Linksys Cable / DSL :: WAG160N Cannot Restore Configuration Backup

Mar 27, 2010

I have a WAG160N and its seems to have reset to factory defaults, no idea why, but when trying to restore the Configuration Backup all I get is "Restore Failure <Unmatched pid>"

View 2 Replies


Linksys Cable / DSL :: Getting WAG160N WAP Configuration?

Dec 20, 2011

I've just been sent a new ADSL modem router by my new broadband supplier and plan on using it.  However, my question is, can use my old wag160n to replace one of these, which im currently using to connect an old xbox to my wireless network, but also make use of the other lan ports on the wag (i.e. Connect more than one non wireless device to the wag and gain access to my wifi network?)

View 1 Replies View Related

Cisco :: 5508 - NCS Configuration Backup And Restore Of WLC

Jan 10, 2012

I recently tested the process for a customer of defaulting a Cisco WLC to factory configuration and then restoring the configuration from Cisco NCS.  It was not seamless to say the least and I wonder if I have just gone about it the wrong way. 
Have have set the NCS platform to configuration sync with the 5508 controllers at 04:00 every day and prior to the controller defaulting I ensured that NCS also reported that the config was in sync. I have also set NCS to complete a tftp backup of the controller every night 23:00 - interestingly though I have no idea where this is stored on the NCS platform ( a VM appliance ) or what it's file name is.
Anyway my experiences where as follows:-
1.  defaulted WLC and via serial CLI ended up at the configuration wizard.
2.  Set the correct LAG, management IP, host name that NCS knew this controller by.
3.  To test things just created a dummy WLAN ( SSID ) as I assumed this would be overwritten ( big mistake ! ). 
At this point I connected the controller to the network and tried to restore the configuration from the config sync version.

First problem - you have to remember to set up the SNMP community string you were using as it is needed by the configuration sync process.  After adding this to the controller I could push the configuration to the controller.

Second problem - failed to add the first WLAN from the backup as I have added the temporary dummy W LAN via the wizard and NCS reported a conflict.  So had to delete WLAN ID 1 from the WLC GUI directly and then the config push no longer reported this error.

Third problem - for some reason did not add the TACACS server details - reported the error that it could not added them.  I manually added these via a template via NCS and all was well. 

Fourth problem - all but the first WLAN was in the disabled state - had to re-enable all of the WLANs. 

Fifth problem - any default items I had disabled or removed have not been saved - therefore I have removed the public and private SNMP communities - but these were still on the WLC after the restore.  I have disabled unused ports not in the LAG as they show an error in NCS - these where not disabled after the restore.
So all in all not a very satisfactory restore process from NCS to an defaulted WLC ( meant to simulate to the customer what would be needed if they had to replace a controller due to hardware failure ).

View 1 Replies View Related

Linksys Cable / DSL :: WAG160N Blinking With No Ethernet Cable Attached To Router

Feb 24, 2012

I have a  WAG160N  wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset  ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.

What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ? 

View 1 Replies View Related

Linksys Wired Router :: RV042 - Convert EXP To Config File To Restore Backup Into New Router

Jun 7, 2011

I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?

View 1 Replies View Related

Linksys Cable / DSL :: Tweak SNR On WAG160n?

Mar 30, 2009

Is it possible to "tweak" the SNR on the WAG160n?

View 4 Replies View Related

Linksys Cable / DSL :: WAG160N And PPP Disconnection?

Jan 21, 2013

I've a 20Mbit/s connection with Telecom Italia provider.My line values follows:-- DSL Information ---DSL Driver Version: AnnexA version - A2pB023k.d21dDSL VPI/VCI: 8/35DSL Status: ShowtimeDSL Mode: ADSL2+DSL Channel:DSL Upstream Rate: 979 KbpsDSL Downstream Rate: 22105 Kbps Down upDSL Noise Margin: 12.0 dB 13.4 dBDSL Attenuation: 10.5 dB 4.3 dBDSL Transmit Power: 14.0 dBm 12.4 dBm?I have issues about connection stability : on HEAVY load download the PPP connection goes down. The sync signal stays up, but the PPP goes down!
In the log these lines corresponds:
Sun, 2013-01-20 23:29:29 - No response to 3 echo-requests
Sun, 2013-01-20 23:29:29 - Serial link appears to be disconnected.
Sun, 2013-01-20 23:29:29 - Enter: tdb_store.
Sun, 2013-01-20 23:29:29 - tdb_store: calling tdb_update.
Sun, 2013-01-20 23:29:29 - Enter: tdb_update.

My ISP says that there are no troubles with the line and it can be an issue of the modem...

View 8 Replies View Related

Linksys Cable / DSL :: Clarifications For The Wag160n-v1?

Jan 2, 2012

When I enable the debug with ?todo=debug shall I see more info in the logs ?How to stop the debugging ?How to print the logs ?What is the difference with debug and ppp_debug ?What is the effect of the sendlog command ? I didn't receive any email with a log !

View 3 Replies View Related

Linksys Cable / DSL :: WAG160N - Cannot Get Link

Nov 20, 2011

When i connect my WAG160N V2 to DSL, i don't get link, but if i tried whit a friend´s modem i get link. I use the same cables and dsl split.

View 1 Replies View Related

Cisco :: Backup And Restore LMS 3.1?

Apr 11, 2012

We have cisco works LMS 3.1  and the server have very problems, we need format the server and reinstall the Cisco Works, when I doin backup and restore of data LMS We lost the licenses? or when we restore the data in the server we have the same licenses? or get the new licenses to cisco?

View 5 Replies View Related

Linksys Cable / DSL :: Enable Airplay Using A WAG160N?

Aug 16, 2012

Struggling to enable Airplay using a WAG160N. Any settings I need on the router? Looking on forums, came across suggestion to disable WMM support. This seemed to work and i had Airplay but now I've lost it again.

View 1 Replies View Related

Linksys Cable / DSL :: Can't Access Gateway Of WAG160N

Aug 30, 2012

I hard reset the router WAG160N and i can't access it on, i can connect to the wireless connection but it shows unindentified network, in properties gateway IP is absent. i also get as IPv4.What could have happened to the modem, I can't use it at all at the moment?

View 3 Replies View Related

Linksys Cable / DSL :: Connecting Another Router To WAG160N?

Feb 21, 2011

Two years ago I bought a WAG160N for modem (ADSL) and router functionality. I consider to buy a pure router (E3000 or E4200) to connect to the WAG160N and use that one purely as the modem. How and what should I configure/disable on my WAG160N?

View 3 Replies View Related

Linksys Cable / DSL :: WAG160N Won't Connect To Internet

Mar 7, 2011

S/N: SSH00H406302
MAC: 001D7EB42921
Manufactured 04/2008
I can no longer access the internet, and the internet has been difficult to bring up for one to two weeks.Internet light does not come on. Under Status tab, interface is down, tried refresh and connect but nothing.The IP address can be pinged, 4 packets sent and 4 packets received. Tried resetting defaults and refreshing but no success.Bought this router in September 2008 to replace WAG54G which was constantly turning on and off every few seconds.

View 2 Replies View Related

Linksys Cable / DSL :: Why Cannot Register WAG160N Router

Dec 22, 2008

Why can I not register a WAG160N router with Linksys? Is this because these devices are not sold in the US?

View 4 Replies View Related

Linksys Cable / DSL :: WAG160N Rebooting In Loop?

Jun 16, 2012

Some years ago i have buyed a WAG160N i haven't never used, because once i plug it power, it start to reboot and reboot in a loop...Is there something to do with it or should i put it in the trash ? Firmware using is probably Ver.1.00.15?

View 6 Replies View Related

Linksys Cable / DSL :: WAG160N Internet Keeps Dropping Out?

Feb 4, 2011

I have a WAG160 setup to use the one fo the LAN ports as a WAN connection. The issue is every now and again the internet connection drops and it seems it is unable to communicate with the DNS server that is providing the internet connection.

View 9 Replies View Related

Linksys Cable / DSL :: How To Auto-reboot A WAG160N

Jan 25, 2011

Any hardware that can re-boot a DSL router such as the WAG 160N when the router no longer passes traffic ? Today, while the DSL line and the Internet appeared to be working, I could not  log in to the router from a LAN machine and I had to power it off and on again by hand.We have a number of surveillance cams on the LAN and this must not happen,  that the cams cannot be accessed, in particular if nobody is on site for a few days.Unfortunately, the WAG 160N does not have a daily re-boot option. What can one do except for installing a timer  that switches the power to the router off and and on again ? 

View 5 Replies View Related

Linksys Cable / DSL :: WAG160n Bridge Mode Only?

Nov 30, 2011

I'v just changed my internet provider. That new one uses Annex b, my wag160n is purposed to annex a. Thats what i'v done. Turn on bridge mode turn off dhcp, set  PPPoE with my login and password. And here is my problem. I cant connect by wifi with more then 1 device. I can only connect with my laptop when i'm trying to connect on my xbox it says it cannot get ip adress from router. What shoudl i change ?

View 6 Replies View Related

Linksys Cable / DSL :: Update Firmware WAG160N Not Possible?

Apr 19, 2013

i trried te update the firmware of my WAG160N. I had to choose between two versions. I tried both. But both versions give the message that is the wrong version and  the installations stops.

View 9 Replies View Related

Linksys Cable / DSL :: WAG160N Router Resetting Itself

May 24, 2011

I purchased a new WAG160N router a few months ago and recently I have been having major problems with connectivity.The problem is that it resets itself at seemingly random times. I see it happening. The red power light starts flashing red and then the other lights slowly turn green as it re-establishes connection to the internet.
This is becoming extremley frustrating as I do online gaming with my XBOX 360.I use wired connections using ethernet cables. One to my laptop. And one to my XBOX 360.I have contacted my ISP who have done line checks and I have had an engineer look at my line and all is good. I have also replaced all cables to/from the router including phone cords and ethernet cords. EVERYTHING is new.I recall one incident in which my internet was down and I just couldnt get connection AT ALL. I rang my ISP and they got me to log into my modem settings. The settings were all altered for some reason and I have no idea why. When they told me to enter the details in the settings the internet worked immediatley.

View 3 Replies View Related

Linksys Cable / DSL :: Wag160n - How To Disable Wireless

Dec 11, 2010

I have a wag160n and would like to disable the wireless and use as a wired ASDL modem. I can't see any obvious settings I'm the setup or buttons on the unit but was wondering if I were to set the DHCP to disable if

View 4 Replies View Related

Linksys Cable / DSL :: WAG160N Reboots Every 4 Seconds

Jan 7, 2012

My Linksys WAG160N has worked fine for 2 years however all of a sudden when I power it up it's start normal but after 4 seconds all ethernet lights blink one time and all start from the beginning, it's like it reboot every four seconds.It happens so quick I can't even get to the Internet/Network Settings in WIndows Control Panel.I have tried accessing router setup and installing firmware and both have failed - it can not find the network address.If I try to reset with the reset button on the rear (30sec reset), it stops rebooting and the power LED starts to blink red/green and the ethernet LED of the port where my cable is connected starts to blink alsoI have set IP address manually on my computer as per the Cisco support pages (, still no response from ping.I have also tried to reinstall firmware using TFTP but it also fails because it can not find the network address.

View 9 Replies View Related

Linksys Cable / DSL :: WAG160N - Cannot Connect To IP Address

Aug 10, 2012

I have a WAG160N wireless router that I want to use to repeat a wireless signal that is delivered by our ISP who installed broadband in our cottage, not our house (long story, we live rurally, so I won’t get into it).
So I understand I can simply plug my Linksys to power and that will pick up the signal inside our house (which it does, and we get an excellent strength signal).I further understand that I have to configure the Linksys so it talks to the modem provided by the ISP and which is about 50 metres awayFrom the Cisco website and my own docs I know the first step is to search the IP address online [url].,..

View 3 Replies View Related

Linksys Cable / DSL :: Replacing A AG241v2 With A WAG160N

Mar 24, 2011

I need to replace a failing AG241v2 and I am going to use a WAG160N.I problem is I notice there are two versions of WAG160N, v1 has a RJ45 port for the DSL and v2 a RJ11 port.AG241v2 has a RJ45 so the cable I was using was a Ethernet cable.Now this cable doesn't fit, of course it is bigger, I tried with a RJ11 cable but DSL light doesn't show up, it looks like it is not receiving any signal.Is there any adaptor or any cable to use WAG160Nv2 or should I replace it with a WAG160v1?
I found in several web stores when they talk about WAG160Nv1 they use the code WAG160N-E1 and for the WAG160N-v2 they use the code WAG160N-EW. Can they make it more difficult??

View 1 Replies View Related

Linksys Cable / DSL :: Transmission Power On A WAG160N?

Apr 15, 2012

I am trying to lower the transmission power on my WAG160N. I thought it should be an option in my advanced wireless settings of the web based setup page, however there is only transmission rate, n transmission rate and cts protection mode.

View 1 Replies View Related

Linksys Cable / DSL :: WAG160N Not Connecting Without Wire?

Jun 27, 2011

I buy WAG160n wireless-n adsl2+modem router with wire it works but it not connect without wire and i cant connect internet through my pc.

View 1 Replies View Related

Linksys Cable / DSL :: WAG160N - Wireless Connection Set Up

Dec 19, 2012

I have a WAG160N that I've used as a wireless router for ages. I have changed broadband providers and as they have supplied a new router I decided to use that and connect the old WAG160N via a Home Plug AV network and effectively use it as a range extender.
I have read some of the other forum posts and made the following changes:
1)   Set up internet as Bridge mode
2)   Set DCHP server as relay
When I connect via an ether net cable it works brilliantly but as soon as I try to connect wireless I can't talk to the internet. 

View 8 Replies View Related

Linksys Cable / DSL :: WAG160N Gateways Always Gets Disconnected

Aug 8, 2011

I have LinkSys WAG160N V2 with the last firmware 2.00.20 I have very annoying issue, the Gateway always disconnected from time to time .. Some days it work so fine and some days it disconnect 20 times per day and I have every time to go Status >> Gateway and press connect , another weird thing is that sometimes it gaves me speed 3784 Kbps and sometimes 3500 Kbps , sometimes it gaves me the right speed 4700 Kbps i did think maybe it's my ISP problem , but after the upgrade the problem gone for 3 weeks then it back again, and when it back I did make factory reset and reconfigure it again regarding my ISP settings and it did work fine with 3784 Kbps speed and it should be 4700 Kbps.

View 9 Replies View Related

Linksys Cable / DSL :: WAG160N Which Version Annex A Or B

Nov 15, 2011

I havce a WAG160N that is still on firmware version V1.00.16 andf I want to update it to the latest version.  I have seen on url...WAG160N that there is two versions to download - Annex A and Annex B under version 2.0.

View 3 Replies View Related

Cisco :: WCS Backup Restore Failed

Aug 21, 2012

I am facing a failed issue when restoring the WCS Database. Below is the error i get, does any one out there facing it before?
[root@egwgwcs WCS7.0.220.0]# ./Restore
Please enter the full path of the backup file name: /opt/WCS7.0.220.0/Backup_File/WCS_Aug2012.nmsbackup
Untaring the backup file...
Failed to untar backup file. Exception: invalid stored block lengths
Restore database failed.

View 1 Replies View Related

Cisco WAN :: Restore Backup From C2960 To Other One?

Jan 8, 2012

I want to restore a backup from c2960 to other one.Why is recommended to remove any security commands, like AAA?

View 2 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.1 Backup Restore?

Oct 20, 2011

I've been setting up building and testing our new ACS 5.x boxes and I've been running into a spot of bother with the backup restore feature. This most likely due to my unfamiliarity with the tool.

As part of my testing for Backup/Restore, I first backup the data using the Removal and backup  tool in Secure ACS View (found under data management. I then confirm that the new FULL backup has been populated my test repository and is available in the restore feature. (also under Data Management) My next step is to create a few test Network Device Groups, Identity groups, and users  Then I go back to the restore feature select the Back up file I just created, I also check the box Skip View Database backup before Restore and hit the restore button.
The box goes through the expected steps including a reload. When it comes back up I would expect the test users, groups etc I created after the last backup to be gone as they did not exist at that time. Although I find the opposite is true. Any settings I made after the last backup are still present. I do not have incremental backups enabled.
I essentially want to test a backup of the database of users and groups/rules etc make changes and then restore that database to the previous backed up configuration.

View 2 Replies View Related

Copyrights 2005-15, All rights reserved