Linksys Access Point :: WAP4410N Can't Set It Up

Jul 1, 2012

I need to set up some security cameras here, and the boss has a never used Cisco WAP4410N router. I gotta use my own personal laptop, it's a small netbook, Aspire One DN55E using Windows 7 and Firefox. The network switch is by ZHONE.The wireless accesspoint has green lights on power and wireless, but not on Ethernet or PoE. The switch has power as green, the status blinks green, and co mode is red, everything else is not on. The router is plugged into the first lan plug, I can't plug it in ethernet, as my plugs don't fit. My laptop is connected to the stitch in the secon hole, and the third hole on te switch is connected to the internet. My laptop is receiving wired internet, and it's working well. It's via comcast cable.Now, where it say's 'Configuring the wap4410N Access Point in the book that came with the router, under 'Launching the Web-Based COnfiguration Utility' I seem to from above already accomplished step 1, which is 'Connect your computer to the same network the WAP4410N Access Point is connected to.
 
Yet, in the next step, it says to configure to the same subnet access point.Now..... I've followed all sorts of things requiring me to do stuff with TCP-i4 and 6 in odd little places in my computer, I've typed in on my wireless network password the default access point in the book as well as the default mask, nothing. I went to firefox, and typed it in my browser, nothing- says each time it's taking too long.I can't configure it, the next step says launch firefox, and I can't pull this off, as firefox never finds that default address.This is too hard for something so simple. It shoud be plug in, software pops up on my computer, a quick wizard, and I'm done. It's been a few days, and I am sweating and hot and am thinking about reenacting scenes from terminator 2 at the cisco headquarters.

View 1 Replies


ADVERTISEMENT

Linksys Access Point :: WAP4410n MIBs Or OIDs For Access Point

Jul 3, 2012

I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?

View 1 Replies View Related

Linksys Access Point :: WRT160N And WAP4410N Repeater

Sep 15, 2010

I want to extend the range for a Linksys router WRT160N. I don't have the possibility to use an access point with a wired connection. I read on this forum that can be used WAP4410N configured as repeater, without wired connection. Can someone who has used this solution to confirm that it works? What configuration should be done on the router WRT160N to permit wireless signal to be repeated by WAP4410N?

View 5 Replies View Related

Linksys Access Point :: Setting Up AP2 WAP4410N To Be A Repeater For AP1?

Oct 12, 2011

I have AP1 setup with WPA2-Enterprise.  How would I setup AP2 (WAP4410N) to be a repeater for AP1?

View 1 Replies View Related

Linksys Access Point :: WAP4410N Won't Assign IP Addresses?

Dec 18, 2012

I have a Motorola Surfboard Modem connected to a Netgear 24-port switch. I bought the WAP4410N to provide wireless connectivity from the switch. All my PC's can get perfect connectivity via the switch but none of my wireless devices can connect at all. Sometimes I can get 1 PC to connect but what's strange is I can view my networked folders and such but cannot access the internet. I've upgraded the firmware to the latest May-2012. IPv4 and IPv6 are both set to automatic.

View 1 Replies View Related

Linksys Access Point :: Settings WAP4410N As Repeater For WRT120N

Jul 19, 2011

I bought my self a WRT120N as my wireless router for my house. and not a long ago i bought the WAP4410N, for my repeater (after i ask to some people).my house were concrete wall, it have about 15-20cm thick, and we try to avoid any wired LAN. The destinaton were unreachable with only WRT120N.it's look like this (what i want for the network on my home) : [code] i already tried to setting the WAP4410 as a wireless WDS repeater, and wireless client/repeater (with and without "Allow wireless stations to associate"). both were unable to connect (limited), although i get the signal. for the IP on the WAP4410N (192.168.0.50), i used static IP [IP, Subnet and Default Gateway were fill in] within the WRT120N range (192.168.0.2 ->192.168.0.51)
 
- how i configure my WAP4410N as a repeater?

- is there any settings that i must set on the WRT120N, before combining the WAP4410N?

View 1 Replies View Related

Linksys Access Point :: WAP4410N - Internet Connection Always Connect And Disconnect

Aug 18, 2011

I have a new notebook Sony Z217GG, I connected WAP 4400N was very smooth, but after connected WAP 4410N, the internet connecting always connect and disconnect, I check the notebook wireless model is intel 6230.

View 1 Replies View Related

Linksys Wireless Router :: Does Cisco WAP4410N Wireless-N Access Point Support PPPoE

Feb 21, 2013

Does Cisco WAP4410N Wireless-N Access Point support PPPoE ?If yes how can I configure the PPPoE conexion?

View 1 Replies View Related

Cisco Wireless :: WAP4410N Access Point

Sep 29, 2011

I recently purchased a WAP4410N and I have some problems getting it to work. I am on a 192.168.1 network so everything should be ready to go. I am unable to ping the default address 192.168.1.245 for the wireless. During the process of resetting the device I am able to ping it for a few seconds. I am able to see the wireless connection but I am unable to access it even though it is unsecured. All lights are on the device except the PoE light.

View 4 Replies View Related

Cisco Wireless :: WAP4410N - Monitoring Of Access Point

Mar 17, 2013

i have more then 25 Cisco WAP4410N AP put is our office. i put 4 AP in each floor.we are using signal SSID for all AP. I have two question

 1: want to monitor all AP if any is down we can trouble shoot it .

2: with some user have problem before connecting it show full signal but after connecting signal is drop.some time
connected PC is automatically restart wireless connectivity.
 
As a Admin i want to monitor what is going on.

View 2 Replies View Related

Cisco WAN :: Can't Access Point Admin Page (WAP4410n)

Feb 26, 2012

I'm having trouble setting up my WAP 4410n. I can connect to it wirelessly, I can ping it, but somehow when I try to connect to the admin intervace (in my case 192.168.1.36) I get the following error message:
 
"The connection was reset. The connection to the server was reset while the page was loading"
 
My I shut down my firewall, restarted my router, removed cookies and cleaned cache, but that's as far as my knowledge goes.

View 5 Replies View Related

Cisco Wireless :: WAP4410N Access Point Disconnect After Short While?

Jun 12, 2011

I got a CISCO wap4410n access point and it is disconnecting uses after a shorl while. I hv to again connect them manually.

View 1 Replies View Related

Cisco Wireless :: Wap4410n - Access Point Rejects The Username And Password

Jun 25, 2010

Recently I have purchased two brand new wap4410n access points.
 
I have connected my computer directly to one of the access points, and attempted to connect to the Web Configuration utility through my web browser.
 
I'm using a: 09' MacBook Pro, running Snow Leopard and Safari 5.
 
I can access the login screen of the access point, although when I enter the default username: admin and password admin, the login screen returns an error: Invalid username and/or password (or something to that effect). The URL changes to: http://192.168.1.245/login.htm&no=3.
 
I have reset the device by holding in the reset button for thirty seconds, powered down, powered up and re-attempted to login.
 
I still get the same error as above.
 
I have attempted to access the Web Configuration utility on both access points, and both access points provide the same error. I have also tried using the username: cisco and password: cisco.
 
Cisco, when contacted, said both access points must be faulty and I should replace them.
 
The probability of such an occurrence happening with two devices seems very low, and leads me to think there must be other factors at play. The only constant I can think of is the fact I'm using the same computer to access the devices.

View 4 Replies View Related

Cisco Wireless :: WAP4410N Increase Range Of Access Point By Replacing Antenna

Jun 17, 2011

I have a WAP4410N access point. In the datasheet, it shows that the Antenna Gain in dBi as 2. I need to increase the range of the access point by replacing the antenna with a 7dB one. I would like to know the maximum dBi supported by this access point.

View 0 Replies View Related

Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?

Nov 1, 2012

How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.

View 1 Replies View Related

Linksys Access Point :: WRT54G - Unable To Find Access Point In Home Network

Aug 29, 2009

I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1.  My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
 
I found directions in the forum for a setup using the LG BD390  but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold  from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
 
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi. 

View 3 Replies View Related

Linksys Access Point :: WAP54G Access Point Setup After A Reset?

Jul 9, 2006

I had to reset my access point but the login screen fails to appear to lock the router.  I don't have the setup wizard disk.

View 9 Replies View Related

Linksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point

Jan 17, 2013

I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?

View 1 Replies View Related

Linksys Access Point :: WRT320N Access Point Vs Range Extender

Dec 14, 2011

Have a WRT320N router at one end of the house in the basement.  Would like to boost signal to other end of the house.  Which product should i use, an access point or a range extender?  My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?

Apr 25, 2011

I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
 
 The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
 
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
 
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.

View 3 Replies View Related

Linksys Access Point :: Repeat WAP54G Access Point?

Aug 25, 2011

What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G. 

View 4 Replies View Related

Linksys Access Point :: WRT120N - Cannot Connect To An Access Point

May 10, 2013

I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
 
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.

View 1 Replies View Related

Linksys Access Point :: Configure WRT120n As An Access Point?

May 1, 2012

Is it possible to configure WRT120n as an access point?

View 1 Replies View Related

Linksys Access Point :: E3000 Configuration As Access Point?

Apr 6, 2011

I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.

View 1 Replies View Related

Linksys Access Point :: Way To Find Mib For WAP54G Access Point?

Feb 10, 2012

I have tried to find mib for my Linksys WAP54G acces point  without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?

View 1 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Linksys Access Point :: Cannot Access Configuration Page For WAP11 Access

Jun 12, 2007

Cannot access configuration page for WAP11 Access

View 9 Replies View Related

Cisco Wireless :: Point To Point Access Point 1262 Bridging

Feb 27, 2013

How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.

View 12 Replies View Related

Linksys Access Point :: Cannot Change Channel On WAP45 - Unidentified / No Access?

Jul 5, 2012

How do I change the channel on my WAP45. I can't connect I get a message unidentied-no access

View 1 Replies View Related

Cisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point

Apr 20, 2012

I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.

View 4 Replies View Related

Linksys Access Point :: E4200 / E1500 - Cascading Routers Versus Access Points?

Nov 24, 2011

I am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.

View 3 Replies View Related

Linksys Access Point :: Access Guest Account Through WAP54G?

Jun 9, 2011

My network is such that I want to extend the signal of the GUEST account.  I have a WAP54G set up for that purpose and am getting a very strong signal.  I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?

View 2 Replies View Related

Linksys Access Point :: Can't Access WAP54G After Firmware Upgrade

Apr 30, 2012

I just tried to upgrade the firmware of my WAP54G to the most recent version; however, I got a message on web browser with legend "Update fail" and then I lost the communication with device. Now, I just goty Power and Link LED's, but nothing on Act (green led, indicator of WiFi),I tried to reset using button, and to connect via LAN, but setup wizard is unable to locate the device.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved