direct TV App on Ipad..It detects the network, but not accepts the PW.... I have multiple wireless devicess connected to my network without any problems..The funny thing is that my neighbor brings his ipad to my house and he is able to connect..My ipad connects to any other network...just not my home network.. I contacted Apple who spend hours with me on the phone and suggested doing a full reset on the ipad, but still did not solve the problem..I called and already paid for linksys support ($62.95) who spend hours with me on the phone, but suggesting: "maybe you need to buy another router"...REALLY!!!! Again, I have 3 Smart TVs, Xbox360, and Wii, that are connected to the network just fine .even my neibor comes with his Ipad3 and connects to my network just fine......and I can connect with my ipad to any other network without any problems... BTW, I have already removed the DirectTV app from the ipad....but I still cannot connect to my network..
I am facing problem when trying to establish VPN connection between ASA and 1841 router. Peer comes up but traffic is encrypt and decrypt. when assign route (ip route 192.168.x.0 255.255.255.0 fa0/0) to remote local subnet there is a traffic but one reply and one drop
ping from 192.168.y.62 ------------------------------------------------- Reply from 192.168.x.55: bytes=32 time=493ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=633ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=375ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=528ms TTL=127Request timed out.
I'll try and keep this brief, we were having problems with our netgear router (DGN1000) mainly with connection when online gaming with PS3, generally poor connection - so purchased a TP-Link router (TD-W8960N). We could usually access the netgear wirelessly on our laptops Dell and Acer Aspire 4820T (both Windows 7) without any problems and were still doing so last night. However hubby attempted to install the new router last night and all seemed to go fine but after installing we couldn't connect to the wireless network through laptops, iphone ps3 etc - even though we could see the network with excellent strength, after hours of trying called TP-Link they went through everything they could think of and still no joy. Gave up in the end and went to reinstall the netgear Router and now we have the same problem with this router, even though earlier in the night it wasn't a problem - we deleted the previous networks so there was nothing stored in memory & tried everything we can think of (although neither of us are brilliant with IT we do usually get by).We even set up an unsecured wireless network (on both routers) and still couldn't connect?
I need to connect my home pc to my office LAN, is there a way of connecting to the LAN remotely as if the pc was locally joined to the network? I don't want to connect to a specific pc just join the network itself. When I logged into the router management I thought I would be able to just specify a remote IP address that would be allowed to connect to the LAN as if it were local but there is no obvious way of doing that. The router is an SMC.
I've got a decent setup (Vista, 6GB RAM) that I use for web browsing, browser games, and the occasional MMO. My wife has something that works for her for browsing / browser games (Win7, 2GB RAM). Naturally, the kids are always on my machine, and whoever comes second is fine with Mom's. BUT, sometimes that ol' butthead Daddy wants to use his own computer! No problem - Junior got a netbook for Christmas. OH, but... it's not what he's used to... actually, it's slow enough in comparison (Win7, 1G RAM) that he gets frustrated and wanders off[CODE]
I have Nas storage AirNas 350 how ro setup my network to have remote access to NAS ftp ?i have TP-LINK TL-R480T+ with two wan ports with two modems (Cabble and ADSL 2+ both with dynamic IP) also i registered on www.no-ip.com I success to go direct to ADSL modem with no-ip service but i not need that i need to access to NAS storage.Nas ftp work perfect in local network but i need remote access over tha internet. How to setup that?
How to use my iPhone 5 using 3G or LTE to connect to my home wifi network so I can control things like my airconditioner (using the supplied app) which is also connected to the home wifi network?I have a WHS a Windows 8 machine and an XP Pro machine. I am using a Linksys WAG320N Router/Modem.
i have a wireless adapter connected to a different wireless network. now the issues is i have my own router which i want use for my ps3 and phone to access my files from my pc but every time i connect my router, it switches from my wireless to LAN by default hence no internet connection.i want to be able to use my wireless connection for internet
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
5 - Remote sites (no static IP there) 3 - Remote users (comercial) 1 - Central building (using static ip address)
Is it possible to establish a permanent vpn tunnel between each one of my remote sites to the main building, even if I have no static IP address in the remote sites?
Do you think that RV180 is the best choice to mannage vpn connection between remote sites and the central building securely and faster?
I'm having an issue with my laptop. Although, from my provider, it should be possible to establish a connection at 25'000 kbit/s (download), max speed is at about 800 kbit/s. I'm only about 20 feet away from where the router is located and I don't use any phones (except for a cell phone). I read on this board, that I might have to change the wireless settings on the router and change the radio band but didn't manage to do so. I'm using Mac osx and a wireless connection.
I am trying to configure site to site vpn between Cisco ASA and Cisco router 3825, I need to establish the vpn connection with an interface that has security level of 90.I followed the procedure shown in the following link: URL.
for example, there are 3 sites, A, B and C. A and B are 1.5 km apart and both are separate LAN(mixture of wireless and wired). C is 35 km apart from A and B. I have to connect A, B and C so that they can communicate with each other. Security is required.
I Got a new ADSL connection,They provided a ADSL Modem. To connect tot he ADSl i have to enter the username/password in the PC....in this case how can i make this ADSL connection to wireless? coz Me and my friend want to use the same connection.
i want to set up a vpn connection to my home network. i see that the e2000 supports ipsec, but does not provide a client. what client can i use to establish a connection?
