I have this problem since updating my firmware from 1.00.12 to 1.0016 (Annex A)
Problem: After leaving the router on for 1 day(dont know exactly how many hours), I tried logging in again on the admin page 192.168.1.1. Auth box appears, put username & password, but blank page after that. Tried using Safari/Firefox and it's the same. Router is working, all the LED lights are good, Internet is working, DHCP and all other config is normal. It's just that I can't access the admin page anymore.
When I power on/off the device, the problem is gone. Admin page is accessible again. But after some number of hours again, same problem blank admin page.
Does it has something to do with the router config like g.dmt/dsl 2 ?
Have problem with both of my wag120n routers. I setup remote access, from the intranet it works fine. But from internet instead of showing me the page it starts downloading it. Instead of home page trying to save ¨download¨, if i put a long link like xxx.com/setup.cgi?=etc then it tryes to save ¨setup.cgi¨. All fileas are empty, 7kbytes.
I don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
I recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1: Not shown: 65531 closed ports PORT STATE SERVICE 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 1780/tcp open unknown
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
I have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...
when choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
I am using WAG120N, and it keeps disconnected from internet randomly, normally between 5-10 minutes. The thing is, when it is disconnected, the adsl lamp is still on, so I think that it is not the network problem. When internet lamp turns off , I try to turn off the device (or unplug the phone cable), then turn it on again (or re-plug the cable), and it will work for certain minutes, then gets disconnected again. I already upgraded the firmware to v 1.00.12.
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
I have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?
I have multiple macs and when all of them are connected to the wag120n router, macs can't seem to find/see each other as if they are connected to different networks. I have tried another router ie. netgear dg834g router and this problem didn't occur and i am able to connect over the network without a problem. Obviously there is something wrong with the router settings.
We have a customer who has a WAG120N as their broadband wireless router, and we've sold them some new equipment, part of which is another WAG120N as our salesperson didn't realise they had one.They have a section of the building which the current WAG120N will not reach. Reading around this forum, it seems that I can give the second WAG120N a different static IP on the LAN and use it to expand the range of the WLAN.If I've read correctly, I need to make all the wireless stuff exactly the same except to use different wireless channels on each router. But what do I do with the DHCP server on the second WAG? Is it fair to say that the clients won't suddenly jump to a different IP because they won't have a cause to request a new one? I read one comment that suggested the second should be configured for DHCP relay, and another which contradicted this. Presumably I just don't configure the ADSL on the second WAG as that will only connect to the LAN.
Ok so for about a week now I have a problem with router. Today I checked log of router and found sometging like this:
Wed, 2012-12-26 15:41:15 - No response to 3 echo-requestsWed, 2012-12-26 15:41:15 - Serial link appears to be disconnected.Wed, 2012-12-26 15:41:15 - Enter: tdb_store.Wed, 2012-12-26 15:41:15 - tdb_store: calling tdb_update.Wed, 2012-12-26