Linksys Wired Router :: Create VPN Tunnel Between Two RVS4000s Through WAN?

May 14, 2012

I am trying to create a VPN tunnel between two RVS4000 Routers through a WAN.  I get the following error when trying to do so.
"remote Security Group" and "Local Security Group" can't be in the same network.

View 1 Replies


ADVERTISEMENT

Linksys Wired Router :: RVS4000 Create IPSec VPN Between Main And Branch Office

Aug 2, 2011

We have used two Cisco RVS4000 to create the IPSec VPN between the main office and the branch office. The main office has SBS 2008. There is a Windows Server 2008 as the domain controller in the branch office. One branch office user has a laptop which is not in the domain, but his exchange account is set up in the Outlook. When he connects the laptop to the branch office network, he cannot connect to the exchange server and get the emails. Is there any configuration to set up in the router, server or Outlook?

View 1 Replies View Related

Linksys Wired Router :: Rv042 Vpn Tunnel - Can't Access HTTPS

Dec 7, 2011

i have 2 rv042 with a vpn tunnel between them.the problem is that i can't access https over the VPN !if i telnet 192.168.10.1 443 through the VPN, it's not working either. if i telnet 192.168.10.1 443 in my 192.168.10.0 network it's working so it's reall the VPN tunnel the problem.

View 1 Replies View Related

Linksys Wired Router :: First And Second Location RV042 - VPN Tunnel Configuration?

Jan 14, 2011

Setup is two dynamic IP locations

1. first location RV042 is the gateway attached to ADSL modem

2. second location RV042 is behind BT home hub gateway - for now the BTHH DMZ is enabled to the RV042
 
Followed the user manual config for two dynamic IP but it seems that the RV042 behind the BTHH obviously has a different IP than the resolved IP and is causing problems with connection.

This from the log file:
Jan 14 15:04:16 2011    VPN Log   Received Vendor ID payload Type = [Dead Peer Detection]
Jan 14 15:04:16 2011    VPN Log   [Tunnel Negotiation Info] <<< Responder Received Aggressive Mode 1st packet
Jan 14 15:04:16 2011    VPN Log   Aggressive mode peer ID is ID_IPV4_ADDR: '192.168.95.139'
Jan 14 15:04:16 2011    VPN Log   No suitable connection for peer '192.168.95.139', Please check Phase 1 ID value
Jan 14 15:04:16 2011    VPN Log   initial Aggressive Mode packet claiming to be from 81.156.xxx.xx on 81.156.xxx.xx

But no connection has been authorized,check peer ID Is there some way of making the RV042 behind the BTHH properly identifiable to the other end?

View 1 Replies View Related

Linksys Wired Router :: VPN Tunnel Disconnect Between RV016 And RV082

Jun 2, 2011

Currently I have a VPN tunnel setup between our company locations. Location A has Linksys RV016 and Location B has RV082.  Everything has been working with no problems for the past 2 years with only minor disconnect issues in the VPN tunnel between the locations.
 
For the past 2 weeks I have been running into issues with the Tunnel. Users in Location B are reporting problems with losing connection to applications that are hosted in Location A. At first I start with doing a ping to router address in Location B and I get "request timed out". Next I login to router in Location A and under VPN I notice that the VPN tunnel is not disconnect (I see disconnect button). Once I click on Disconnect the screen refreshes and that seemed to restablish connecting with router in Location B. The drop connection has been been going on for the past 2 weeks and only happens once a day specifically between 1 PM and 3 PM EST. I have been reading all over the internet and no luck at all. The VPN tunnel settings are the same on both routers and under Advanced options both Keep Alive and Dead Peer Detection (DPD)  are checked.

View 1 Replies View Related

Linksys Wired Router :: RV042G Dual Gigabit WAN VPN Tunnel?

Jan 30, 2013

Is it possible to configure the RV042G so that one WAN port is connected to an ISP with a static IP and the other to an ISP with a dynamic IP.   Then, I would like to setup a VPN tunnel and use the static IP for that and have all the other internet traffic go through the dynamic IP. 
 
I know I could set it up with the static IP as the primary and the dynamic as the backup.  Then, if I lost connectivity on the static IP, I would still have internet access, only the VPN tunnel would be down. 

View 1 Replies View Related

Linksys Wired Router :: Setup VPN Tunnel Between RV082 And WRV200

Feb 23, 2011

I'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.

View 1 Replies View Related

Cisco VPN :: Create VTI Tunnel From 877 Router To ASA?

May 13, 2012

I woulke like to know is it possible to create a VTI tunnel from my 877 router to my ASA, rather than creating a cryptomap on the router ?

View 1 Replies View Related

Linksys Wired Router :: RV042G / Create Service To Forward Public Port 9010 To Internal IP Address With Port 23?

Oct 12, 2012

Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?

View 1 Replies View Related

Cisco VPN :: Can 881 Router Create L2TP / IPsec Tunnel Via NAT

Feb 23, 2011

Successfull in setting up an L2TP/IPsec tunnel through NAT-T against a Windows 2008/ R2 RRAS server? I am using an 881 router and the layout is someting like this:Client -> 881 -> NAT -> internet -> Windows 2008 RRAS.The tunnel goes form the 881 to the Windows server (not from the client...).

View 4 Replies View Related

Cisco VPN :: Create VPN Tunnel Between ASA5520 And 2921 Router

Sep 21, 2011

I am getting the following errow message while trying to create a VPN tunnel between an ASA5520 and a 2921 router. [code]

View 9 Replies View Related

How To Create Wifi With Wired Modem Router

Aug 18, 2011

Is it "possible to create a WiFi" or make my desktop using hardware connection, a hotspot? (Without buying a wireless router/modem/card) I mean, is there a tweak or program I can download to configure my desktop running on Windows 7 to create wi-fi? The reason why I'm interested in this it's because, for Bluetooth, it's possible. Just wondering if they have the same nature with WiFi (In terms of configuration and tweaks)^,

View 7 Replies View Related

Cisco :: How To Create Ipsec Tunnel

May 4, 2011

how to create ip sec tunnel using these parameters. customer ip where tunnel has to be connected 1.1.1.1

ISAKMP Parameters: (Phase I)
Encryption: AES-256 or 3DES
Authentication Mode: Pre-shared key

[Code]......

View 4 Replies View Related

Cisco VPN :: 5510 - How To Create ASA / VPN Tunnel

Jun 11, 2013

We currently run dual ASA 5510's in A/S config on our main campus. We would like to create a VPN tunnel to a branch campus. Trying to decide between a 5505/5510/5512x, We would like to extend many of the capabilities of our network to the branch campus which will be 20-50 users on a 50mb/10mb internet connection.
 
Domain login
System Center workstation management
Cisco WCS
Shoretel voip
(Cisco NAC?)
 
Several different VLANs for wireless guest, student traffic, staff traffic, voip traffic, etc. Which device would be best and should we get the security plus license with it?

View 4 Replies View Related

Cisco VPN :: 5505 Create VPN Tunnel Between Two Offices

May 27, 2011

I have two cisco ASA 5505 devices and two cisco switches plugged to ASAs in each office. I need to create a VPN tunnel between two offices.
 
-Network behind the ASA1 in office1 is 192.168.1.0/24 with DHCP server – 192.168.1.10
 
-Networks behind the ASA2 in office2 are 192.168.5.0/25; 192.168.5.128/26 and 192.168.5.192/26
 
 All computers in office2 need to get IPs from DHCP server 192.168.1.10. I have switch in office2 with 3 VLANS and I can assign computers from different subnets to different VLANs.How can I archive this goal? Should I assign 3 IPs for ASA2 inside interface (192.168.5.1, ...5.129, ...5.193) as a default gateways for each subnet? Should I put dhcp helper address 192.168.1.10 on the switch for each VLAN?

View 4 Replies View Related

Cisco VPN :: VPN 3000 Setting Two Concentrators At Different Sites To Create Ipsec Tunnel

May 20, 2011

I'm currently setting up two VPN 3000 Concentrators at two different sites to create a IPsec LAN-to-LAN Tunnel. I have gone through all the basic configuration guides on the CISCO site, but a LAN-to-LAN session is never created. I have enabled the logs on the Concentrator and it displays no errors at all - it appears the Concentrator is not even trying to establish a IPsec LAN-to-LAN Tunnel.After running through the standard setup provided by CISCO, is there anything I need to do to make the Concentrator try to create a Tunnel, or should this be automatic once all settings are in place?

View 2 Replies View Related

Cisco Routers :: Get The RVS4000s DHCP Server To Assign Another IP Address?

Feb 4, 2013

I have a RVS4000 router with DHCP enabled and in router mode. 
 
The LAN is 192.168.2.x.  The RVS4000 static IP address is 192.168.2.8
 
The router is not the RVS4000 and is at 192.168.2.1
 
The RVS4000 dhcp is assigning it's clients a default gateway of 192.168.2.8 instead of what I want 192.168.2.1. How can I get the RVS4000's DHCP server to assign another IP address other than its own as the default gateway to its DHCP clients?

View 2 Replies View Related

Cisco Routers :: Setting Up Static Routing Using Multiple RVS4000s

Oct 8, 2011

I have 8 RVs4000's to built a test system with. On each side of the network is 2 servers, both with 2 NIC's. Both are on different /24 networks.

The idea is to simulate a WAN link, with the RVS4000's G1 & G2 running in "Gateway" mode to simulate the WAN.  All other RVS4000's will be in Router mode ('R1,R2...etc..')  All networks in /24 range. As I understand it, the RVS4000 CANNOT take 2 diverse networks on the LAN side: - ie 192.168.168.1 & 10.1.1.1 on the LAN side. The NIC's on the server only need to communicate to the similar type of addresses on the other side - 192.168.168.1 on server 1 to 192.168.170.2 on server 2, but NOT 192.168.168.1 to 10.1.2.1 on server 2. The G1 & G2 link is so that all communications are routed between this link - as a testing point.
 
So, my questions are this:
1) Will this work? Is there any easier way of doing this? (Bear in mind this is the only equipment i have to do this). 
2) Is the static routing I have thought of work? (see below)
 
R1
0.0.0.0 0.0.0.0 10.1.1.10
R2
5.5.5.0 255.255.255.0 10.1.1.100
4.4.4.0 255.255.255.0 1.1.1.200
[code]....
 
I know using the RVS4000's inbuilt RIP may be easier, but I've never configured RIP routing.  As this is a test environment, using static routing would be enough to get it going.  No security lock down is required, all I'm trying to enable is for the servers to communicate with each other (NIC1 on both servers e.g 10.1.1.1 on server 1 to 10.1.2.1 on NIC 1server 2, and NI 2 on server 1 192.168.168.1 to NI 2 on server 2 192.168.170.1)  The 10.1.x.x networks DO not need to talk to the 192.168.x.x networks.  THe G1 & G2 link is just for testing - but all communications must pass through here and be routed to their relevant networks on the other side.

View 4 Replies View Related

Cisco Switching/Routing :: ASR 1001 - License Required To Create IPSec Tunnel?

Oct 26, 2011

what license do I need to create a IPSEC tunnel? I have an ASR 1001, running? [code]

View 2 Replies View Related

Cisco Routers :: RV042 VPN - Create Tunnel But Unable To Connect Using Windows Connection?

Jul 18, 2011

Im able to create a gateway tunnel with two rv042 routers in different locations  ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
 
Message was edited by: Adrian Torres

View 7 Replies View Related

Linksys Wired Router :: EA4500 - Wired Connections Have Long Ping Times

Sep 23, 2012

I purchased and set-up the EA4500 on Thursday.  Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues.  Connected directly to modem I get normal ping times on whichever computer is connected.  When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms.  They are all over the place 30ms (I can live with that), up to the 900's.  I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference.  I did end up doing a hard reset on the router last night after I lost tech support.  We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
 
It was so slow on my work computer, a pint to yahoo timed out.  The computers connecting to router are
 
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP

View 5 Replies View Related

Linksys Wired Router :: E2000 - Security Wired Ethernet Connections

Sep 19, 2011

I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive.  I am planning to allow a tenant in another building connect via an ethernet cable connected to my router.  Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router?  I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.

View 1 Replies View Related

Linksys Wired Router :: E4200 No Longer Accepts Wired Connections?

Oct 11, 2012

My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 Two Wired Routers In Non-standard Hookup

Sep 14, 2011

I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off).  All computers and other devices connected to it are manually IP configured.  I desire to add a device that cannot be manually configured, and needs DHCP.  I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network).  The new device needs two-way internet access, but doesn't care if it sees any other current network devices.  I've tried several configurations, none seem to work.

View 3 Replies View Related

Linksys Wired Router :: BEFSR81 Keeps Losing Wired Connection To WAP54G?

Apr 11, 2012

I have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81.  I'm not sure if this is an issue with the WAP or the router.
 
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time.  I used to have the power settings such that it didn't power down completely even after a long time.  With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died.  The wireless link would report that it had a solid connection, but I couldn't connect to anything.  Power cycling the WAP always fixed this.
 
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours.   Now, it seems I can't even go one day without losing my connection.
 
I am running the latest frimware in the WAP, and the router is version 3.1.  I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen.  I know from past experience that I will have to power cycle it to get it to talk to me again. 
 
In any event, it seems like the router connection to the WAP is timing out.  I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.

View 3 Replies View Related

Linksys Wired Router :: BEFSR41 - Convert Wired Router To Hub?

Jun 16, 2011

I have an old BEFSR41 ver. 2 wired outer that I'd like to use with a motorola modem/router as a hub.  Is this doable?

View 2 Replies View Related

Linksys Wireless Router :: Can't Create Share Using Storage On E3000

Feb 16, 2012

I have a Maxtor 160Gb external HDD and want to use it as a network drive.So I go to the routers login page and choose for storage to set it up. I did this once and because I wanted to change a few things I deleted the share and changed the users and usergroup that I've made.Now I can't created a share anymore, also tried another disk(flashdrive) nothing seems to work.The only thing I didn't do is reset to factory default, but that's the last thing I want to do.I use the E3000 router with firmware 1.0.04

View 2 Replies View Related

Linksys Wireless Router :: E4200 - Create Two Partitions On HDD (NTFS And HFS+)

Mar 29, 2012

I have at home a mixed platform (Win + OSX and in the future Linux) and the question is: It is possible to create two partitions on the HDD (NTFS and HFS+) and to use the second to backup a Mac computer (LAN connected) via Time Machine?The second question is related to HDD itself, a Lacie Box fitted with Seagate Barracuda Green 2T: The activation of the HDD sleep mode depends on the HDD itself or on the E4200 USB output (feature)?

View 9 Replies View Related

Linksys Wireless Router :: E4200v2 Cannot Create Storage Share

Dec 27, 2011

Just bought router and installed.  I cannot create share in Storage settings in Advanced settings.  I hit Create Share and it brings up the dialog box where I enter the display name.  Share entire partition is checked already.  I save settings and I see the box going to the form where you assign the Group roles, but then the box disappears and closes.  All I see is the original Storage setting page with the Create Share button still there.I tried this on Win 7 using both IE8 and Chrome browsers.

View 4 Replies View Related

Linksys Wireless Router :: Create Second Wifi Network With Wrt54gl?

Apr 3, 2013

I have DSL with a Comtrend router/wifi (WIFI1).  I would like to connect the WRT54GL to the physical network and have it create a separate wifi network (WIFI2), so my laptop will connect to WIFI2, get passed to the LAN and on to the Internet.  Cant make this work - tried setting up the WRT for DHCP server, DHCP pass through (to the comtrend), and the best I can do is get connected to WIFI2 and have access to the LAN but not the Internet. Ultimately I want to put a high gain antenna on the WRT to make it reach another building about 400' away and do away with comtrends horrible WIFI, but I cant get to first base.

View 3 Replies View Related

Linksys Wireless Router :: WRT610N - What Needs To Be Done In Settings To Create VPN Server

Jan 24, 2012

We have a WRT610N wireless router in our office.we want to setup VPN server through a static ip.we dont know what needs to be done in the router settings to create a VPN server. (necessary port forwarding etc)??

View 8 Replies View Related

Linksys Wireless Router :: E3000 - Create Share Windows Is Not Working

Feb 17, 2012

i used to have everything setup properly, Upnp (streaming from PS3), FTP server, Public drive. Everything was working perfect. One day, my drive stopped responsing, and because I had a Security IP camera uploading pictures on it, I thought it was full. The partition was corrupted so I formated the drive. Since then, whatever disk I plug to the router, the "create share" window is not working properly.

View 2 Replies View Related

Linksys Wireless Router :: WRT54G - Create New User ID / Password For Security?

Jul 15, 2012

Time Warner used remote access to get into my wrt54g system and create a new user id/password for security.  As a result, my hp printer will no longer communicate with my computer.  HP says to hook up a usb from router to printer, but there's no usb port on the wrt model I own. I hooked up a usb from computer to printer but it did nada...

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved