Linksys Access Point :: E4200 Discover New IP Address Of Reconfigured Router

Feb 14, 2013

I have changed from a DSL internet service to a Comcast cable system.   I have setup my E4200v1 router as an Access Point, to extend coverage in my building.  It works fine, but I can no longer log on to  the unit using its'  IP address 192.168.1.1.  The browser returns the message "Internet Explorer cannot display the webpage."   If I want to tweak the settings the only thing I can think to do is to push the reset plug, back to factory settings and go through the whole process.   Is there a way to discover the new IP address of the reconfigured router?  I left the default address as it was when I made the changes to AP status. 

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: Turning An E4200 Into Access Point?

Jan 22, 2012

I have broadband internet coming into 1 room of my home. The internet goes through a router I have set up, its a Linksys WRT54G2 (router #1), Firmware version 1.0.04. Everything on this works fine, I'm able to get my TV and laptop in a different room to access the router wirelessly without any inconvenience.In another room I have a regular desktop computer which I would like to get internet on. As well as other devices, so I purchased another router, this time a Linksys E4200 (router #2) in hopes of turning it into an access point.Now I've set up LAN's in the past, using the actual cable plugged into the second router, problem is in this scenario I can't run a cable over to router #2. Both computers use Windows 7. Both router's drivers and firmware have been updated on the Linksys page, all my Windows drivers are updated, etc. I checked other forums for similar questions and although there are some, they date back to 2009 as well as Google which has some websites dating back to 2006! While useful, I wasn't able to find something that details how to solve my problem with my specific setup. I've already gone into router #2 and changed the router's IP to 192.168.1.2 and also turned DHCP off, problem is, once I take that router off into the other room, it doesnt connect to primary network or allow devices to even "see" router #2.

View 2 Replies View Related

Linksys Wireless Router :: E4200 As Access Point / Bridge Mode?

Sep 6, 2011

I have spent most of the weekend trying to get this router to act as a proper Access Point.
 
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
 
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
 
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
 
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
  
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
 
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.

View 4 Replies View Related

Linksys Wireless Router :: E4200 Access Point To Maximize Coverage Throughout House

Jan 27, 2012

I bought two E4200s with the intent of using the second as a wireless access point to maximize coverage throughout my house. I just learned the hard way that the E4200 doesn't support that feature, and will only act as an access point if physically connected to the primary router that is connected to the internet.
 
Before I spend even more money on equipment, I was wondering if any of the experts here can tell me whether I can use a Linksys Bridge, like the WET610N or WES610N, to operate the second router in bridge mode and turn it into a wireless access point?

View 9 Replies View Related

Linksys Wireless Router :: E4200 / E3200 Or E2500 Better For Home Access Point?

Jan 18, 2012

I am looking form accesspoint for home network. I do not need router and usb functionality, I have this already in my linux server. I need only wifi accesspoint with 2 bands and 300Mbps bandwith. Is there a big difference between E4200 or E3200 or E2500? I know that E4200 supports 450Mbps, but I am not planning to buy new devices which could go faster than 300Mbps. Beside of technical parameters in technical specyfication is there a difference in wifi bandwith or tranmission between wifi and cable network?

View 9 Replies View Related

Linksys Wireless Router :: Change WRT320N IP Address To Use It As An Access Point?

Oct 9, 2011

When I change my WRT320N routers IP address to use it as an access point only and bring it in the IP range of my ccombined modem/router I'm not able to view the setup page via the new IP address. I have tried to change the IP from the default 192.168.1.1 to 192.168.178.2. After changing and applying the changes I restarted the router and tried to access the router via the new address. This was not possible am I doing something wrong or did I forgot something?

View 8 Replies View Related

Linksys Wireless Router :: Wrt54gs V7 And A Wap54g V3.1 - Unable To Get IP Address From Access Point

Mar 1, 2012

I have a wrt54gs v7 and a wap54g v3.1.  Both have latest firmware on them.  I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address.  is that right?).  I have them set on same subnet with static ip addresses.  They have same wireless ssid and password with one using channel 10 and the other using channel 2.  I can receive an ip address from the router and connect to internet.  I cannot get an ip address from the access point.  I tried a static ip on the computer and it will connect, but I don't have internet.  Am I missing something in the setup?  Can this access point act as a repeater for this router? 

View 3 Replies View Related

Linksys Access Point :: E4200 / E1500 - Cascading Routers Versus Access Points?

Nov 24, 2011

I am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.

View 3 Replies View Related

Linksys E4200 Can't Ping New Access Point

Jul 4, 2012

I have a Linksys e4200 and a EnGenius EAP300. I setup new EnGenius AP to 198.162.1.5 and the Linksys is 198.162.1.1. The two devices are connected with Ethernet capble with a POE switch in the middle. Internet connection thru the Linksys works fine. However, the EnGenius does not connect to the Ineternet (Gateway is set to 198.162.1.1) Also when connected to the Linksys, I cannot ping the EnGenius.

View 1 Replies View Related

Linksys Access Point :: E4200 - How To Upgrade

Jan 30, 2011

upgrading to an E4200 router.  What would be the best wireless access point to use with that?

View 6 Replies View Related

Linksys Access Point :: WAP54G As Range Expander For E4200?

Jun 25, 2011

I have just bought a E4200 and updated to latest FW version 1.0.02-Build13 It works very well for me so far But in the repote part of my home, the signal is too weak :-(
 
I have a WAP54G (HW-rev-2), which I would like to use to expand my wireless range, but so far I have not been able to get a setup where I can see the wireless coverage expanded. I have placed the WAP54G inside the wireless coverage range of the E4200 with good signal level.
 
I have tried various setup combinations and searched articles, but so far I have not been able to get this working as expected..
 
Before I spend more hours on this or decide to dump the WAP54G, I would like to know if this setup is at all possible with these components, - and of course if there are any hints to get this working ?

View 2 Replies View Related

Linksys Access Point :: WAP610N - Unable To Obtain IP Address

Dec 14, 2012

I bought a Linksys WAP610N today, i placed it so i could get a signal where i can't normally.
 
The thing is i configured it correctly, well at least i think, i can see it on my wireless network, with a good signal, but on my Android tablet (Google Nexus 7), it can't get past the "Obtaining IP address".
 
I called the technical support, the person there tried to assist me for about 1 hour, we tried different settings, we upgraded firmware from 1.0.01 to 1.0.04, but it didn't worked. Now he said someone will call me tomorrow during the afternoon.
 
My router isn't Linksys, it's a Netgear, i don't have wireless problem when i connect my tablets or any other wireless device on it, it's just that i bought this WAP610N to have the signal in my bedroom, where i don't get any signal normally.

View 7 Replies View Related

Linksys Access Point :: IP Address Does Not Show WAP54 But Netgear?

Feb 22, 2012

Trying to setup secure net but when I type in the router IP Address, it shows Netgear,  Type in printer IP address and it shows Linksys. How can I access my Linksys to make changes?  I believe the Netgear shown is Comcast modem...

View 9 Replies View Related

Linksys Access Point :: WAP54g Doesn't Recognize Laptop's IP Address?

Jan 9, 2012

I reset my WAP54g v3.05 to factory default to allow an older computer access to my network.
 
Now I've reinstalled it for better security using my newer laptop: no SSID broadcast and encryption set for WPA2-personal. However, when I enable Mac filtering and permit my newer laptop, the WAP54g does not recognize it.
 
Disable Mac filtering and my laptop is back on the network.

View 2 Replies View Related

Linksys Access Point :: E2500 Obtaining IP Address Timing Out While Connecting

Dec 5, 2011

I have a E2500 router and 3 WAP610N access points.  Users are having a difficult time connecting to the AP's.  The client device just sits there trying to obtain an IP and then times out.  If they get within range of the actual wireless router, then connect instantly.  Is there a setting to increase that will allow longer time trying to obtain an IP?
 
I am using the same SSID for roaming, but am using different channels (1, 6, 11) for the overlap.  See diagram below.  Not sure if this has some impact?

View 4 Replies View Related

Linksys Wireless Router :: E4200 Not Getting IP Address?

Dec 21, 2011

I have a 6 month old Cisco e-4200 router that is updated to the latest firmware, connected to a Motorola surfboard modem on Sudden-link in Midland, TX.
 
I previously used this exact same setup on Cox Cable in Wichita, KS with no problems. Upon setting it up down here I cannot get the router to pickup an IP address. I have Power-cycled everything multiple times, did a complete reset and re-installation of the router software and still no luck. The Sudden-link techs have no idea what is wrong. They said that the modems signal is strong and everything should be working.
 
Actually I did get it to work once for a couple of days, however when redoing the surround sound system I had to unhook the cable line and it quit working and I haven't gotten it to work again since. I have tried unhooking everything. Turning it all off. Waiting for 5+minutes, and then reconnecting in order: First the modem, then an ethernet cable to the computer which will usually work. But as soon as I unplug the cable from the computer and plug it into the router it stops working.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Cannot Get WAN IP Address From ISP

Jun 28, 2012

I just bought the Cisco e4200 v2 router, I did all the installations as the Cisco connect software instructed me and everything went fine.After the installation I configured the router on  the WAN settings as (Automatic Configuration - DHCP), like my old router (Linksys WRT54GL) and I saw that my router doesn't get the WAN address from cable modem from my ISP(it stays on 0.0.0.0), it doesn't renew the IP address.

View 3 Replies View Related

Linksys Wireless Router :: Lost IP Address E4200

Sep 3, 2011

My wife accidently reset the password on our E4200 wireless router and did not write it down. I have tried to reset the router as well as run the set up CD - no luck. How can I recover and get my wireless network back in operation?

View 1 Replies View Related

Linksys Wireless Router :: E4200 V2 - Block Public IP Address?

Feb 2, 2013

i got an E4200 V2 and it is updated to Linksys Smart Wifi firmware.. Is it possible to block a specific public IP address?

View 4 Replies View Related

Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?

Nov 1, 2012

How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.

View 1 Replies View Related

Linksys Access Point :: WRT54G - Unable To Find Access Point In Home Network

Aug 29, 2009

I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1.  My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
 
I found directions in the forum for a setup using the LG BD390  but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold  from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
 
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi. 

View 3 Replies View Related

Linksys Wireless Router :: E4200 (firmware 1.0.03) Fails To Renew IP Address

Dec 1, 2011

After an indeterminate period my E4200 (firmware version 1.0.03) stops renewing the Internet IP address. This happens in both router mode and bridge mode.In router mode the E4200 is set for DHCP and connected to the cable modem, in bridge mode it is connected to a Dell switch  with DHCP being provided by my Win2008R2 server.It appears that the device stops recognizing the existence of the Internet port - no lights come on when a cable is plugged in - whether connected to the cable modem or my Dell switch. Plugging the same cable into one of the 4 lan ports and that port lights up immediately (i.e. it is not a patch cable problem).If the E4200 is left switched off for some time (possibly days) it will work properly again for a while.

View 6 Replies View Related

Linksys Wireless Router :: E4200 Update DynDNS With Wrong IP Address

Jan 9, 2012

Frameware version: 1.0.03.
Environment: Internet (external IP say 24.x.x.x) ISP provided modem+router (192. 168. 1.x/ 24 IPTV network) E4200 (192.168.0.x/24 my home network).

The DDNS option page did report update succefully and shown the external IP address correctly on the page, however when I login to dynDNS it shows 192.168.1.x, which is the E4200 IP dhcp from the ISP's router.I know that it's double NAT, but the 192.168.1x/24 subnet is the IPTV subnet, and my old Dlink router did support and update the dynDNS entry properly.

View 4 Replies View Related

Linksys Wireless Router :: E4200 Received Response From Host (IP Address)

Jun 23, 2011

I replaced my old wireless router with a Cisco Linksys E4200, running firmware version 1.0.02 build 13  May 24, 2011.  About once a minute the router sends an unsolicited DNS message to the IPV4 multicast address 01:00:5e:00:00:fb with a destination IP address of 224.0.0.251.  The unsolicited message is a DNS response with source port 32784, transaction ID 0, flags 0x8400 (standard query response, no error), questions 0, answer RRs 2, authority RRs 0 and additional RRs 1.  The two answers both relate to the router itself: one has Name Cisco18738.local, type A (host address), class 1 (IN), cache flush true, time to live 1 minute, data length 4, and the address of the router.  The other is the reverse of the same address.  The additional record is for Cisco18738.local, type NSEC, class IN, cache flush true, time to live 1 minute, data length 5, next domain name Cisco18738.local, RR type A (host address).
 
When my desktop computer receives these messages it logs an error, for example: "Jun 23 07:39:22 sauterws02 avahi-daemon[1067]: Received response from host 10.146.9.1 with invalid source port 32784 on interface 'eth0.0'"  The 10.146.9.1 is the router's IP address.  I also see these messages on the wireless link from my laptop.I suppose the E4200 is generating these DNS messages in a misguided attempt to make sure there is no old information about its name.  Is there a way to turn them off?  If not, is there a way to report this to Cisco as a bug?

View 9 Replies View Related

Linksys Wireless Router :: E4200 Won't Give DHCP Address To Linux Boxes?

Sep 25, 2011

I've got threeLinux Boxes (running Centos 6).  They were all connected to my cheap WRT54GL--  DHCP worked every time.Absolutely no problems.  Both the LInux boxes and the WRT54GL had MTU set to manual, 1492.I replaced the WRTt54GL with the expensive E4200.  I set the new router's MTU to manual, 1492.  NONE of my Linux boxes ever receive a DHCP address.  I look at the logs, and they do DHCPDISCOVER, get DHCPNACK, try several different intervals, and then fail the interface and quit.ALL I did was unhook cables from the WRT54GL and plug into the E4200.  Yes, the WRT54GL was powered off.   NOTHING was changed in the Linux configs.  Yes, DHCP is enabled, address-range assigned, etc.  BTW--  one box is dual boot with Win7-- in Win7 (using the same card, obviously), DHCP works just fine.  But, Linux doesn't work.
 
I can give the boxes static IP's, and all is well.  Just can't get DHCP to work.  I evfen tried putting in DHCP reservations (via MAC assignments)  for the E4200-- still doesn't work. The new E4200 is on the 02 firmware (which I believe is cuurent). If I can't iron this simple task out, in a couple of days I'm taking the E4200 back, and getting a refund.  I'll stay with my old WRT54GL... it works.  Hate to give up on some of the new E4200 features, though.

View 2 Replies View Related

Linksys Wireless Router :: Cascading - WRT54GCv3 Doesn't Get IP Address From E4200 DHCP

May 21, 2011

I've tried to cascade two Linksys routers, but It hasn't worked for me. The first one (which has cable-modem connection) is the brand new E4200, and the second one is the old WRT54GCv3.[code] However, the WRT54GCv3 doesn't get the IP address from the E4200's DHCP. I've also tried to connect them directly (without the PLC), even specifing an static IP on the second router, but I got the same results.I've to state I don't want to change the first router IP/gateway parameters because I have a web and game home server working with an static IP and I don't want to put it offline temporarily because of readjusting network parameters.

View 9 Replies View Related

Linksys Wireless Router :: Changes In MAC Address Filter List Are Applied Only After Reboot Of E4200

Nov 26, 2011

I have noticed that changes in MAC address filter list are applied only after reboot of router. It is inconvenient.

Router Linksys E4200
Firmware Version: 1.0.03

Operation system on client computer is Windows 7.Can it be resolved in the next version of firmware?

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Setup After A Reset?

Jul 9, 2006

I had to reset my access point but the login screen fails to appear to lock the router.  I don't have the setup wizard disk.

View 9 Replies View Related

Linksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point

Jan 17, 2013

I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?

View 1 Replies View Related

Linksys Access Point :: WRT320N Access Point Vs Range Extender

Dec 14, 2011

Have a WRT320N router at one end of the house in the basement.  Would like to boost signal to other end of the house.  Which product should i use, an access point or a range extender?  My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.

View 1 Replies View Related

Linksys Access Point :: WAP4410n MIBs Or OIDs For Access Point

Jul 3, 2012

I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?

Apr 25, 2011

I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
 
 The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
 
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
 
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.

View 3 Replies View Related

Linksys Wireless Router :: E4200 - Acquiring Network Address In WAP / WAP2 Security Settings

Sep 11, 2011

I have E4200 with fixed ip 192.168.1.2, DHCP off connected through LAN ports to FIOS ActionTec as 192.168.1.1.  When connecting through wireless network off the E4200, I can obtain and connect fine under Guest network and WEP security, but for any other security setting, WPA, WPA2, Mixed mode, etc.  I get the message "Aquiring network address" forever, and I never get a connection.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved