Linksys Cable / DSL :: WAG120N - Double ADSL Connections On One PC?
Jul 11, 2012
I only have access to rather slow connections (256 Kbps). But since I have two lines and two modems, I was wondering if I could bond them together and make a faster one. My main modem is a Lynksys WAG120N Wireless-N ADSL2+ Modem Router, which as you can see is also in charge of both wired and wireless networks at my place. The second one is an older D-Link ADSL modem (JUST modem).Since I have an extra LAN port on my Lynksys modem, I want to know if and how I can connect the second modem, and combine the two rates.
I have a 3G USB modem connected to my desktop and I would like to share the internet connection to other devices wirelessly using the WAG120n ADSL router. How do I set up the IP's manually on the router and my PC to do this? And which other setting do I need to set?
Recently, i bought a LinkSys WAG120N ANNEX-A to replace my old speedstrem4200. Well everything was fine, but after 2 days of it installed, it started to drop my ADSL connection.
Sometimes, it remain connected for 4-5 hours, then drop, or sometimes, it drop every 30min-1hour.I tried upgrading the firmware to 1.00.16, but no luck, it still drop the connection.I have 3 computer plugged to the router via cable(wired) plus 1 netbook(wireless) and 1 ipod (wireless).Sometimes, when 1 computer is turned off, it seem to make the ADSL connection drop when the LAN light turn off. I noticed everytime it drop the ADSL connection, in the logs, i get this:
I'm using WAG120N, but suddenly Days back I am experiencing frequent disconnection after every 1-2minutes. After extensive Complains to my ISP (MTNL) they were unable to rectify the problem.Attaching the System Log of WAG120N. [code]
I've got Cisco X2000 and WAG120N. Is it possible to use one of those as a kind of a 'ADSL bridge' on to connected Sonic wall firewall ? How I picture it is that adsl connection is terminating on one of above Cisco boxes, which is connected via Ethernet or wan port to sonic wall, and it's only passing the adsl connection on to sonic wall which in result will end up with my ISP assigned IP address ?
I recently purchase WAG120N on a recommendation from a cisco personal, after my long year work horse Linksys AG 241 went kaput.Since I have purchased it WAG120N it is never stabilized on the MTNL ADSL network. There is too much of frequent disconnection. Although I have raised this issue with cisco support # 121128-000336 and 121122-004290, but all they have asked me to replace the WAG120N gateway. [code]
we are currently using a modem router LINKSYS WAG120N Wireless-N ADSL Router but are not satisfied. lots of dead zones and I think that there are too many users for this AP. last count gave around 20 users. so I'm looking for a solution to be able to handle 20+ concurrent connections and with large coverage - 600 m² .
On our 6504 - 12.2(33)SXH, we currently have a single connection to our ISP (GI1/1) and want to add another connection (GI1/2) Is there a way to bond the two connections to form a single connection (a single pipe) to double the throughput?
Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
I have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...
when choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
I am using WAG120N, and it keeps disconnected from internet randomly, normally between 5-10 minutes. The thing is, when it is disconnected, the adsl lamp is still on, so I think that it is not the network problem. When internet lamp turns off , I try to turn off the device (or unplug the phone cable), then turn it on again (or re-plug the cable), and it will work for certain minutes, then gets disconnected again. I already upgraded the firmware to v 1.00.12.
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
I have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?
I have multiple macs and when all of them are connected to the wag120n router, macs can't seem to find/see each other as if they are connected to different networks. I have tried another router ie. netgear dg834g router and this problem didn't occur and i am able to connect over the network without a problem. Obviously there is something wrong with the router settings.
We have a customer who has a WAG120N as their broadband wireless router, and we've sold them some new equipment, part of which is another WAG120N as our salesperson didn't realise they had one.They have a section of the building which the current WAG120N will not reach. Reading around this forum, it seems that I can give the second WAG120N a different static IP on the LAN and use it to expand the range of the WLAN.If I've read correctly, I need to make all the wireless stuff exactly the same except to use different wireless channels on each router. But what do I do with the DHCP server on the second WAG? Is it fair to say that the clients won't suddenly jump to a different IP because they won't have a cause to request a new one? I read one comment that suggested the second should be configured for DHCP relay, and another which contradicted this. Presumably I just don't configure the ADSL on the second WAG as that will only connect to the LAN.
Ok so for about a week now I have a problem with router. Today I checked log of router and found sometging like this:
Wed, 2012-12-26 15:41:15 - No response to 3 echo-requestsWed, 2012-12-26 15:41:15 - Serial link appears to be disconnected.Wed, 2012-12-26 15:41:15 - Enter: tdb_store.Wed, 2012-12-26 15:41:15 - tdb_store: calling tdb_update.Wed, 2012-12-26
I have BSNL Broadband with speed 512 kbps. My old modem gives me speed 0.54 mb . i have checked it on speedtest.net .But my new WAG120N gives me less speed 0.15mb .Why this so happen?i checked all settings