Linksys Wired Router :: RV082 - Can The SNMP Trap To Field

Jan 25, 2011

I use SNMP and I dont have access to a router to test.Can the SNMP Trap to: Field in the SMNP section be configured for multiple IP addresses.?

View 1 Replies


ADVERTISEMENT

Configure SNP Server For SNMp Trap?

Jul 1, 2011

send me step by step guide of how to configure SNP server for SNMp trap

View 2 Replies View Related

Linksys Wired Router :: RV082 - Set Up Dual WAN?

May 15, 2009

I am trying to set up a dual WAN on my RV082 - I have Verizon DSL on WAN1 and I am trying to establish Time Warner Road Runner on WAN2 as a backup in case DSL goes out on WAN1.I cannot get the router to recognize both connections at the same time.  I have power cycled everything, the router is only picking up one internet signal at a time.

View 3 Replies View Related

Linksys Wired Router :: RV082 - Make It Or An IP Go Through Certain WAN?

Nov 10, 2011

How can I make a device or an IP go through a certain WAN? Basically I want to make the PC I use on the network go through WAN2, I have tried everything but I am really stumped on how to do this, my Firmware Version: v4.0.2.08-tm

View 1 Replies View Related

Linksys Wired Router :: RV082 Cannot Login Via LAN

Mar 15, 2012

I am using RV082 V3 router. After a reset of the router I have access via both LAN and WAN for some period of time (not yet known)  later that day or the next day when I try to access it via the WAN it sits on "opening page" for a while eventually coming up with the login box. After logining in the page only partially loads. (All the settings are shown, but the proper selections are not made.) Internet explorer will then show something like "8 items remaining" in the status bar. If I close and re-open IE I am unable to connect at all. At this point I also cannot login via the LAN. However, internet access appears to be fully function through the router and the router also responds to pings. (I have the latest firmware loaded.) The only resolve I've found is power cycling the unit to regain login access to it. Very irritating, and impossible when not at the physical location.

View 1 Replies View Related

Linksys Wired Router :: RV082 One-To-One Nat Different Ports?

Feb 8, 2011

I am setting up One-To-One NAT to redirect traffic from the internet. We have 5 static public IP addresses, and I set up One-To-One Nat to redirect to local Win servers. One of the servers running Web server and FTP server. For some reason redirection works fine for the Web server, but does not work for FTP server when I try to access them from the internet. FTP server works locally, but my FTP client cannot connect from the Internet. I opened the ports in the firewall, and these ports show as opened when I test them from external servers. What am I missing?

View 1 Replies View Related

Cisco :: LMS 4.1 Taking SNMP Trap To Email Alarms

Feb 1, 2012

Upgraded LMS to 4.1. Yep basically reinstalled. However I can't remember how I did a couple of thing on the original system.
 
I am trying to take the traps from the Cisco equipment to the LMS and generate e-mail.  How do I take the incoming traps (Crit and Warning) and send an e-mail alarm.  I'll plan to control what to trap on at the Cisco Equipment.
 
SNMP trap is set from a fan fault, the Cisco send a trap to the LMS.  Now I want take that trap and forward via an email. 
 
I have been reading the admin documentation on "Notification and Action Setting".  I see how to take the Cisco LMS created trap and email alarm.  (In this case I need a specific trap that LMS did not have.)  I see how to take Cisco Traps and resend them to other NMS.

View 1 Replies View Related

Linksys Wired Router :: How To Setup RV082 QuickVPN

Dec 19, 2012

How to setup the quickvpn.... I am getting the message Servers certificate doesnt exist on your local computer..... and the the window fail to establish the connection

View 1 Replies View Related

Linksys Wired Router :: RV082 - Speed Drops To Between 2-3mb / Sec

Oct 25, 2007

Networking isn't my strongest computer subject area, but I know I'm having a performance problem with my RV082 router. When I direct connect my PC to my cable modem, I can get very near the 7mb/sec rate advertised by my ISP. When I connect the modem to this router, then connect to the pc to the router, the speed drops to between 2-3mb/sec. All tests performed several time using dslreport.com speed test website. The result is very repeatable, so I figure it has to be some delay introduced by the router. I can't see to find any place in the router configuration to do performance tuning. I'm not using any firewall rules except for the default rules. Why I'm seeing a greater than 50% decrease in internet throughput using this router?

View 8 Replies View Related

Linksys Wired Router :: RV082 Stopping Communication

Feb 26, 2013

I have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.

View 1 Replies View Related

Linksys Wired Router :: Rv082 - Two Ranges Of IPs For DMZ Configuration

Apr 28, 2013

we have a RV082 and have the DMZ option enable for a range of IPs within the same sub-net of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same sub-net of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ.
 
Our ISP internet feed plugs into the RV082 WAN port and we have a switch plugged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port.
 
My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port, how I can do this without one-to-one NAT or port port forwarding? The device I am deploying needs to be at the border of our network (like in the DMZ) and have some ability to talk to a device on our LAN.  

View 1 Replies View Related

Linksys Wired Router :: Getting RV042 And RV082 Throughput?

Feb 17, 2008

I am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.

View 9 Replies View Related

Linksys Wired Router :: PCI Compliance And SSL Ciphers On RV082?

Mar 22, 2009

I am trying to get our internal network PCI compliant and when I run a network scan from securitymetrics.com I receive the following message about our RV082 router.
 
Synopsis : The remote service supports the use of weak SSL ciphers. Description : The remote host supports the use of SSL ciphers that offer either weak encryption or no encryption at all. See also :[URL]: Reconfigure the affected application if possible to avoid use of weak ciphers. Risk Factor: Medium  / CVSS Base Score : 5.0
  
I have been googling many different search terms for ssl ciphers, rv082, and pci compliance but didn't see any solutions to this.  Any experience with ssl ciphers and how to use more secure ciphers?  I just performed a firmware upgrade to 1.3.98-tm in hopes that it would fix this issue.

View 2 Replies View Related

Cisco :: When Below SNMP Trap Type Triggers From Network Devices

Dec 7, 2012

We are implementing fault management tool and for that we need information such as what type of traps are being triggered by router on what events..currently we have BGP, interface,reachability,h/w,syslog,authfail,config, trap types configured..All these are hitting in our fm tool but I need to know when these traps are being triggered by router.more importantly authfail, config, syslog, bgp.

View 4 Replies View Related

Cisco :: 3750 Sw Is Not Sending SSH Login Failure SNMP Trap

Nov 22, 2011

I want to make my switch send trap when failed SSH login is detected. I found the "login Enhancement" feature and enabled the trap and logging for the failed attempt.
 
3750# sh run | in login
aaa authentication login default local
login delay 1

[Code].....

View 7 Replies View Related

Cisco Firewall :: Configure ASA 5520 To Send SNMP Trap?

Apr 16, 2012

Below is my config for IP SLA.  I would like a SNMP trap to be sent when my primary fails over to my secondary and so on.
 
sla monitor 20
type echo protocol ipIcmpEcho 100.X.X.1 interface INET-FIOS150
num-packets 2

[Code].....

View 4 Replies View Related

Cisco Application :: ACE 4710 Switchover SNMP Trap Notification?

Jun 20, 2012

I am in the process of testing VA5(1.2) version of ACE on ACE4710 appliance.I did redundnacy configuration and it is working fine.I have done the snmp configuration and SNMP trap receiver is able to recieve traps like link up/down, so it proves that SNMP configuration is working fine, but i am not able to generate the SNMP trap notification for "clrRedundancyStateChange".I tried two things:

1) Via CLI, ran the command "ft switchover all" and i could see redundancy state changes.

2) Powered down Active 4710 appliance and standby ACE 4710 appliance taking over as Active.
 
However, none of the above could generate the trap clrRedundancyStateChange. how this trap can be generated? In snmp-server enable traps commands doesn't have any option for enabling FT related traps.

View 1 Replies View Related

Cisco Firewall :: ASA 5510 / SNMP Server To Receive Trap?

Apr 9, 2011

How to prepare my network for snmp,currently i don't have SNMP configured with community,so what is the requirement for that?what server i need to configure in order  to receive SNMP traps coz last time i had issue ,one of my tunnels (terminated on asa 5510) goes down for 2 hours and i didn't realized that

View 7 Replies View Related

Cisco Switching/Routing :: SNMP Trap For Syslog In Nexus 5K

Mar 30, 2013

how to enable snmp traps for syslog message in Cisco Nexus platform ?
 
Mean what would be equivalent CLI for the below
 
"snmp-server enable traps syslog"

View 2 Replies View Related

Cisco Wireless :: 1130 AG - SNMP Trap On AP Max Associations Reached

Feb 21, 2012

I want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap.  We currently use both 1130 AG and 1140-2N in autonomous mode, no controller.  I have found a debug command "debug dot11 station connection failure" and the output of a test AP shows us the fact that the maximum number was reached.  I need to find if it is possible to trap on such information. 

View 1 Replies View Related

Cisco Wireless :: WLC 7.0.98.0 / How To Convert Snmp Trap To Be Syslog Message

Aug 22, 2011

Now I'm trying to write software that get information from Syslog message, but I'm facing with the problem about getting statistic of client de-authenticated in a WLC (Software Version: 7.0.98.0), because I cannot find any log about this information on WLC except only this SNMP trap:
 
Tue Aug 23 09:52:28 2011Client Deauthenticated: MACAddress:00:xx:77:2c:06:db Base Radio MAC:00:xx:5d:0c:fc:30 Slot: 0 User Name: unknown Ip Address: 10.2xx.47.15 Reason:Unspecified ReasonCode: 1
 
So, is there any way that I can configure WLC to convert this SNMP trap to send to Syslog server as a normal Syslog message?

View 2 Replies View Related

Linksys Wired Router :: RV082 And Load Balancing Mode On 2 WAN?

Jul 2, 2007

I have some problem connecting to sites when I'm using the router in Load Balancing mode on the 2 WAN. Looks that when a connection to a site is started with a WAN is not manteined with this one but jump from a wan to the other, causing, in some site like Home Banking to be disconnected every time. I would like to know if it's possible to configure the roouter in Load Balancing but Bindind the source and the destination IP address so the same wan will be used for the entire time this connection is up. In opther words the Load Balancing has a sense beetween connections not beetween the same connection.

View 9 Replies View Related

Linksys Wired Router :: RV082 / NSD Fail Through Radio Link

Sep 27, 2012

I have a Ubiquiti radio link between my DSL modem and RV082 router and although the router log states that it is connected to the static ip address of the modem i get and NSD fail and have no connection.  if I plug the radio link directly into a computer with the static ip I get a connection but the modem has a problem with it.  

View 1 Replies View Related

Linksys Wired Router :: RV082 QuickVPN In Combination With Windows 7?

Jan 17, 2010

Recently I sold a rv082 router to a client.He uses a Windows XP environment to dail in using QuickVPN.A week ago an office admin wanted to connect using Windows 7 and it does not work.The client starts do dial and connects but the connection does not work.The admin does not use a router and there is no active software firewall.

View 3 Replies View Related

Linksys Wired Router :: RV082 VPN Pass-through Not Behaving As RV042?

Aug 15, 2012

We have almost identical networks in two offices, with the only difference being, one uses an RV042 and the other an RV082.The setup is: two WAG54GS ADSL modems carry PPOA ADSL connections with static IPs to the two WAN ports of the RV0XX.The WAG54GS routers are configured to DMZ all incoming traffic to the relevant WAN IP of the RV0XXs. VPN pass-through is also set on them. The RV0XX port forwarding is set to forward a selection of traffic such as, PPTP, HTTP, HTTPS, RDP, POP3, SMTP and Remote Desk to the external adapter of an SBS 2003 server which processes all operations including ISA and Exchange.Mail for Exchange arrive through both ADSL connections for redundancy. VPN connection requests from remote users to the SBS come in through both ADSL connections.The office fitted with RV042 works fine and does all the following without problems.The office fitted with RV082 has issues. Remote VPN requests comming from ADSL to WAN port 1 of the RV082 connect successfully to the SBS2003 server, but the VPN requests coming from ADSL to WAN port 2 fail to connect! Similarly, incoming mail destined for Exchange don't get through if coming from ADSL of WAN port 2.I have updated the firmware on both RV042 and RV082, but the RV082 still has the above issues.

View 1 Replies View Related

Linksys Wired Router :: RV042 / RV082 Timeout Bug Found

Jan 23, 2008

telnet/ssh sessions time out after 30 minutes of in-activity This only happens in the case of a server that is setup behind the firewall, and of course port forwarding is used. If one unchecks the radio button for the enable firewall the sessions do not timeout at all. This is very reproducable in all recent (1.3.9) versions of RV042 and RV082 routers.

View 2 Replies View Related

Linksys Wired Router :: VPN Tunnel Disconnect Between RV016 And RV082

Jun 2, 2011

Currently I have a VPN tunnel setup between our company locations. Location A has Linksys RV016 and Location B has RV082.  Everything has been working with no problems for the past 2 years with only minor disconnect issues in the VPN tunnel between the locations.
 
For the past 2 weeks I have been running into issues with the Tunnel. Users in Location B are reporting problems with losing connection to applications that are hosted in Location A. At first I start with doing a ping to router address in Location B and I get "request timed out". Next I login to router in Location A and under VPN I notice that the VPN tunnel is not disconnect (I see disconnect button). Once I click on Disconnect the screen refreshes and that seemed to restablish connecting with router in Location B. The drop connection has been been going on for the past 2 weeks and only happens once a day specifically between 1 PM and 3 PM EST. I have been reading all over the internet and no luck at all. The VPN tunnel settings are the same on both routers and under Advanced options both Keep Alive and Dead Peer Detection (DPD)  are checked.

View 1 Replies View Related

Linksys Wired Router :: RV082 Slowing Down Internet Connection

Jul 14, 2011

I have a RV082 Linksys router and at the moment it is slowing down my internet connection by a significant amount. With the router, I get about 3 Mbps and with a modem directly connected to my computer I get about 24 Mbps. Before with the router I used to get 15 Mbps, which is understandable because it is connected to 4 computers total. Maybe my setup has something to do with it. I got a cable that is connected to a modem, the modem is connected to the router, from which one port is connected to a computer, and another is used to connect to a Netgear switch, which in turn is connected to 3 more computers.
 
Everything was fine until I went on a trip and wasn't home for about 2 weeks, and when I came back, this happened. I tried restarting the modem, the router and all to no avail. I also tried to do a factory reset on the router and again got slow speeds.

View 1 Replies View Related

Linksys Wired Router :: RV082 Load Balancer Between 2 Providers

Feb 25, 2011

I have got Linksys RV082 in my home network to use it as load balancer between 2 providers.Is it possible to make some customisation in scenarioses and logging system? As I understand the device is based on some Linux core and Linux infracrtucture. So it must me available in sources... How I may get this kind of access? I want to get ssh/telnet or other raw access to installed on the device OS and manual control it, treat around web-UI. How may I do it?

View 1 Replies View Related

Linksys Wireless Router :: Internet Cable Goes To Wired RV082

Apr 19, 2012

I have a Linksys RV082 Wired router. It works great but doesn't do wireless.  I have a Cisco/Linksys E2500 Wireless router for my wireless devices to use.  the RV082 is on the 192.168.1.x network. The E2500 is on the network 192.168.0.x network.  The Internet cable goes to the Wired RV082, and a line comes out of there to the wireless router.  This all works fine except for a couple inconveniences.I have an iPad that connects wirelessly and some of the apps offer an http:// option so I can transfer files to that app.  I also have a network printer hooked in wired, but wireless devices can't see it.I have 2 problems:

1) In order to transfer files from my laptop (which I have hooked in to the wired network most of the time), I have too disconnect the wire, connect wirelessly, then I can transfer the files.  Works, but it's inconvenient.

2) I would like a netbook that I have on the wireless connection to be able to print to my wired network printer.
 
It appears that the 2 networks are not seeing each other.  Here are the things that I have tried:

1) I disabled the DHCP on the wireless router.  My thought is that requests for an IP address sent to the wireless router would be forwarded along to my wired router... NOT.  On my iPad and Wii, they could no longer connect wirelessly. Strangely enough, with the wire disconnected and connecting wirelessly with my laptop, I was still getting a 192.168.0.x IP address, even though DHCP was disabled on the wireless router.
 
2) Thinking that I would just manually put the wireless router on the 192.168.1.x network, instead of telling it to get an IP dynamicaly from the Internet connection, I manually set it's IP to 192.168.1.245.  Bad mistake.  I could not connect to it at all from anywhere then.  The only way I could fix that was to hook it wired to my notebook, assign a static IP to my notebook on the same network as the router, then I could got to the setup page and set things back the way it was.
 
Another thing... Even when I'm only connected wired on my notebook and wireless is disabled, I can ping 192.168.0.1 (the wireless gateway) and it returns a value. But, when I try to go there in a browser, I get a "page not found" error.

View 2 Replies View Related

Linksys Wired Router :: Setup VPN Tunnel Between RV082 And WRV200

Feb 23, 2011

I'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.

View 1 Replies View Related

Cisco :: 2960 / 3750S / 3750X / 6504S - SNMP Trap Configuration

Sep 10, 2012

I have Cisco 2960's, 3750's and 3750x's all running IOS on the access layer.  I have Cisco 6504's running IOS on the Distribution and Core layers.  I am looking to monitor redundant links through Spectrum by having specific ports send traps but I have run into trouble finding how to configure it.  I would like to have:

1. Logging enabled for all links (Fiber and Copper) so that I see all links up/down messages in the syslog
2. SNMP traps sent for linkup/link down messages only for redundant links (ex. Dual Up links from Access Layer or Redundant Ether channel Links on Dist Layer)
3. SNMP traps should be ignored/not sent for all copper ports.

View 3 Replies View Related

Cisco Switching/Routing :: 3750 SNMP Trap Send Every 30 Seconds

Dec 17, 2012

I have a snmp trap sent every 30 seconds from one of my cisco switches (a stack of 3750 to be precise): ccStatusMemberStatusChange. Do you know what it is and why it is sent continuously?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved