Linksys Wired Router :: BEFSX41 Firewall Throughput?
Jul 12, 2007What the Firewall throughput is for the BEFSX41.
View 9 Replies
ADVERTISEMENT
Linksys Wired Router :: BEFSX41 Web UI Access?
Feb 4, 2012I've been struggling to resurrect an older V1 BEFSX41, which suddenly decided to suffer continuous collisions and loss of link. Had been running for several years. I reflashed the firmware with TFTP to 1.52.16.4, and reset for 30 seconds, and re-powered. I am unable to get any response form the web UI. I can ping 192.168.1.1, and obviously push the BIN image to it, but the UI doesn't give any sign of life - not even an error - just blank.
View 1 Replies View RelatedLinksys Wired Router :: BEFSX41 Won't Allow To Clear DNS Entries?
Feb 17, 2011I am trying to configure a BEFSX41 router which sits behind a Motorola SB 5120 cable modem. Somehow it now shows DNS entries on the basic setup page. Comcast advises me to zero out all those entries. When I make the attempt a message pops up saying the entry is invalid, and when I close the warning the entry reverts. The router is set to get its IP address automatically from the SB 5120.
View 3 Replies View RelatedLinksys Wired Router :: Firmware Upgrade For BEFSX41?
Mar 13, 2011I have been reading posts on this board that state that after upgrading the firmware on a router that you must re-set the router and re-configure your connection. I have just downloaded and installed the latest firmware update for the BEFSX41 (1.52.16.4). When the installation was complete, my network connection dropped out. I then got a "searching for ip address" icon in my notification bar. The connection then completed and my network seems to be running as it should. When I check the set-up screen for the router, it shows the new firmware version. Do I still need to re-set the router? I'm a bit confused by all of this. I have Comcast cable for my isp.
View 2 Replies View RelatedLinksys Wired Router :: BEFSX41 V1 Or V2 For Firmware Upgrade 1.52.16.4
Mar 19, 2011BEFSX41 Firmware Version to upgrade, version 1 or 2?
I've been using this router since 2006, upgrading the firmware to version 1.52.15 when released in 2007. At that time I think I selected the edition 1 rather than edition 2. Basing decision on the fact that the device had no indication of which model version was correct indicated on the manufacturing labels on the bottom. So I assume edition 1.
Is there any way to tell which hardware release I really have? Maybe by MAC address, or Serial number?
Have not had any problems with the 1.52.15 firmware version, however, I have seen numerous log entries for the following:
2011-03-20 11:45:23 ii=MAX_HTTPSESS2011-03-20 11:45:33 ii=MAX_HTTPSESS2011-03-20 11:45:39 ii=MAX_HTTPSESS
and
2011-03-20 10:53:09 UDP from 202.103.52.147:5060 to nnn.nnn.nnn.nnn : pppp(my ip address & port) followed by 2 to 10 of the following entries:2011-03-20 11:01:33 500 _upnp_Disable
the sending URL indicated as a PRC (Chinese) university with negative traceroute results, nothing really alarming as nothing is getting inside the firewall. Just packets dropped from the senders IP. I am keeping track of the pattern and activity levels.
Will probably just block the whole addy range at the router firewall and PC firewall. AT&T is totally ineffective in blocking this sort of back alley activity.
I've seen only one brief and somewhat dated reference to the "ii=MAX_HTTPSESS" entry and will tackle that issue after updating the firmware to 1.52.16, I haven't found any authenticated tech references for this. I can only make some educated guesses on tweaking HTTP settings.
Linksys Wired Router :: BEFSX41 Firmware Upgrade Doesn't Finish
Jun 6, 2009I'm trying to upgrade the firmware of a BEFSX41 wired router from version 1.43.3 (apparently the first revision after the original realease) to 1.52.15 (the latest I found), but I can't get it to finish. I'm using a Mac with all the latest versions of OS, Safari, and Firefox. When I use Safari to initiate the upgrade, it get's to the point where it says "Please wait ! Setup will take a few minute _____" and nothing else happens after that, even after waiting 30 minutes or more. When I use Firefox it gets to the same "Please wait" message, then a few minutes later Firefox displays an error message "Connection Interrupted: The connection to the server was reset while the page was loading. The network link was interrupted while negotiating a connection.
View 9 Replies View RelatedLinksys Wired Router :: BEFSX41 Creating Inbound Traffic Policy?
Feb 12, 2010BEFSX41 V2.1
Firmware: 1.52.16
The manual states how to create an inbound traffic policy but if you follow the directions there is no place to select inbound traffic.From the manual: To Create an Inbound Traffic Policy1. Enter a Policy Name in the field provided. SelectInbound Traffic as the Policy Type.2. Enter the IP Address from which you want to block.Select the Protocol: TCP, UDP, or Both. Enter the portnumber or select Any. Enter the IP Address to whichyou want to block.3. Select Deny or Allow as appropriate.4. By selecting the appropriate setting next to Days andTime, choose when the Inbound Traffic will be filtered.5. Lastly, click the Save Settings button to activate thepolicy.When finished making your changes on this tab, click theSave Settings button to save these changes, or click theCancel Changes button to undo your changes.I want to filter out a range of ip addresses from trying to connect to my network.
Linksys Wired Router :: BEFSX41 - Slow Downloading And Uploading On UTorrent
Dec 30, 2011I have an issue with slow downloading and uploading on u torrent with my wired router linksys BEFSX41. I thought it may be because I didn't set port forwarding on the specific ports the u torrent use.
But every time When I try to set new port forwarding rules on my router's control panel its asks me for a password and user. Although I know this password and user it will keep asking me about them without saving the new port forwarding settings.
Linksys Wired Router :: BEFSX41 Way To Determine Connection Speed On Internet Port
Jul 30, 2011I have a BEFSX41 connected to a Motorola SB6120. I changed my plan for a hgih speed, but did not see it.Had a tech out and we found when direct connected to my computer, I get 50 Mbps. When connected through the router, about 9 Mbps. I swapped cables, but still the same.
Is there any way to determine the connection speed on the Internet port? It seems that it only running at 10, when both the router and modem support 100.
Linksys Wired Router :: BEFSX41 Maximum Useful Cable Length Required For Connection
Aug 19, 2011I have a Linksys BEFSX41 wired router. If I wanted to connect a second computer to my router, what would be the maximum length of cable I can use without experiencing any problems ?
View 3 Replies View RelatedLinksys Wired Router :: BEFSX41 / Westell 6100G Modem - Setup And Configuration
Jan 10, 2012I have the Linksys BEFSX41 wired Firewall router. My ISP is Verizon DSL. The DSL modem is a Westell 6100G. I have the wall phone line connected to my modem. The output of the modem is going to the input of my Linksys router. I have two computers connected to the router outputs. In order for me to see the output or configuration of my Westall modem, I have to go http://192.168.1.1. In order for me to see the configuration of my Linksys router, I have to enter http://10.10.10.1. When I look at the instructions for setting up and configuring my Linksys router, it never mentions the above 10.10.10.1 address, but instead it tells me to enter the 192.168.1.1 address. I have never done this because when I powered both units for the first time, and it worked, I noticed then that my Linksys address was the 10.10.10.1. Why is it then that none of the settings or instructions for the Linksys router never mention to enter the 10.10.10.1 address as oppose to the one the do call out to enter which is the address for the Westell modem? What would happen if both addresses on both devices were the same?
View 2 Replies View RelatedLinksys Wired Router :: Cisco BEFSR 41 - WAN To LAN Throughput
May 9, 2011I have been trying to find out what the maximum Wan to Lan thruput is for the Linksys Cisco BEFSR 41 Etherfast router..
Have both the version 3 and 4 models and want to deploy them into both 6mb and 12mb DSL networks.. From what I have found the version 1 and 2 have 10mb wan ports and the version 3 and 4 have 10/100mb ports.. There seems to be hardware upgrades as well with the CPU and memory speeds but what they are I do not know for sure.. Found someone stating that they went from a 50mhz CPU to a 166mhz CPU to a possible 220mhz CPU...
Linksys Wired Router :: Getting RV042 And RV082 Throughput?
Feb 17, 2008I am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.
View 9 Replies View RelatedLinksys Wireless Router :: BEFSX41 - Devices Missing In DHCP Client Table
Aug 7, 2006I recently installed a WRT54G wireless router however I has this same question about my BEFSX41 Wired router.
View 9 Replies View RelatedLinksys Wired Router :: Cisco RV042 - Firewall Blocks Mails?
Dec 10, 2011 I have a Cisco RV042 Wired Router. I've got a static IP and a MS Small Business Server in my Router Network. I have forwarded the essential ports to use the IIS and the Exchange Server of my SBS2011 (https, http, smtp, rpc).
I can use the IIS, if the firewall is activated, but the exchange Server can not receive any emails. I have also created some firewall access rules for the mentioned services but without success.
Linksys Wired Router :: Does RV042 Firewall Support Port Forwarding
Aug 5, 2011I am using an RV042 router/firewall -- firmware v1.3.13.02-tm -- connected to a cable modem.I have one public address (WAN1) assigned by my ISP's DHCP server.All my machines on the LAN have static IPs. (RV042 DHCP Server is disabled.)I have set up port (80) forwarding to 192.168.1.101. The HTTP port forwarding does work if an http client on the LAN sends a request to url...But I cannot get a response if I send a request to url... from a machine on the WAN.I did configure Access Rules to allow http traffic (and then tried to allow *all* traffic) between a single IP on the WAN and 192.168.1.101.
The incoming log table shows a connection is made from the http client on the WAN to the correct http server on the LAN, but there is no resonse from the LAN to the WAN.Is my configuration the problem, or is this feature not supported by the RV042 router?Could my cable modem be blocking outbound traffic?
Linksys Wired Router :: RV042 Port Forwarding And Firewall Rules?
Oct 31, 2011I have a system with a RV042 managing the internet connection.Behind the RV042 I have an e-mail server and a development machine that I access through SSH.My problem is that if I forward port 25 to my internal e-mail server it bypasses the firewall rules.I have an external vires and spam scan host that is the only one I should accept incoming email from - but it seems that whenever you add a portforward then it bypasses the firewall rules.
View 1 Replies View RelatedLinksys Wired Router :: CISCO RV082 Slow Internet Connection With Firewall?
Nov 14, 2012I'm owner of Cisco RV082 router and I have a problem with firewall setup.I would like to deny internet access on port 80 (all sites) for group of users, and allow them internet access for one site by HTTPS (443)After applying rules internet connection is really slow.. Users have to wait something like a 30 sec for a website..I descovered that the reason for slow internet connection is DENY rule. After disbling DENY rule everything works fine..Now I have a few rules added to firewall:
Priority:1 Action: Deny Service: HTTP(80) Source interface: LAN Source:10.82.0.51-10.82.0.245 Destination: Any
Priority:2 Action: Allow Service: HTTPS(443) Source interface: LAN Source: 10.82.0.51-10.82.0.245 Destination: 80.64.59.42
What's wrong with those firewall settings?
Linksys Wired Router :: RV016 - Allow Other Networks Connected To Firewall To Access Internet?
Nov 24, 2011I have a sonicwall firewall connected to the LAN port of the RV016 router and two DSL modems connected to the WAN ports.
Ip address allocation:
Firewall
192.168.50.9
RV016
LAN - 192.168.50.10
WAN - 192.168.60.1
WAN - 192.168.61.1
What configurations do I need to enter into the RV016 to allow other networks connected to the firewall(192.168.3.0, 192.168.2.0) to access the internet?
Linksys Wireless Router :: Very Low WAN Throughput On WRT160NL
Jun 11, 2012I recently bought a WRT160NL router. I have a 10/10 Mbps internet connection, but when I am connected via the router it only gives me ~2.5/1 Mbps speeds. Connecting my computer directly to the "wall" results in 10/10 Mbps speeds. I have tried connecting to the router both wireless and by wire, it makes no difference. The internal wired and wireless speeds are fine, as I have copied files over the internal switch and via the wireless network at relatively high speeds. I have not fiddled with any connection settings except creating a few permanent DHCP leases.
View 6 Replies View RelatedLinksys Wireless Router :: E4200 Wan To LAN Low Throughput
Jun 22, 2012I have a E4200 V1 with 1G internet connection, when i connect my PC, with a cat6 cable, directly to the modem the download speed can upto 800Mbs, but when i connect through E4200 to the modem it down to 100Mbs.
View 1 Replies View RelatedLinksys Wireless Router :: Low Throughput With E2500
Feb 1, 2012I have a E2500 connected via LAN to my network via a switch or hub through a sonic wall and into the modem out to the internet. The problem is that I am only getting +/- 5Mpbs Down and +/-7 Mbps up through the router.
If I connect my computer to the network with out going through the router my speeds are more in the range of +/-28 Mbps down and 16Mbps up. I have been working with Linksys support but they have not been able to assist me with this yet! Is there any configuring I should be doing at the firewall or to the router to tell it to open up the port for faster speeds?
Linksys Wireless Router :: E4200 With Proper Throughput?
Feb 12, 2012I have an E4200 running firmware v1.0.03.Works fine for a period of time (might be hours, might be days) then throughput drops to something in the range of 1-3M when typically I'll see 6-8M (DSL). I can reset the DSL modem, hubs, etc but the problem isn't fixed until I reset the E4200; so I've pretty much narrowed it down to the router.
View 1 Replies View RelatedLinksys Wireless Router :: E3000 Max Throughput For Internet And Usb Nas
Dec 25, 2010I have been running some test to see what I can do for speed to the interenet and NAS drive.I have a NIC card (1394) and the max connection I get is 400 Mbps. The card is suppose to be 10/100/1000 card and E3000 is the same... so why can't I connect at 1000?Max transfer I get to my NAS is 64-80 Mbps. Is there any way I can get this to be faster? I have a 1TB western digital drive attached.If I went with a NAS system like a Synology BYOD system could I get faster speeds for transfers if the NIC on the system was a 10/100/1000?`
View 5 Replies View RelatedLinksys Wireless Router :: EA3500 Gigabit LAN Throughput Degraded
Aug 13, 2012I have a 500Mbps Internet Connecton with fibre and I bought an EA3500 recently. I found the LAN through put degraded by compare connected and not connected with EA3500.all connections are using CAT5e cable with all Gigabit port enabled in PC/ISP Router.
View 9 Replies View RelatedLinksys Wireless Router :: E4200 Can't Get Over Ca 10MB/s Data Throughput
Dec 27, 2011I'm using E4200 (fw 1.0.03) as AP and EDIMAX 6675nD as a client. I can't get over ca 10MB/s data througput even there aren't any other communication loads. Test conditions are: 5GHz band, no other networks in the band, distance 2m without any obstacles, no other data transfers (except the test), data source is NTB on GLAN port of Linksys, data sink is NAS at GLAN port of Edimax, test file is 0.5GB file. The NTB and NAS doesn't seems to be a bottleneck, because NTB connected directly to the Edimax does over 50MB/s. Both the E4200 and 6675nD are (should be) capable of 450Mbit/s @ MCS23. Strange thing is that none of them allows setting of MCS23 in their manual settings. It ends with MCS15. While forcing the E4200 to a specific MCS (in the hidden wireless_advanced menu) the MCS15, 14, 13 and auto give very similar results. The throughput drops by MCS 12 and lower indexed MCSs.The 10 MB/s seems to be a low number.... and (based on internet forums) I'm not the only one fighting the magic number 10MB/s. What is the reason of the ca 10MB/s bottleneck? And the resons why both of the routers are quiet about the MCS16 to 23 schemes in their menus, while their labels aren't?
View 4 Replies View RelatedCisco Firewall :: Upgrade From 5505 To 5520 On Network - ASA Firewall Throughput
Feb 27, 2013I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
Linksys Wireless Router :: E2500 Getting Slow Throughput With FIOS Quantum
Aug 14, 2012I've just upgraded to FIOS quantum service. (50 MB down, 25 up). I have a Linksys 2500 connected to the FIOS router. The FIOS (ActionTec) router provides the full advertised speeds with any speed test service I try. But with the 2500 connected to the FIOS router I get download speeds about 3MB. The MTU on the linksys is 1500. It's connected correctly and is running it's own DHCP server. (Why am I doing this? I try to avoid the ActionTec routers, they have broken many services in the past.)The 2500 firmware is up to date. I've tested on the wireless and wired (ethernet) interfaces.
View 2 Replies View RelatedLinksys Wired Router :: EA4500 - Wired Connections Have Long Ping Times
Sep 23, 2012I purchased and set-up the EA4500 on Thursday. Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues. Connected directly to modem I get normal ping times on whichever computer is connected. When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms. They are all over the place 30ms (I can live with that), up to the 900's. I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference. I did end up doing a hard reset on the router last night after I lost tech support. We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
It was so slow on my work computer, a pint to yahoo timed out. The computers connecting to router are
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP
Linksys Wired Router :: E2000 - Security Wired Ethernet Connections
Sep 19, 2011I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive. I am planning to allow a tenant in another building connect via an ethernet cable connected to my router. Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router? I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.
View 1 Replies View RelatedLinksys Wired Router :: E4200 No Longer Accepts Wired Connections?
Oct 11, 2012My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies View RelatedLinksys Wired Router :: BEFSR41 Two Wired Routers In Non-standard Hookup
Sep 14, 2011I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off). All computers and other devices connected to it are manually IP configured. I desire to add a device that cannot be manually configured, and needs DHCP. I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network). The new device needs two-way internet access, but doesn't care if it sees any other current network devices. I've tried several configurations, none seem to work.
View 3 Replies View RelatedLinksys Wired Router :: BEFSR81 Keeps Losing Wired Connection To WAP54G?
Apr 11, 2012I have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81. I'm not sure if this is an issue with the WAP or the router.
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time. I used to have the power settings such that it didn't power down completely even after a long time. With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died. The wireless link would report that it had a solid connection, but I couldn't connect to anything. Power cycling the WAP always fixed this.
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours. Now, it seems I can't even go one day without losing my connection.
I am running the latest frimware in the WAP, and the router is version 3.1. I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen. I know from past experience that I will have to power cycle it to get it to talk to me again.
In any event, it seems like the router connection to the WAP is timing out. I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.