Linksys Wired Router :: How To Setup VLANS On RVS4000
Jan 24, 2013
We share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode". Therefore not acting as DHCP.Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B.Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
View 1 Replies
ADVERTISEMENT
Mar 10, 2013
I am trying to configure my RVS4000 to create my church's small network. I want to connect my internet DSL router on the WAN port and also segment my network with VLANs on the 4 LAN ports. I have port 4 connected to a wireless access point which is in VLAN1 for an open wireless network for any church member to access the internet through. I have a church server, printer and second access point on ports 1-3 in VLAN 34. All ports are untagged. I want the devices on VLAN34 which need confidentiality to be secure from the devices connecting to the internet from VLAN1 for open access but both VLANs need access to the internet..
My open wireless AP in VLAN1 has access to the internet on the WAN port.None of my devices in VLAN34 have access to the internet. I have tried using inter-VLAN routing but that made operation worse so I disabled it.
View 1 Replies
View Related
Dec 20, 2008
I just installed an RVS4000 router for a SOHO. I have no problem getting out to the internet so access from LAN -> WAN is working fine. The problem is with VPN access from the WAN.I created a VPN account and set up QuickVPN on a PC making sure I imported the certificate. I can connect to the router with no problem and I can even connect to the routers web admin page.But that's where it ends. I cannot connect in any way, shape, or form to PCs on the LAN through the VPN. I can't even ping them.Am I missing something in the setup of the router?
This is the only reason I bought this router as the old one was working fine. How to fix getting through the router to connect to the computers on the LAN.
View 9 Replies
View Related
Feb 11, 2011
after using BEFSR41 for a long time without any problems, I decided to buy a new router RVS4000 to be able to have gigabit connections.
The problem is when I download a youtube video or I use VPN or even a desktop remote access, it always disconnect. I've seen many and many posts on this forum of people having this problem, I decided to try what you suggested to them:
- Changed the MTU to 1492
- Disabled IPS
- Disabled Firewall
- A couple of other things
- I already have the latest firmware
... and i've done some other tests in my side but nothing worked so far, just like for those who had this problem. I strongly think it's a problem on the router and not a problem from the user.
View 1 Replies
View Related
Jan 24, 2011
I have an RVS4000 located at my office. A user of mine also has one at their house. We have created an IPSec Tunnel between the 2 of them and have them successfully communicating between the 2 networks with no problem.
The problem I have is if I make a change on their end and the router needs to reboot to apply the changes, the WAN port never renews it's DHCP address. The end user must unplug the unit, plug it back in and then the system comes back up with the correct WAN DHCP address, and the tunnel is connected automatically.
I beleive they have the newest firmware (2.0.0.3) but I cannot confirm that right now as the unit is down. I bought the 2 of them at the same time - my unit at the office has the 2.0.0.3 firmware so I am assuming the users does as well.
View 1 Replies
View Related
Mar 14, 2011
I have successfully configured my Cisco RVS4000 for VPN Access, and Installed QuckVPN on my client machine. I can connect using QuickVPN no problem, but I cant access anything on my network. When I try pinging any of my servers I am unable to do so. I can ping my gateway thats about it.
View 1 Replies
View Related
Jun 23, 2011
I have a PPTP VPN server (WIndows 2008 R2) sitting behind an RVS4000, I have port forwarding for 1732 on and the client's (Windows 7) can reach the VPN server but cannot complete the connection due to an 806 error, which is GRE traffic related. I have PPTP passthrough on and have also created a ACL entry for PPTP traffic. I've seen many posts on this topic over several years with no solutions, and I do have the latest firmware (Version:V1.3.3.5). This is also definetely router related as I have absolutley no problem connecting when I point directly to the VPN server by internal IP address.
View 1 Replies
View Related
Apr 21, 2011
I've looked through the documentation that came with the router and there is no instructions on how to configure the 4000 to accept remote clients and access the local network. What the configurations are so a client can launch the vpn client, login, and remote desktop to their local workstations in the office? I don't have any tunnels or connections setup with other offices, just a simple client connection.Also, will the rvs4000 work with Cisco VPN client (comes with higher end appliances)?
View 1 Replies
View Related
Apr 27, 2008
How to setup quickvpn to work with RVS4000.
View 9 Replies
View Related
Mar 14, 2008
Just purchased a RVS4000. How to be successfully able to VPN into this device from os/x? If so what software / settings required.
View 6 Replies
View Related
Mar 3, 2011
I have RVS4000 v02 and created 3 VLANs - 192.168.70.0/24, 192.168.80.0/24, and 192.168.90.0/24 . I tired to created IP based access list to deny network 192.168.80.0/24 and 192.168.90.0/24 to have access to 192.168.70.0/24; and deny 192.168.90.0/24 to access 192.168.80.0/24.
MY ACCESS LIST from RVS4000
Deny All Protocol LAN 192.168.80.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.80.0/255.255.255.0 Any Time Every Day
Allow All Service LAN ANY ANY Any Time Every Day
Allow All Service WAN ANY ANY Any Time Every Day
* all access list is enabled.Both 192.168.80.0 and 192.168.90.0 network can still reach 192.168.70.0 network.
View 1 Replies
View Related
May 31, 2012
I am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
View 1 Replies
View Related
Feb 2, 2012
I connect to my RVS4000 VPN router using QuickVPN. Very useful.
Sometimes I am not near my laptop and need to check data.
Is there a QuickVPN or compatible client for a BlackBerry Torch 9850, even if it's only functional when connected to WiFi?
View 1 Replies
View Related
Apr 30, 2013
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies
View Related
Mar 15, 2011
Does it support SSL VPN? As I would like to have secure web access without installing other software.
View 1 Replies
View Related
Dec 15, 2011
How to set up RVS4000 QOS settings to work with a VOIP phone system? I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection.
View 1 Replies
View Related
Aug 2, 2011
We have used two Cisco RVS4000 to create the IPSec VPN between the main office and the branch office. The main office has SBS 2008. There is a Windows Server 2008 as the domain controller in the branch office. One branch office user has a laptop which is not in the domain, but his exchange account is set up in the Outlook. When he connects the laptop to the branch office network, he cannot connect to the exchange server and get the emails. Is there any configuration to set up in the router, server or Outlook?
View 1 Replies
View Related
Mar 16, 2011
I need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies
View Related
Feb 28, 2011
Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies
View Related
Mar 16, 2011
We have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?
View 1 Replies
View Related
Dec 19, 2012
How to setup the quickvpn.... I am getting the message Servers certificate doesnt exist on your local computer..... and the the window fail to establish the connection
View 1 Replies
View Related
May 1, 2012
I'm trying to setup 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24.I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 1 Replies
View Related
Nov 24, 2009
I have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
View 2 Replies
View Related
Nov 5, 2009
I have two PCs hooked up to the same router, a BEFSR41. Both connect to the internet fine. One can access the router setup/admin page fine. On the other one, though, the router asks for a user name and p/w, but the setup screen never loads. I get the eternal "Loading" message but it never gets there.
[code]....
View 8 Replies
View Related
Feb 23, 2011
I'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.
View 1 Replies
View Related
Sep 1, 2011
On a BEFVP41, I disabled snmp for testing (because it was sending some strange alarms), and now I can't login to the web setup pages. The username and password no longer work. I thought maybe it reset itself to default (blank/admin) but it didn't.
View 1 Replies
View Related
Dec 2, 2011
I've brought a SG300-10 switch and would like to connect it to an Apple Time Capsule (as the base station of my wireless network), Apple Airport Extreme (to extend my wireless network) and 3 x NAS. What is the best way to connect?
Internet > SG300 > Apple TC + NAS x 4 + Apple Airport Extreme (to extended my wireless network) + Mac Pro/iMac'sInternet > Apple TC > SG300 > NAS x 4 (connect to the SG300) + Apple Airport Extreme (to extended my wireless network) + Mac Pro/iMac'sI need the SG300 because the Apple TC doesn't have enough network ports to cennect all my other devices.
View 1 Replies
View Related
Jan 22, 2013
Recently lost the setup for my newly installed ea6500 for no apparent reason. had to restart from the ground.I have the latest upgrade but wonder about the differences between the linksys coonect to the online version vs stand along versions. DO nor like expensive software that losses its setup for no good reason.I also irritated that I am unable to access my cable box. I own it and cable box and lynkiys has no right to block me from it. 192.168.100.1. I was able to accessed it with my Belkin router and I should be able to access with this expensive ea6500 box!!
We NEED a non-gui version. The gui is great for simple networks and people who do not want to know anything about their network. it's ment to be use to deliver additional services to us at a cost. duplicated or generates random users with ip or mac addresses complicating the parental control.
View 1 Replies
View Related
Aug 11, 2011
I have just setup a E2000 at home. All the wireless connections work and also my NAS server who i wired. But when i try to setup my wired media server it will not connect.
View 6 Replies
View Related
Jan 10, 2012
I have the Linksys BEFSX41 wired Firewall router. My ISP is Verizon DSL. The DSL modem is a Westell 6100G. I have the wall phone line connected to my modem. The output of the modem is going to the input of my Linksys router. I have two computers connected to the router outputs. In order for me to see the output or configuration of my Westall modem, I have to go http://192.168.1.1. In order for me to see the configuration of my Linksys router, I have to enter http://10.10.10.1. When I look at the instructions for setting up and configuring my Linksys router, it never mentions the above 10.10.10.1 address, but instead it tells me to enter the 192.168.1.1 address. I have never done this because when I powered both units for the first time, and it worked, I noticed then that my Linksys address was the 10.10.10.1. Why is it then that none of the settings or instructions for the Linksys router never mention to enter the 10.10.10.1 address as oppose to the one the do call out to enter which is the address for the Westell modem? What would happen if both addresses on both devices were the same?
View 2 Replies
View Related
Mar 9, 2013
I am trying to configure my RVS4000 to create my church's small network. I want to connect my internet DSL router on the WAN port and also segment my network with VLANs on the 4 LAN ports. I have port 4 connected to a wireless access point which is in VLAN1 for an open wireless network for any church member to access the internet through. I have a church server, printer and second access point on ports 1-3 in VLAN 34. All ports are untagged. I want the devices on VLAN34 which need confidentiality to be secure from the devices connecting to the internet from VLAN1 for open access but both VLANs need access to the internet..
My open wireless AP in VLAN1 has access to the internet on the WAN port.
None of my devices in VLAN34 have access to the internet. I have tried using inter-VLAN routing but that made operation worse so I disabled it.
View 1 Replies
View Related
Jan 23, 2013
I live in a two family residential house and we share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode". Therefore not acting as DHCP. Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B. Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
What I have unsuccessfully tried to achieve and am currently trying to separate the networks so that both families can access internett, but at the same time it must be impossible to access VLAN1(Family A) from VLAN2(Family B) vice versa. Meaning no communication between the two families through the local network.
I have tried different options but I am not sure how to deal with trunk, tagged, untagged etc. etc. etc. It seems every time I manage to create two different networks there is still accessability/communication between the two VLANs and everytime I manage to give out different IP adresses to different ports i.e. 192.168.10.xx and 192.168.2.xx it is still possible to communicate. What also usually happens is that the internetconnection is severed at the same time.
View 15 Replies
View Related
Nov 7, 2011
I finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies
View Related
