Linksys Wireless Adapters :: WUSB100 Doesn't Connect In N-only Mode To WRT150N Router
Nov 12, 2011
with my Linksys WRT150N router in "N-only" mode, the usb adapter WUSB100 doesn't connect. In the datasheet is written that it is B-G, but also N compatible..[URL] It connects only when the router is on "mixed mode" (B-G-N).
The device works great, the only thing is that it doesn't connect to N networks.... cause i think it is not N compatible. When i look for networks, Windows shows me that there is my N network, but when i click connect, after a few seconds, appears "impossible to connect".... but if i set the router on "mixed mode", no problems.
View 9 Replies
ADVERTISEMENT
Jun 13, 2011
I have had a wusb100 on my computer for some time. Yesterday it kept showing that it had a very weak signal and wouldn't connect to the internet, although the other computers in the house were fine.. I've reinstalled it and the device manager shows it working fine. The tv screen icon advised me that there are wireless networks in the area but the adapter isn't connected. When I click on the pop up, it tells me that there are no wireless networks in range.
View 4 Replies
View Related
Sep 5, 2012
I have a Linksys WUSB100 ver.2 which i'm using on my desktop (uptodate Windows 7) for over a year now. I never had any problems with it until about a week ago.
After starting the computer, it had no network-connection, nor could it find any network anymore . The led-light keeps flashing blue and the device gets pretty hot.
I've tried about everything, i think:
- I've tried to update the drivers, but the installed driver were already uptodate.
- I have re-installed the device with no effect.
- i've installed the device on 2 other computers; my Windows 7- laptop and my old Windows XP SP3-computer. The problems were the same there.
View 2 Replies
View Related
Oct 10, 2011
My WUSB100 which used to run perfectly suddenly started disconnecting. When I unpugged it, I realized that it was extremely hot. When I leave it to cool down and plug it again it works perfectly... for about two minutes. After two minutes it disconnects, no site loads, all downloads stop... etc. but the indicators on my computer do not even realize that there is a problem with the device... when I unplug it, I see the same result: too hot...
View 3 Replies
View Related
May 4, 2011
I have just bought the aforementioned Wi-Fi adapter. I have installed driver for it, and in Device manager in General tab I can see that "This device is working properly". owever, the corresponding connection in Network Connections is disabled, and I can't enable it. When try to "Set up a new network" - I only see a blank window with no devices listed. Windows network Diagnostics says: There might be a problem with the driver for the Wireless Network Connection adapterDetected
View 1 Replies
View Related
Jan 9, 2012
I am having trouble installing the wusb100 adapter on a Windows 7 Pro 64 bit machine. I have downloaded the updated files and when I go to install the software, I get to the section that says, "plug in the adapter." At that point, it says it can see the adapter and it sits for 3 minutes trying to complete the install. The I get error 211 which says the adapter is plugged in wrong and to try again. I notice that the adapter is set up with drivers in the Hardward Management area of Windows, however, I cannot access the adapter to set it up. Thoughts? I have also tried to manually install the drivers but they are installed. The trouble is I can't see the adapter.
View 2 Replies
View Related
Nov 30, 2011
I just installed windows 7 on my wifes new com and the device couldn't detect any connections using the default drivers (windows called it an nvidia wireless network card). I downloaded the drivers put them on her hd via flash drive and attempted to update the device drivers through the device manager but it says the drivers are already up to date. I uninstalled the device and windows called the device MCF-J415W and when I tried to update the drivers again it said the drivers were not correct. I'm not sure what is going on here and why linksys doesn't just have a .exe driver installer. I've had the same issue with my wife's computer when it had win xp except it didn't have any generic drivers to install. Also I tried selecting the driver from the list of pre-loaded drivers and found one for the exact device but it would not install those either.
View 2 Replies
View Related
Mar 15, 2011
So my AE1000 adapter doesn't connect to my network after waking my computer up from standby mode. I tried disabling the power management option where it allows you to turn off the device to save power but it still won't automatically connect to my network. I have to manually remove the adapter from the usb port and plug it back it for it to work again. I'm using Windows 7 64 bit,the latest drivers from Cisco's website, and my anti virus program is Microsoft Security Essentials
View 4 Replies
View Related
Aug 8, 2012
I have a wrt150N that I am trying to determine whether it's dead or not. I cannot connect to it directly, even if I plug my laptop directly into the Router. Pressing the Reset button does nothing, the lights don't even flash?If I change my Ethernet cable it does represent which port I'm using but I can't ping 192.168.1.1 either? I want to try and flash the bios but A: there's no file to download for this model and B: I presume I need to be able to connect in order to do the flash?
View 4 Replies
View Related
Feb 28, 2011
I have the WUSB600N wireless adapter, and I'm using it with Windows 7 Ultimate 64bit. I'm using the latest driver available, 3.0.10.0. When Windows first starts, the adapter is not working properly and fails to connect to any networks, no matter how long I wait. If I unplug it and plug it back in after Windows is already running, I do not have this issue. This also does not occur when "restarting" the machine; only when turning the machine off and then back on.
View 2 Replies
View Related
Aug 29, 2011
Called earlier the guy is really impatient and just wanted my credit card detail to install some remote software for technicians to fix from their end. Ethernet connection is fine1. wireless with iphone and ipad is conected with correct password and strong signal. But 99% of the time there is not connection while signal is still strong.2. wireless connection with another laptop using Cisco Network USB adapter WUSB100. After wireless work detected and enter the same security key as ipad used. Could not work.
View 2 Replies
View Related
Jan 10, 2012
I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
View 4 Replies
View Related
Aug 9, 2011
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies
View Related
Aug 17, 2011
I am trying to extend the network within our church. The main router currently being used is a NetGear WNR1000. I have two spare lynksys routers (WRT150N and aWRT54G). Can I connect them wireless to extend the network throughout the Church? If so, do I have to hard wire the first two routers or can this be done through the wuireless connection?
View 1 Replies
View Related
Feb 17, 2012
I've just installed the software for this adapter on Windows XP and it does not see the network (on a Belkin G Plus MIMO router). It doesn't see any networks at all. I've tried the manual setup but it gives me a "Cannot associate with the Access Point" message.
The adapter is plugged in and the green power light is lit up.
View 4 Replies
View Related
Feb 15, 2011
I have a Wireless-G USB Compact USB Network Adapter (WUSB54GC V1.0). Running XP. How do I set Promiscuous mode for this adapter?
View 1 Replies
View Related
Feb 13, 2011
I've just bought this wireless usb today and attempted 2-3 times to be able to connect with my router (D-Link's DIR-601) but it for some reason failed to do so, until the little usb didn't have its green light flashing anymore... and when i reconnected it to my Windows XP it rang its error sound... and I kept having this message from the Wireless Wizard that it's not connected appropriately or something...and that i have to run the setup wizard again.
View 1 Replies
View Related
Aug 29, 2011
I cannot use my AE1000 device for more than twenty minutes connected on windows ultimate 64bit.AE1000 doesn't startup with Windows 7 64bit.The led light still turn on when I turned off my PC.
View 3 Replies
View Related
Jan 29, 2013
The latest driver is version 3.2.7 for Windows 7. I am still on the 3.0.2.0 driver which works fine for me. I just wanted to note that the 3.2.7 driver obtained from Windows Update doesn't work well, drops connections and takes longer to establish a connection. I've tried to update twice and each time I go back to the older driver.Can someone at Linksys examine the performance of this driver?
View 9 Replies
View Related
Mar 26, 2010
I have installed manually drivers for wusb54gc v3, but the wireless manager still write error 211. I do see the adapter in device manager and it's writen than it's working, bat still the manager doesn't work and ican't see any net. OS Win7 32bit.
View 9 Replies
View Related
Nov 26, 2007
I'm trying to setup Xbox live for my Xbox 360. I have the WRT150N wireless router and just got the wireless adapter that plugs into the 360. It said the adapter couldnt pick up the signal then i realized i needed to enter the WPA key from my wireless router. I checked the information on the router and it only gives me the serial number and MAC address. How I can find out what the WPA key is for the router??
View 5 Replies
View Related
May 13, 2011
I am currently at a friends house attempting to fix a situation he is having with his' wireless router, it is a Linksys WRT150n.Connection to the internet is possible via ethernet connectivity, however wireless is another story, devices can see the network but cannot connect to it, i have disabled the security key from the network to see if it was a simple password incorrection but still no dice.The current basic wireless settings have network mode set to mixed, and radio band, wide and standard channels set to auto, all other settings in the advanced tab are set to their default values.
View 1 Replies
View Related
Jan 23, 2008
I have the wireless-n wrt150n router. I have it wired to my computer and have it wirelessly connected to my ps3. But for some reason there is another unnamed device listed under My Network. My network was not secure before, but I changed it to secure when I noticed the unnamed device. How do I remove that unnamed device from my network?
View 3 Replies
View Related
Nov 24, 2007
Laptop keeps disconnecting from WRT150N
View 9 Replies
View Related
Sep 1, 2012
I want to replace a WRT150N with an E2500 and retain the setup/settings of the WRT150N.
View 2 Replies
View Related
Sep 7, 2012
Up until about midnight tonight, my router, which has been plugged in to my cable modem, has been working fine for years, both wired and wirelessly. Suddenly, however, I went to log on to my desktop PC (wired connection; Windows 7), and I had no network connection. ipconfig indicated "media disconnected." My cable-based phone service (VOIP) is still working fine at this time.
First attempt - unplug router, wait 15 seconds, plug it back in. Still no good, though my network sharing center indicated that the network connection was appearing/disappearing every few seconds, never actually getting "internet" connectivity.
Second attempt - attempted to use a WIFI-based device (iPad), which could not see my home network by name at all.
Third attempt - reset both the cable modem and the router, bringing the cable modem up FIRST. Same results as the first attempt.
Fourth attempt - plug the wired PC directly into the cable modem - this worked fine and is how I am submitting this post as I type. So the cable modem is working properly.
Fifth attempt - look up the information on how to reset the router to factory defaults. Used a paperclip to depress the reset button for 10- and on a subsequent attempt, 30-seconds (no obvious "reset" blink pattern was observed). Plug PC back in to router. PC would not obtain any DHCP-based IP address and the network sharing center was still behaving as in the first attempt.
Sixth attempt - disconnect the cable modem uplink and see if I could get the local network functioning. Now I noticed that the LED patterns on the router were behaving as:
- Power and my PC's slot number lit
- All lights lit
- All lights off
- Power and my PC's slot number lit
- etc
View 2 Replies
View Related
Aug 6, 2011
In my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.
View 4 Replies
View Related
Apr 10, 2012
I have two WiFi Routers (TP-Link WR340G and Linksys WRT150N). I am wondering how can I connect this two routers via wireless fidelity
View 1 Replies
View Related
Aug 9, 2008
I've just bought a WUSB300N Wireless USB Network Adapter and installed it with the Vista drivers on my Windows 2008 server. Drivers are succesfully installed and the Device status says "Device is working properly" but when I want to connect to a network it doesnot show any networks. I'm sure there are network available because I'm connected now on my other laptop ;-) typing this message.
View 5 Replies
View Related
Feb 25, 2013
I use a WUMC710 bridge with desktop PC and a Printer connected to it. When those two devices have been inactive for a while the bridge goes into sleep mode and loses the connection Back to my EA6500. Trying to print something from wireless devices connected to the 6500 elsewhere in the network doesn't "wake up" the bridge. Ihave to unplug the power supply and restart it.
View 2 Replies
View Related
Jan 6, 2012
Changing the NAT Type to open because I can't play with some of my friends on Playstation.
View 1 Replies
View Related
Dec 31, 2011
chaning the NAT Type to open because I can't play with some of my friends on Playstation.
View 2 Replies
View Related
Nov 9, 2012
I can get regarding using the Collobos Fingerprint software through my WRT150N router. I'm using Windows XP SP3 and immediatly after installing (which went extreamy well) it immediatly found and listed all of my home network printers. All of the wired and wireless windows based systems in my house can see and print to the printers without any problem. However, getting ANY of my apple devices (iPad, iPhone etc ) to print will not even show them as listed on the device when I select print on the devices. Collobos says that I have to make sure that Ports UDP 5353 doe Bonjour and TCP 6361 for FingerPrint need to be open both ways for it to work, I have no problem getting into the router settings and have set them up as stated above in Port Range Triggering and enabled. Also made sure Filter Multicast was not check marked in Security. Unfortunatly, that doesn't seem to work as I had hoped.
View 3 Replies
View Related