I have 2 wireless routers with me. (Linksys WAG200G & USR 9111). Now, I am using USR9111 as the primary router. But, it not enough to provide network for the whole area. So, I have planned to add another router to this wireless network. Is it possible?
View 10 RepliesI have 2 wireless routers with me.
(Linksys WAG200G & USR 9111).
Now, I am using USR9111 as the primary router. But, it not enough to provide network for the whole area. So, I have planned to add another router to this wireless network.
I tried to set my WAG200G as a wireless bridge, but I encountered some problems doing so.
First I reseted the router to factory default settings, then I put it in "bridge mode only" disabled DHCP and UPnP (this was required for the college network I want to use on it to work). Then I put the UTP cable in one of the LAN ports.
When I try to acces this network though a wire everything works fine, I can see the other devices connected to the network and I can acces the internet. When I try to use the network wirelessly, I still see the other devices on the network but I can't connect to the internet. (The acces to the internet is gained by logging in inside the browser, like with wifi hotspots)
I got myself a HW500G as my main Wireless router. But as I moved to a new home with a very large space, I did start to have alot of dead spots which made me think about getting my old WAG200G out of the box and use it as Wireless extender.Is that possible with WAG200G and If yes, can you provide me with guidelines on how to do so.
View 2 Replies View RelatedI have a WAG200G as my ADSL modem and wireless access point. I would like to build two small wired networks that are remote from the location of the wireless access point (i.e. where my telephone line comes in) so that I can connect several network cabled devices in each location (e.g. NAS drive, TV, games consoles etc). I cannot run network cables to these locaations but believe that I can bridge them via the wireless. At a pinch, I could have only one cabled sub-network but would prefer two.
View 4 Replies View Relatedi did recently bought that new router to equip my house, also did a new firmware update to latest version 1.01.09 found on official website.
sadly it did kill my wireless network....
how to downgrade? im hardly looking on the internet for older version but cant find any..
I am basic user of Wireless WAG200G, I am using only as router,the problem is that i could set the wireless properly. When i restart the computer, I couldn't get internet access unless I go to ( 192.168.1.1) & do rebooting for the device. I believe that the setting are not correct.
View 2 Replies View RelatedI'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies View RelatedI have a network based on a SpeedTouch 706 modem/router, provided by my ISP. It is not possible to turn off NAT or DHCP on this device. Since it lacks wireless functionality, I added a Linksys WAG200G, by connecting LAN ports on both devices. Internet through WLAN works.
I would like to be able to manage the Linksys router/access point from an outside location, but I cannot get this to work.
The Linksys is configured for remote management on port 443 from any IP. The SpeedTouch is set to forward port 443 to the local IP of the Linksys. An nmap scan from the outside on my ISP-assigned IP on port 443 shows 'filtered'. If, as a test, I forward this port to my computer, nmap shows 'closed' (I have no service running on port 443), indicating that the portforwarding works. I chose 443 since somebody suggested that the Linksys device requires an https connection — I have tried different ports as well, to no avail.
My suspicion is that the remote management functionality only works through the WAN side of the Linksys router. It has no such port, though. Only 4 LAN ports and a 'line' port for the telephone line (unused). I would like to keep both devices — even though technically the Linksys could probably take over all functions from the SpeedTouch — because of the silly reason that both devices are not located in the same rooms, and already properly fitted in their respective places.
Possible using a firmware upgrade to change the wag200g from annex B to annex A?T
View 6 Replies View RelatedI have been using Linksys WAG200g as a modem&router at my home for few years already and it did a great job. Plugged it on 24hours non-stop. Default firmware.
However, in the past months WAG200g did the factory reset by itself. It happened once a month, 3 months in a row already. No body pressed the reset button nor use the web admin to reset it. It reset itself. All the SSID, IP Address, passwords, etc are reset to default.
Tried connecting my laptop...internet doesnt work. Tried doing restarts and stuff nothing seems to work.
View 1 Replies View RelatedI Have a WAG200G wireless modem but I can not activate VPN on my Phone 4 , but it is easily done by Zyxel modem.
View 4 Replies View RelatedI set the access restrictions as instructed but they refuse to work. Firmware version is :-1.01.05,have rebooted, with no success.
View 6 Replies View RelatedMy internet provider servers internet, telephone an digital cable TV to my flat.For using this, they sent me an AVM Fritz Box.It really works well..... except file transfers over LANWhen I try to copy more or less large files (above 4 GB) the Fritz Box fails, freezes or just drops all network connections...However: I hate this thing.
For my old provider, I brought my Linksys WAG200g and it really worked fine - due to this I'd like to install it the following way:
ISP -> Fritz.Box -> WAG200g -> LAN
how to update the firmware for WAG200G? I've downloaded the firmware from internet, but i don't know what to do next...
View 3 Replies View RelatedWell, I am just curious, how much hard disk does a WAG200G has? And how much memory and what processor? Is it hard to point me to a datasheet including every chip or/and component it has?
View 3 Replies View RelatedI want to connect my wag 200g to another router. My other router have ip address 192.168.2.1 and is connected to my isp and my wag 200g is 192.168.1.254. What i want is to connect my wag 200g to the other router and to share the internet connection. I want also the dhcp server on the wag 200g to assign ip address to the wireless users connected on the wag 200g with ip addresses to the network 192.168.1.0.
View 2 Replies View Relatedwhenever the phone is in use i.e. a call comes in or the phone is being used to dial out, the connection will drop. I have tried changing the microfilter on the Phone Socket, and it seemed to resolve it for a while.Should I perform a Factory Reset? I am using the latest firmware which is 1.01.06 ?
View 1 Replies View RelatedHaving the issue for over a year now, I'm wondering why there isn't a fix for the mentioned connection drops of the WAG200G? I'm on the newest firmware now (1.01.08(3)) but still every so many minutes: bam, lost connection.
View 9 Replies View Relatedwhenever the phone is in use i.e. a call comes in or the phone is being used to dial out, the connection will drop. I have tried changing the microfilter on the Phone Socket, and it seemed to resolve it for a while.
Should I perform a Factory Reset? I am using the latest firmware which is 1.01.06
I have a Linksys wag200g Modem/router and I need to change my Emails registered password.
View 4 Replies View RelatedMy IP provider has upgraded my broadband speed in early Jan. They require ADSL2. It seems to coincide with this date that I keep loosing my internet connection on a regular basis, say every 2 days or so, but not consistent. The cure is to unplug the linksys WAG200G ADSL home gateway. Plug it in again and all is well, until the next time. On the box it says the until is ADSL2/2+ compliant.
View 2 Replies View RelatedIs there a way through settings (I have a Linksys WAG200G modem/router) to slow the internet speed (much like shaping)?
View 2 Replies View RelatedI have connected CeeLab C300 video confernce system to our lan connectet to linksys wag200g. I have forwarded all the ports listed in manual to work without public ip. The problem is that system connect with our branch in other city, sound is great but i have no video on our tv. The other side has an audio and video but using public ip. Is a wag200g compliant to work with videoconferencing system? Support of the Ceelab ask me that Linksys is capable to NAT the H323 codec for audio & video/
View 1 Replies View RelatedAs soon as I set it up it would keep restarting every 3-5 minutes. It would sync with the ADSL line, wireless ok and then boom restart again.I've tried every singe setting, googled the problem, updated the firmware to the latest and still no luck.Then I had it replaced today with a new one and I faced exactly the same problem so I am thinking that eitherI am completely useless (which I would like to think I am not) or I got stuck with a batch of faulty X3000.Currently I am on linksys WAG200G that has been working non-stop for ages and the only reason I upgraded is that I wanted faster streaming.
View 9 Replies View RelatedI have a Linksys WAG200G wireless ADSL router. So it has one ADSL(phone) line input port , 4 Ethernet ports and wireless router. My router is fine and works well on ADSL connections. But as I have switched to Comcast DOCSIS modem based internet connection now, I want to to setup this router as "Home Gateway" only and not the modem. My intention is to use- use 1 of the 4 ethernet ports at the back of router as an INPUT . I want to put the ethernet output of the DOCSIS modem into this INPUT- and then i want to use the remaining 3 Ethernet ports as OUTPUT ports from the router.- I also want to work my router as Wireless router.
My query is- Is this possible ? Basically use 1 port as an input and 3 as output.- I have tried different things - Using Bridge mode only. DHCP disabled but sometimes only wireless works and other times only LAN bridge setup works but both do not work together.- Also at times, one Ethernet port will work as an INPUT and 1 as an OUTPUT but other two remain disabled.
I have an ADSL Modem WAG200G Annex A, with latest firmware. I recently purchased a Linksys E2000 to upgrade my wireless to N, plus to get 4 gigabit Ethernet Ports for my NAS.
The problem is, I set WAG200G to "Bridge mode only", and from within E2000, I provided PPPoE credentials (user name and password), it does not work, no Internet connection!
Normally, with the WAG200G, PPPoE credential is set as followings (and it works)
Type: PPPoE Multiplexing: LLC Virtual Circuit: "0" for VPI (0~255) and "33" for VCI (0~65535) "Keep Alive" option
on E2000 Router, PPPoE does not have the above option for me to select. Only User Name and Password field
I have a wireless router Linksys WAG200G.Im having trouble since a few days for use Windows Live Messenger 2009. I tried some tips for correct (cleaned cache, uninstall and re-install the software, checked the firewall, programs related to the software, etc).I was thinking that this was a trouble with my computer, but was made tests with other 3 computers, that cannot connect too (and can connect in others wi-fi connections, in other places) and in the attempts are being generated the same error: 8100030d.Searching in the internet, i saw that the problem could be with the router.
I didnt made any changes in the router configuration, and are using this equipment since last 2 years without any problem. I didnt tried to reset the configuration yet. But tried to disable the router firewall, and the problem occurred again.I tried some tips in this forum, like changing the MTU and including ports of messenger in the router configuration, but it didnt work.
I have been using a Linksys Wireless-G ADSL WAG200G, Annex-A Gateway Router and it has been fine, now my ISP have told me that they are modernising the network and will need a router capable of managing ADSL2/ VDSL connections, so will my router be able to do that or will I have to buy a new one? It has firmware 1.01.09?Edit: I see in the DSL Modulation menu which is set at present to "Multimode" I also have options to select ADSL2, ADSL2+, ADSL2 AnnexM, ADSL2+ AnnexM and ASDL2 AnnexL but I do not see any mention of "VDSL"
View 2 Replies View RelatedMy Linksys WAG200G worked like a charm in these 4 years, never had connection problems... the firmware was 1.00.09 One week ago i updated the firmware to last version (1.01.09) and now i have slow connection problems, sometimes it doesn't load web pages... I tried to hard reset and I tried to downgrade to different firmwares found on the web (1.01.01 and 1.01.05)What should I do? Is it possible to find the original 1.00.09 img?
View 1 Replies View Relatedis it possible to upload a htm file to the router using a command prompt? the page is located at [URL] I want to change the option of Allow All to Restrict Access at 8pm every night?
View 3 Replies View RelatedI have problems with my wifi router linksys wag200g.we have 2 pc in my home, and every time the other one connects to internet i lose almost 80-90% of speed connection.can i do something to limiting the speed of the other computer?
View 1 Replies View Related