Linksys Wired Router :: RT341P2 Can't Use Voip Providers

Mar 10, 2012

I buy new Linksys RT341P2 router with Linksys - Firmware Version: 1.30.01. My voice ports are locked, and i can`t use voip providers. How to unlock and what i need to do?

View 1 Replies


ADVERTISEMENT

Linksys Wired Router :: RV082 Load Balancer Between 2 Providers

Feb 25, 2011

I have got Linksys RV082 in my home network to use it as load balancer between 2 providers.Is it possible to make some customisation in scenarioses and logging system? As I understand the device is based on some Linux core and Linux infracrtucture. So it must me available in sources... How I may get this kind of access? I want to get ssh/telnet or other raw access to installed on the device OS and manual control it, treat around web-UI. How may I do it?

View 1 Replies View Related

Linksys Wired Router :: VOIP Dropping Connection 2-3x Per Day

Feb 13, 2013

I have a strong internet signal with good SNR coming out of my cable modem, then a nice short 3ft cable going to my linksys VOIP router (I think it's a SPA 2102). Whether I have anything downstream plugged in or not, the "phone" light on the VOIP router goes off every once in a while and when I check I find that I've lost both dial tone and Internet - basically everything downstream of the VOIP router. Have tried every variation on configuration you can imagine (feeding just one phone, feeding the entire phone wiring to the house, nothing at all plugged into the phone jack, no computers downstream plugged in, replaced all the cables, ...). I've replaced BOTH the cable modem and the linksys VOIP router and the problem continues. My cable company says my signal is fine. They suggested a signal amplifier but the coax comes straight to the modem, no splitter, and I'm always seeing 6-7dBmV. My phone company says their router must be losing signal upstream and refusing to reconnect, especially now that we've tried replacing their VOIP router with no change. Any chance I got two 'bad' routers in a row? Not sure what they did for setup parameters. I'm not particularly tech-savvy but have read a lot since seeing these issues, have run my own ping and tracert checks and everything seems to be wonderful... but then most of the time everything IS fine. When I have phone it's crystal clear and when I have internet it's nice and fast. I sometimes go 24hrs or so without a drop, but other times I'm resetting 2-3x in a couple of hours. All I do is power off the VOIP router and back on and everything is fine, for a while. After first getting VOIP things were fine for 4-6 weeks.

View 1 Replies View Related

Linksys Wired Router :: RVS 4000 - Voip PBX Server Is Dropping Calls

Jul 8, 2008

I recently purchased a rvs 4000 wired linksys router for my business.  Everything works great with the exception of my VOIP PBX server.  I can receive a call and make a call one at a time.  If a second line rings in and is picked up the first call and the second go dead air.  I am sure that it is a security setting somewhere that I just can't seem to figure out.  I sure would like to get some direction on this.

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 Fed From SPA2102 VoIP Phone Adapter

Oct 15, 2011

A broadband cable modem is connected to the input of a new BEFSR41 4-port router.  The router feeds 4 computers (a newer "primary" PC, and 3 secondary "old goats" that I use to print online grocery coupons).  The 4 PC's are networked to share a common printer, a single directory on the "primary" PC, and using a 4-port KVM switch - I switch a single keyboard and mouse to whichever PC that I am using at the time. 

View 1 Replies View Related

Linksys Wired Router :: How To Set Up RVS4000 QOS Settings To Work With VOIP Phone System

Dec 15, 2011

How to set up RVS4000 QOS settings to work with a VOIP phone system?  I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection. 

View 1 Replies View Related

Linksys Wireless Router :: Wrt54gx - How To Change Internet Providers

Apr 5, 2012

have a wrt54gx and changed internet provider from cable to dsl. Can you let me know how to do this? I have a printer routed through the router.

View 1 Replies View Related

Linksys Wireless Router :: Any Free DDNS Providers That Can Be Used With EA6500

Dec 20, 2012

Is there any free DDNS providers that can be used with a EA6500 ?

View 3 Replies View Related

VoIP With No Wired Ethernet Port Access

Jun 7, 2011

I have a VoIP phone that requires connection to a wired Ethernet port. I won't have access to the Ethernet port from my new apartment and need to connect over WiFi accessed by my computer. Is there a way to run the VoIP phone over that connection?

View 1 Replies View Related

Wireless :: VOIP Phone With LINKSYS Router

Mar 11, 2011

I have a VOIP WiFi phone (MIC505W) I have configure it according to the user manual.I get access to WiFi, but when I dial a number I get busy signal with the message "disconnet".

View 3 Replies View Related

Cisco Switching/Routing :: Default Gateway Of VOICE Providers 2600 Router

May 21, 2012

We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too. 

At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites. 
Testing
 
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps? 

View 15 Replies View Related

Linksys Wired Router :: EA4500 - Wired Connections Have Long Ping Times

Sep 23, 2012

I purchased and set-up the EA4500 on Thursday.  Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues.  Connected directly to modem I get normal ping times on whichever computer is connected.  When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms.  They are all over the place 30ms (I can live with that), up to the 900's.  I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference.  I did end up doing a hard reset on the router last night after I lost tech support.  We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
 
It was so slow on my work computer, a pint to yahoo timed out.  The computers connecting to router are
 
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP

View 5 Replies View Related

Linksys Wired Router :: E2000 - Security Wired Ethernet Connections

Sep 19, 2011

I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive.  I am planning to allow a tenant in another building connect via an ethernet cable connected to my router.  Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router?  I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.

View 1 Replies View Related

Linksys Wired Router :: E4200 No Longer Accepts Wired Connections?

Oct 11, 2012

My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 Two Wired Routers In Non-standard Hookup

Sep 14, 2011

I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off).  All computers and other devices connected to it are manually IP configured.  I desire to add a device that cannot be manually configured, and needs DHCP.  I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network).  The new device needs two-way internet access, but doesn't care if it sees any other current network devices.  I've tried several configurations, none seem to work.

View 3 Replies View Related

Linksys Wired Router :: BEFSR81 Keeps Losing Wired Connection To WAP54G?

Apr 11, 2012

I have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81.  I'm not sure if this is an issue with the WAP or the router.
 
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time.  I used to have the power settings such that it didn't power down completely even after a long time.  With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died.  The wireless link would report that it had a solid connection, but I couldn't connect to anything.  Power cycling the WAP always fixed this.
 
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours.   Now, it seems I can't even go one day without losing my connection.
 
I am running the latest frimware in the WAP, and the router is version 3.1.  I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen.  I know from past experience that I will have to power cycle it to get it to talk to me again. 
 
In any event, it seems like the router connection to the WAP is timing out.  I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.

View 3 Replies View Related

Linksys Wireless Router :: Why Does E4200v2 Not Detect VOIP ATA

Jan 11, 2013

I have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not.  The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.

View 1 Replies View Related

Linksys Wireless Router :: VOIP Does Not Work Via E4200?

Jul 25, 2011

I have a new Polycom Soundpoint IP550 VOIP phone that was not connecting via my old WRT54GS router.  I purchased a new router, the E4200, thinking it was just the age of my original router.  It also will not allow the VOIP traffic through.  I can connect the VOIP phone directly to my CenturyLink modem and it works.  But when I connect it back to the router it stops.  
 
I contacted Cisco support and they had me upgrade the firmware to 1.0.02 build 13  May 24, 2011 version.  Also adjusted down the MTU to 1364. That still did not work so they told me to take the router back to the store.  I have not done that yet as I want to ensure that the router is really broken and not that I am missing a setting.  The tech said that I should be able to plug the VOIP phone into the router and make NO additional changes.

View 1 Replies View Related

Linksys Wireless Router :: Configuring E4200 For VOIP Prioritization

Sep 8, 2011

How do I configure E4200 for VOIP priority. My vonage adapter is connected to the router by Ethernet.Also I want google voice call prioritization.

View 1 Replies View Related

Linksys Wireless Router :: Tmobile WRTU54G-TM Connection To VOIP Service?

Jan 18, 2012

A client is using Tmobile VOIP using the aforementioned WRTU54G-TM 2-line VOIP wireless router with 4-port hub.  What they would like to do is to place this in their network and NOT have it change (route) the network addresses being assigned to devices 'behind' this router so even their wireless devices are all "on the same network" as the wired devices BEFORE this unit,  In essence, preserve the same 'network and subnet mask' that is being issued by their DSL router via it's integrated DHCP server. ... Rather like operating this unit like an 'access point' instead of a router.Under most circumstances, I might try to assign this router a static IP outside the scope of the DHCP range the DSL router would supply, then plug the (gigabit) Ethernet network cable into one of the 4 Ethernet ports on the rear of this router - but apparently this does not 'facilitate' a connection to Tmobile's VOIP service.When attempting to do this, the connected telephone devices do not get a phone line connection and the status light(s) that normally indicate proper operation do not illuminate.

View 3 Replies View Related

Linksys Wireless Router :: E3000 And Gigaset C410 VoIP Connection

Jan 25, 2012

I have installed the LinkSys E3000 Router, but I am still struggling because the device Gigaset Siemens C410 (that is the VoIP base) does not work.Before the E3000 I had an WRT160Nv2, with this router the Voip Devise works properly. If I link the WRT160Nv2 to the E3000 and the VoIp device to the WRT160Nv2 it works.

View 1 Replies View Related

Linksys Wireless Router :: 4200v1 Set Up With Same Great Quality Voip While Uploading / Downloading

Mar 21, 2013

I use in my network Linksys 4200v1 (newest firmware) and Sipura SPA 3000 ( 3.1.20(GW)firmware) and SPA 122 (1.1.0(011) software version as my phone adapters.My voip phones  are working great until I start to download or upload some files, watching on-line tv.How and where should I set up above routers to have the same great quality voip while uploading and downloading at the same time?

View 4 Replies View Related

Linksys Wireless Router :: WRT54GL Versus Magic Jack VoIP Telephone

Feb 17, 2010

I got my WRT54GL v1.1 yesterday and connected it to my pc [wired] and netbook [wireless]. I thought all was well until I noticed that my Magic Jack VoIP telephone began dropping calls after about 1 minute. My first course of action was to disable SPI firewall in router and reboot. That had no affect on the situation, then I noticed that my send light on my cale modem [ no manufacturer listed on unit] was not blinking as it has done before the router installation. I reverted to my cable modem to pc only set up and my Magic Jack worked just fine. I need to use the router for wireless, so I need to find a solution to this problem. I took a look at my firmware version and saw that it was not current, but I wanted to bring my problem here for a possible solution be for I flashed new firmware.

View 9 Replies View Related

Linksys Wired Router :: BEFSR41 - Convert Wired Router To Hub?

Jun 16, 2011

I have an old BEFSR41 ver. 2 wired outer that I'd like to use with a motorola modem/router as a hub.  Is this doable?

View 2 Replies View Related

Any MPLS Providers

Nov 7, 2012

We're looking at rolling out MPLS between each of our sites. probably more soon.Do you guys have favorite MPLS providers? How have your experiences been?

View 10 Replies View Related

Broadband :: Can Have 2 Internet Service Providers

Jun 16, 2011

Can I have 2 Internet providers?I've been with Orange broadband for a few months and it's been unusably slow, so we're cancelling the contract and changing to Sky. Orange are making us trouble-shoot before this can happen, so the preference would be to install Sky, leave the Orange router unplugged and ignore it until the contract ends. Is this realistic? I know both couldn't use the line at the same time, but could we just unplug our Orange router or would it create slow down or not work at all?

View 2 Replies View Related

How Do The Tier 1 Network Providers Gets Bandwidth

Feb 13, 2013

Tier 2 and tier 3 purchase from tier 1 provider ,but how is bandwidth produced i mean how tier 1 provider gets bandwidth. and why tier 1 doesn't have to pay.

View 7 Replies View Related

Can't Validate The Winsock Base Providers - 2

Feb 12, 2012

I received a message stating: Info-error attempting to validate the winsock base providers:2 Error- Not all base service provider entries could be found in winsock catalog. A reset is needed. Info- Redirecting user to support call I did the reset in command prompt as I read you told other people with this problem to do. But I still keep getting these messages.This is my sister's Dell Latitude 620.I used AVG and I think pc is clean. When I try to connect to a website page states that Internet Explorer cannot display the webpage.

View 10 Replies View Related

D-Link DIR-655 :: Bridging Using Isp Providers Modem

Jul 27, 2011

I have some network experience but not a lot so here is my problem.I have a zyxel q1000z from qwest that i want to bridge to my dir 655.I go through the settings to put their router/modem to bridge mode. This units default ip is the same as tslinkink, 192.168.0.1 so i change the d-link to 192.168.0.2. I then go into the D-link and enter my isp's pppoe settings and password. I reboot when i am done but can't connect to the internet.It shows connected but that's it. I want to use the d-link as the only router as the zyxel has very few settings and has slowed down my netflix.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8961NB / How To Add Other DDNS Providers

Jan 12, 2013

Region : Germany
Model : TD-W8961NB
Hardware Version : V1
Firmware Version : 1.0.0 Build 110707 Rel.32779
ISP : DTAG

would it be possible to add other DDNS providers to the router menu?E.g. I use dnsomatic.com as DDNS service (pretty much the same syntax/protocol as DynDNS, but free and more flexible).

View 2 Replies View Related

Dell :: D630 Broadband Facility Limited To Certain Service Providers?

Apr 27, 2013

is the dell d630 broadband facility limited to certain service providers coz im inserting my Econet simcard bt it still says no device detected

View 3 Replies View Related

Linksys Cable / DSL :: WAG160N Doesn't Work With VOIP Phones

May 21, 2011

I purchased Linksys WAG160N (from a store)  and I also have 7 Linksys SPA962 VOIP phones provided by MyNetPhone with service included. All tests we found out that this modem doesn't work with this VOIP phones. Somehow probably doesn't give access to MyNetPhone servers to get connection with this phones.I purchased an other one from DLINK and works perfect?

View 1 Replies View Related

Linksys PAP-2T Voip Adapter / Connect 2-3 Devices To An Existing Wireless Network

Aug 18, 2012

I need to connect a pc desktop and A linksys PAP-2T voip adapter to an existing wireless network(home network).

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved