Linksys Wired Router :: GRE Internet Protocol 47 Not Getting Through RVS4000
Jun 23, 2011
I have a PPTP VPN server (WIndows 2008 R2) sitting behind an RVS4000, I have port forwarding for 1732 on and the client's (Windows 7) can reach the VPN server but cannot complete the connection due to an 806 error, which is GRE traffic related. I have PPTP passthrough on and have also created a ACL entry for PPTP traffic. I've seen many posts on this topic over several years with no solutions, and I do have the latest firmware (Version:V1.3.3.5). This is also definetely router related as I have absolutley no problem connecting when I point directly to the VPN server by internal IP address.
View 1 Replies
ADVERTISEMENT
Mar 10, 2013
I am trying to configure my RVS4000 to create my church's small network. I want to connect my internet DSL router on the WAN port and also segment my network with VLANs on the 4 LAN ports. I have port 4 connected to a wireless access point which is in VLAN1 for an open wireless network for any church member to access the internet through. I have a church server, printer and second access point on ports 1-3 in VLAN 34. All ports are untagged. I want the devices on VLAN34 which need confidentiality to be secure from the devices connecting to the internet from VLAN1 for open access but both VLANs need access to the internet..
My open wireless AP in VLAN1 has access to the internet on the WAN port.None of my devices in VLAN34 have access to the internet. I have tried using inter-VLAN routing but that made operation worse so I disabled it.
View 1 Replies
View Related
Dec 20, 2008
I just installed an RVS4000 router for a SOHO. I have no problem getting out to the internet so access from LAN -> WAN is working fine. The problem is with VPN access from the WAN.I created a VPN account and set up QuickVPN on a PC making sure I imported the certificate. I can connect to the router with no problem and I can even connect to the routers web admin page.But that's where it ends. I cannot connect in any way, shape, or form to PCs on the LAN through the VPN. I can't even ping them.Am I missing something in the setup of the router?
This is the only reason I bought this router as the old one was working fine. How to fix getting through the router to connect to the computers on the LAN.
View 9 Replies
View Related
Feb 11, 2011
after using BEFSR41 for a long time without any problems, I decided to buy a new router RVS4000 to be able to have gigabit connections.
The problem is when I download a youtube video or I use VPN or even a desktop remote access, it always disconnect. I've seen many and many posts on this forum of people having this problem, I decided to try what you suggested to them:
- Changed the MTU to 1492
- Disabled IPS
- Disabled Firewall
- A couple of other things
- I already have the latest firmware
... and i've done some other tests in my side but nothing worked so far, just like for those who had this problem. I strongly think it's a problem on the router and not a problem from the user.
View 1 Replies
View Related
Jan 24, 2011
I have an RVS4000 located at my office. A user of mine also has one at their house. We have created an IPSec Tunnel between the 2 of them and have them successfully communicating between the 2 networks with no problem.
The problem I have is if I make a change on their end and the router needs to reboot to apply the changes, the WAN port never renews it's DHCP address. The end user must unplug the unit, plug it back in and then the system comes back up with the correct WAN DHCP address, and the tunnel is connected automatically.
I beleive they have the newest firmware (2.0.0.3) but I cannot confirm that right now as the unit is down. I bought the 2 of them at the same time - my unit at the office has the 2.0.0.3 firmware so I am assuming the users does as well.
View 1 Replies
View Related
Mar 14, 2011
I have successfully configured my Cisco RVS4000 for VPN Access, and Installed QuckVPN on my client machine. I can connect using QuickVPN no problem, but I cant access anything on my network. When I try pinging any of my servers I am unable to do so. I can ping my gateway thats about it.
View 1 Replies
View Related
Jan 24, 2013
We share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode". Therefore not acting as DHCP.Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B.Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
View 1 Replies
View Related
Apr 21, 2011
I've looked through the documentation that came with the router and there is no instructions on how to configure the 4000 to accept remote clients and access the local network. What the configurations are so a client can launch the vpn client, login, and remote desktop to their local workstations in the office? I don't have any tunnels or connections setup with other offices, just a simple client connection.Also, will the rvs4000 work with Cisco VPN client (comes with higher end appliances)?
View 1 Replies
View Related
Apr 27, 2008
How to setup quickvpn to work with RVS4000.
View 9 Replies
View Related
Mar 14, 2008
Just purchased a RVS4000. How to be successfully able to VPN into this device from os/x? If so what software / settings required.
View 6 Replies
View Related
Mar 3, 2011
I have RVS4000 v02 and created 3 VLANs - 192.168.70.0/24, 192.168.80.0/24, and 192.168.90.0/24 . I tired to created IP based access list to deny network 192.168.80.0/24 and 192.168.90.0/24 to have access to 192.168.70.0/24; and deny 192.168.90.0/24 to access 192.168.80.0/24.
MY ACCESS LIST from RVS4000
Deny All Protocol LAN 192.168.80.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.80.0/255.255.255.0 Any Time Every Day
Allow All Service LAN ANY ANY Any Time Every Day
Allow All Service WAN ANY ANY Any Time Every Day
* all access list is enabled.Both 192.168.80.0 and 192.168.90.0 network can still reach 192.168.70.0 network.
View 1 Replies
View Related
May 31, 2012
I am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
View 1 Replies
View Related
Feb 2, 2012
I connect to my RVS4000 VPN router using QuickVPN. Very useful.
Sometimes I am not near my laptop and need to check data.
Is there a QuickVPN or compatible client for a BlackBerry Torch 9850, even if it's only functional when connected to WiFi?
View 1 Replies
View Related
Apr 30, 2013
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies
View Related
Mar 15, 2011
Does it support SSL VPN? As I would like to have secure web access without installing other software.
View 1 Replies
View Related
Dec 15, 2011
How to set up RVS4000 QOS settings to work with a VOIP phone system? I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection.
View 1 Replies
View Related
Aug 2, 2011
We have used two Cisco RVS4000 to create the IPSec VPN between the main office and the branch office. The main office has SBS 2008. There is a Windows Server 2008 as the domain controller in the branch office. One branch office user has a laptop which is not in the domain, but his exchange account is set up in the Outlook. When he connects the laptop to the branch office network, he cannot connect to the exchange server and get the emails. Is there any configuration to set up in the router, server or Outlook?
View 1 Replies
View Related
Mar 16, 2011
I need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies
View Related
Feb 28, 2011
Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies
View Related
Nov 25, 2007
My cable modem works fine when not running through the router. However, when running through the router, the internet won't work.I tried unplugging the power and plugging it back in, as well as holding down the reset button for 30 seconds, but nothing worked.
View 8 Replies
View Related
Mar 2, 2013
I have a WRT54GS router, and starting today I am completely unable to access the internet through it. If I connect my computer directly to my modem, I can access the internet, but if I try to connect through the modem, all I get is "DNS server not responding".I've tried changing the DNS server address on the router configuration page, but it doesn't work.
Here's what my ipconfig /all shows:
C:Windowssystem32>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : HomePCPrimary Dns Suffix . . . . . . . :Node Type . . . . . . . . . . . . : HybridIP Routing Enabled. . . . . . . . : NoWINS Proxy Enabled. . . . . . . . : No
[code]....
View 3 Replies
View Related
Sep 12, 2011
I have a BEFSR41 V2 router connected to a westell c90 modem and my provider is Bellsouth.net (AT&T). I have the modem set to PPPoE and DHCP enabled. I am using the router as a gateway. The router's status page indicates that is communicating with the modem. Release and renew works and I can detect the addresses of the modem. I just can't pull up websites. I am wondering if this router (12 years old) is not compatable with the service.
View 1 Replies
View Related
May 12, 2011
I have 2 PCs and am using a Linksys befsr41 router.The first PC connects fine. The 2nd PC does not find a connection. BTW, when I connect my laptop to the 2nd port, it sees the connection immediately - the lights flash on the ethernet connection. No lights on the 2nd desktop PC.
View 2 Replies
View Related
Nov 1, 2012
I bought a cisco 881 router exactly like the one I had . It was configured the same way but cannot get connected to internet.The new router settings do not have an NAT on it, my IT guy turned it on through the console port and we till cannot get it to work?
View 2 Replies
View Related
Jul 9, 2011
I have a Linksys RPT300 (firmware 3.1.27) which I need to pass magic packets on port 9 to internal computer. on LAN the WOL works perfectly.I have masked my local lan to 255.255.255.128 to be able to broadcast on another subnet address than x.x.x.255 which the web interface dont seem to allow.Local LAN is 192.168.15.x and I have created a port forward on port 9 UDP to local broadcast address wich would then be 192.168.15.127. However nothing comes through and I cant seem to find a setting to enable/disable internet broadcasts. Is there a work around?
View 1 Replies
View Related
May 9, 2011
How to connect two PCs and one DSL router to get on the internet?I am getting IP conflict error on the PC. I can only connect one PC at a time to get to internet.
View 1 Replies
View Related
May 20, 2007
Having a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies
View Related
Jul 15, 2011
recently i have updated my firmware, once it said update complete, my internet shut down. I can get on the internet now, but i cant use my router. I have to run my ethernet through my modem now. I have tried resetting it many many times.
View 6 Replies
View Related
Mar 10, 2011
I have an RV042 Router and did a one-to-one NAT mapping for my server using an additional external IP I received from byt ISP, pointing to machine 192.168.2.5. I am now successfully able to access the machine via the external IP without issue, however the server is no longer able to ping any external IPs?
the machine has been assigned a static IP of 192.168.2.5 and static DNS servers.
View 1 Replies
View Related
Apr 20, 2013
I have a BEFSR41...about 2x a week when connecting to internet I have to pull and replug router in order to get on-line.
View 3 Replies
View Related
Jan 11, 2011
I upgraded the firmware on my BEFS41 v4.3 to the Ver.2.00.4 Build 8, off the cisco website. After I received the successfully upgraded message, I could no longer connect to the internet, nor could I connect to the router's configuration page. I tried to do a few hard resets and connecting it to other computers to see any other computers could connect to it, no luck. I tried connecting one computer just to the router, without the internet plugged in, and tried to ping 192.168.1.1 but I received a "transmit failed, error code 1231." Is there anyway I can access this and change the firmware, or am I screwed?
View 3 Replies
View Related
May 26, 2012
DSL modem works fine when connected directly to computer. No internet output from WRT54G wired or wireless, but wireless network is recognized by computer, just no internet. I did a reset and installed the latest firmware, then I ran thru the setup CD that came withe the router, and the internet test said no internet connection was available. Cables are fine, connector innards look clean.
View 4 Replies
View Related
Jul 14, 2011
I have a RV082 Linksys router and at the moment it is slowing down my internet connection by a significant amount. With the router, I get about 3 Mbps and with a modem directly connected to my computer I get about 24 Mbps. Before with the router I used to get 15 Mbps, which is understandable because it is connected to 4 computers total. Maybe my setup has something to do with it. I got a cable that is connected to a modem, the modem is connected to the router, from which one port is connected to a computer, and another is used to connect to a Netgear switch, which in turn is connected to 3 more computers.
Everything was fine until I went on a trip and wasn't home for about 2 weeks, and when I came back, this happened. I tried restarting the modem, the router and all to no avail. I also tried to do a factory reset on the router and again got slow speeds.
View 1 Replies
View Related
