Linksys Wireless Router :: E3200 Router Can't Connect To Internet

Mar 20, 2013

I bought a Cisco-Linksys E3200 8 months ago and it worked well until last month. I usually power down the router after midnight & power up in the morning and evevry time it can connect to internet through DSL modem without problem until this Feb. Most of the time after powering up the router it just can't connect to internet anymore. I am sure the AT&T DSL modem is working. I have to reboot/reset the router & DSL modem several time to get router to connect to internet again. The order of resetting/rebooting DSL modem & E3200 router seems to make no difference. It just appears suddenly the router can connect to internet by chance. I changed router IP and it didn't work either. It's really annoying becuase I have to spend 10~40 minutes to resetting/rebooting DSL modem & router to get internet connection every day. 

View 9 Replies


ADVERTISEMENT

Linksys Wireless Router :: E3200 Cannot Connect To Internet?

Dec 18, 2011

The problem I have was that last night I unplugged my router and replugged it back in. As soon as that happened, there was no connection between my router and the modem. This morning, I tested to see if it was the modem by connecting an ethernet cable from my desktop to it, and was able to get online. Then, II reset the router and a sucessful connection was made between the two. On my desktop my old network was gone, but the Cisco network was there, leading me to create a new network as if it was a new router. After setting up a new network, I am not able to connect to the internet.

View 1 Replies View Related

Linksys Wireless Router :: E3200 - Cannot Connect To Internet

May 14, 2011

I have purchased a new E3200 to replace my old Linksys router.  It locates my computers and sets up a network, but cannot connect to the internet via my Comcast cable modem.  I have read on this forum about Mac address issues, but it has located the Mac address.  The internet IP address is all zeros, and releasing and renewing the IP does nothing

View 9 Replies View Related

Linksys Wireless Router :: E3200 Will Not Connect To The Internet

Jun 17, 2012

I have a Telus Wireless modem and got a linksys router to try and expand the range & strength of the wifi. However,whenever I plug in the router and try to set it up, I can get connected to the router but no internet connection.I have tried everything I can - restarted the modem and the router several times, connected and reconnected, rebooted the whole of the router system, connected with an ethernet cable straight to the router from my laptop. In the settings, I have tried to mess around with the settings and more, and whenever I screw up I reset the router to defaults again. 

View 3 Replies View Related

Linksys Wireless Router :: E3200 Cannot Connect To Internet

Jan 3, 2012

I have was that last night I unplugged my router and replugged it back in. As soon as that happened, there was no connection between my router and the modem. This morning, I tested to see if it was the modem by connecting an ethernet cable from my desktop to it, and was able to get online. Then, II reset the router and a sucessful connection was made between the two. On my desktop my old network was gone, but the Cisco network was there, leading me to create a new network as if it was a new router. After setting up a new network, I am not able to connect to the internet

View 3 Replies View Related

Linksys Wireless Router :: E3200 And Motorola DSL 2210-02 Will Not Connect To Internet?

Oct 29, 2011

I justed purchased a Linksys E3200 router to replace my old router that gave up the ghost.  I have it paired with a Motorola 2210-02 DSL modem.  The software that came with the router has created two networks but is unable to connect to the internet.  I have tried on both my PC and MacBook Pro and niether work.  I have the modem connected directly to my Mac and can get to the internet, so I know the modem is working correctly.  

View 6 Replies View Related

Linksys Wireless Router :: E3200 Lost Internet Connect Every A Couple Hours

Dec 4, 2012

I have a Linsys E3200 router for almost a year. It's been working fine until recently. It kept losing internet connection every a couple hours or even shorter. I have to power cycle the router in order to make it to work. However, sometimes that won't work either. I also tried to restore the router to the factory default but that doesn't seem to work.
 
I have updated the router with the latest firmware (1.04). I am using a cable connection and it never gives me any problem if I just connect my computer to it. I also test my network with another old netgear router that works just fine.  

View 9 Replies View Related

Linksys Wireless Router :: E3200 - Connect USB Hub?

Oct 18, 2011

I just ordered the E3200. It's suppose to ship today. I know it comes with 1 USB port for hard drives. Is it possible to connect a USB hub to the router so that I can connect more than 1 hard drive?

View 1 Replies View Related

Linksys Wireless Router :: E3200 Can't Connect Wired?

Aug 31, 2012

I have an E3200 router. I had been experiencing connection problems with my desktop that was wired to the router, and in an attempt to resolve the issue reset the router to its factory defaults. Now, as before the reset, I can connect to my router just fine via Wi-Fi (I have several devices connected this way) but none of the computers that I attempt to connect via ethernet are able to establish a connection. I have tested multiple cables with multiple computers using multiple ports on the router, to no avail. When I view the Status --> Ports page on the router, I can see the ports in use that I am connected to, but that is the only sign of connection that I get.

View 1 Replies View Related

Linksys Wireless Router :: Will All Usb Printers Be Able To Connect To E3200

Jun 10, 2011

Will all usb printers be able to connect to the e3200 by usb with the firmware update? If not, what printers will be supported?

View 9 Replies View Related

Linksys Wireless Router :: E3200 Can Connect Other Computers But Not IOS Devices

Dec 2, 2012

Just installed the E3200. Can connect other computers but not IOS devices to the router, except through the "guest" port.

View 2 Replies View Related

Linksys Wireless Router :: Cannot Connect To Admin Page At All On E3200

Feb 23, 2012

I don't have to completely reset my router as I have a ton of configs on it.  Anyway, recently for some reason, I lost all access to my admin page.  Cisco Connect also cannot find the router.  Funny thing is that all of my wireless profiles work just fine.  Meaning all of the computers in my home connect to the internet just fine using the router.  Both the guest access and WPA connected machines.[url]...

View 1 Replies View Related

Linksys Wireless Router :: E3200 / Can't Connect To 5Ghz Band

Apr 15, 2012

I'm using a Linksys E3200 router with a Motorola modem and an elite xbox 360 with a wireless N networking adapter. (Black with two antennas.) I just recently bought this router because I wanted some faster gaming. I wanted to put my xbox on the 5ghz so it would have it all to itself, and have the two laptops share the 2.4ghz. But it won't let me onto the 5ghz band... I can see it on my xbox but it won't connect to it at all. I can get onto the 2.4 band but its at 802.11G, so its not even giving me N there, when it should be. I'm not sure if this is an issue with my adapter or router...I tried finding stuff about it, and it looked like people were blaming it on linksys, but that was almost a year ago. And there was never an update on what happened.I can see the 5Ghz band on my xbox (but only if the channel width is on 20Mhz only), but I can't find it on my computer. Which I find weird. I've been trying a lot of things and I just can't get my laptop to find it. So nothing is using the 5 band, and all my devices are crowded onto the 2.4...Is there some step in setting up the 5Ghz band that I'm missing maybe?

View 4 Replies View Related

Linksys Wireless Router :: E3200 / Possible To Use As USB Hub And Connect Multiple Devices?

Jul 21, 2012

I just bought the E3200 and have it all set up and have been able to successfully print from the USB port. I want to know if you can use a USB hub to connect multiple devices to the router. I found a couple of similar questions on the forum, but they're all back in 2011 before the 1.4 update to Cisco Connect. 

View 1 Replies View Related

Linksys Wireless Router :: E3200 Couldn't Connect Via Wi-Fi Devices

Feb 9, 2012

I bought the E3200 to replace an older Linksys model. The older model worked but the signal was weak throughout the house. I installed the e3200 using the Cisco connect software but it told me that it wasn't sure I was connected to the internet. I wasn't. Showed a strong signal but could not connect via wireless devices or from the cable from  the router to the desktop.
 
I have LUS Fiber service which does not use a modem. I have had them recycle the signal several times and have done tried many different variations of the MAC numbers from ipconfig or from cloning. Have also tried it with the MAC cloning disabled so the router's MAC number is used. I have reset, rebooted and done just about every possible option.
 
 Spoke with my provider many times and they insist they are sending me a signal. They also recognized the router's MAC number on their end.I purchased one router and it wouldn't connect, so I exchanged it. All these shenanigans I have gone through are with the second router because I figured the hardware isn't the problem.

View 1 Replies View Related

Linksys Wireless Router :: Connect Error 80004005 With E3200

Jun 17, 2011

I had Cisco Connect and USB printing off of the E3200 working, but now I'm getting an error and cannot print to HP Laserjet P1006 on my E3200's USB port. Cisco Connect has an error: Error code: 80004005 Model name: Linksys E3200 Model number: E3200 Serial number: Firmware version: 1.0.01 build 3 Operating system: Windows 7 Software version: 1.4.11145.0 Connection type (WAN): DHCP IP address (LAN): 192.168.0.253 IP address (WAN): 192.168.2.100 Computer IP address: 192.168.0.149

View 9 Replies View Related

Linksys Wireless Router :: E3200 Can't Connect To Wifi Radios Wirelessly?

Sep 23, 2012

I just installed an E3200 to replace my old Linksys.  All my Nooks, IPADs, laptops and desktops are connecting wirelessly fine. However, I have 2 Wi Fi Radios that will pick up the network but will not connect and go into a network connect time out. One of the radios also has a hardwired connection and that is working fine.  I have checked and double checked the network name, WPA key, etc. Of course I have reset all the radios and reenter new data many times, both manually and auto.

View 3 Replies View Related

Linksys Wireless Router :: E3200 Cisco Connect Software Download?

Sep 3, 2012

I'm amazed that the entire e3200 support page is down.  Anyways until somebody from Cisco figures that out, I need analternate download link to the Cisco Connect software specifically for the E3200.

View 2 Replies View Related

Linksys Wireless Router :: E3200 Can't Connect To Live To Test Connection

Oct 21, 2011

I upgraded 3 days ago from a (WRT160N ver. 1) to a (E3200) After setting it up and syncing all the devices including the XBOX 360. After signing into Live I noticed that every time I power off and power on the console it's IP address would change causing the NAT to become moderate so I went over to the Xbox360 open the Network settings and Manually set the IP address Mac address, Gateway address. Then I opened the routers settings page and Port Forwarded the correct ranges also copied the IP address I manually entered earlier on the Xbox 360. On the router side I saved the changes restarted the console and my NAT was open, but here's the Issue now when I go to sign into Live I get a pop up saying I can't connect to Live to "Test the Connection". After I "Test the Connection" then and only then I can sign into Live.

View 9 Replies View Related

Linksys Wireless Router :: E3200 Internet Speed Fluctuations?

Mar 4, 2012

I currently use a Linksys E3200 and mainly direct connect it to my laptop. My current ISP is with Insightbb to which I use their 20.0 (20 Mbps) service. For the past 6 or 7 months I've had little to no issues with my internet connection until about a week ago. While directly connected to the E3200 I used to get up to about 20/21 Mbps at a constant rate. Yet now I'm lucky to get up to 13/14 Mbps. Also, the speed will sometimes fluctuate; shooting to as low as 8 Mbps and shooting as high as15 Mbps. I can verify that my ISP is not the issue. I've directly connected my laptop to the modem with success and received a healthy speed of up to 23 Mbps with no fluctuations. The problem only occurs once I directly connect to the router. Attempting to connect wirelessly shows the same, if not worse, problems.
 
I've attempted numerous factory resets and used the 30:30:30 method to no avail. I've tried power cycling the modem, router and laptop. I've tried disconnecting the router for up to 10 minutes. I've upgraded the firmware to the most recent update. I've tried setting a static IP. I've tried imputing the MTU manually. I've tried setting a MAC address clone. I've tried turning on/off UPnP. I've tried release/renewing my IP address. I've tried flushing my DNS. All of which I power cycled the router after each and every attempt.

View 1 Replies View Related

Linksys Wireless Router :: Internet Access Via Wifi With E3200

Oct 5, 2011

Is it possible to connect the E3200 Router to the internet over the wifi (WLAN) interface?Actually I can only use the ethernet port called "Internet" to connect with my Fritz Box router (which is responsible for my internet connection to my DSL provider).But I don't want to use 10m or more ethernet cable across my flat so it would be nice to use just wifi.

View 5 Replies View Related

Linksys Wireless Router :: Fluctuating Internet Speeds With E3200?

Feb 26, 2012

My new e3200 setup just fine with Cisco Connect.  I have consistently good speeds with a direct ethernet connection, but the wireless speeds fluctuate widely.  When I power cycle the router, I'll have perfect speeds for a few minutes and then it'll slow to a crawl (approx 0.5Mbps).  Then for no apparent reason, it will speed back up to normal, and then back down to a crawl.  I'm using the latest firmware and have allowed Cisco Connect to manage the router so far.This is actually my 2nd router, as Tech Support told me when I experienced this with the first router that it was defective, but I'm seeing the same problem with the 2nd router, so I know something isn't quite right.  

View 2 Replies View Related

Linksys Wireless Router :: E3200 Kill Internet Speed

Feb 24, 2013

I got 1Ggbit Internet. When i plug in PC i got 700+300+ on speedtest, if i plug in E3200 i got 9040. **bleep**?I play with all settings  nothing works... In status he show 1 ggbit internet and 1 ggbit Ethernet but he gives less than 100 mbit....

View 9 Replies View Related

Linksys Wireless Router :: E3200 - Internet Speed Drops?

Jul 17, 2012

We recently purchased a Linksys E3200 router, because our old router didn't take advantage of our internet speed. The router works fine, though the internet speeds again isn't as much as expected.
 
With a wired connection, we only get 80 Mbit/s of our full 120 Mbit/s, according to Speedtest.net. The Cisco Connect built-in speed test is even worse; only 40 Mbit/s. When we directly plug the computer into the modem, we get the full 120 Mbit/s, which indicates that the modem does have the connection speed. The router just doesn't give it to the computers attached.
 
I don't know about my wireless speed, as my wireless card in the laptop clearly is the bottleneck (it can only connect at 65 Mbit/s). Atheros AR9285 ftw.
 
We tried different cables, the one included with the router gives the same speed.

View 9 Replies View Related

Linksys Wireless Router :: E3200 Loses Connection To Internet Through Comcast

Jan 24, 2012

I have a problem with my E3200 that has happened at least 4 times since I first purchased, installed and configured it.  Initially I thought it might be something with Comcast, but a) I never had the problem with my Linksys WRT54G router and b) It seems I can now duplicate the issue by saving a config file and restoring it.The specific issue appears to be somewhat random.  At some point the connection to the Internet simply stops for no apparent reason.  I am able to ping the router and connect to it.  I am also able to drop and renew connections to the cable modem successfully.  Furthermore, I can ping my network side of the router, as well as the external address handed to my router by the cable modem, and the cable modem gateway address, but still no connection to the Internet.The only solution to my problem has been to restore the factory defaults to the router and reconfigure it from scratch, which does seem to fix the issue for a time until it occurs again.  FYI, I do not use the Cisco connect software because I have several custom port and QOS configs that are necessary for an IP Phone and other hardware on my network.

View 1 Replies View Related

Linksys Wireless Router :: E3200 Loses All Internet Access Until Reboot

Jul 27, 2012

My E3200 (firmware 1.0.04) loses access to internet every week or so and OK again when reboot.

View 6 Replies View Related

Linksys Wireless Router :: E3200 Internet Connection Randomly Dropping

Jun 23, 2012

i am a total n00b when it comes to wireless routers etc,.. i bought this router [E3200] about six mths ago, it has been working just fine untill a couple days ago, wher i woud be on the internet and all of a sudden, the internet connection drops, i am using a cable modem [ARRIS TM722G] ,i did a reset on the e3200 and put restore the settings that did last over night

View 9 Replies View Related

Linksys Wireless Router :: E3200 QoS And WMM Settings Slow Internet Down When Enabled

Feb 13, 2012

Ok, so I recently upgraded to a Linksys E3200. I am trying to get the QoS to work properly. I know that it is supposed to prioritize network traffic, so that if I have busy traffic but I am playing an online game, it should keep my gaming from stuttering while slowing other traffic down.
 
The problem is that every time I enable QoS everything slows down dramatically. I had a 200MB download that was going to take 5hrs with QoS enabled, that took 10min with QoS disabled. And with QoS enabled I can't even watch a youtube video without it pausing to buffer every 10 seconds. And that was the only PC/device using the network at the time. Again turning off the QoS WMM option solved  the problem. I have noticed this problem with multiple routers and brands and usually just disable QoS as soon as I set up a router, however I heard that I won't get the full benefit of 300Mbps without QoS enabled.
 
I don't have any special Voice over IP needs, or video streaming etc. and I rarely am using multiple network devices at the same time. Is there really any reason I should enable QoS? Also I never really play with the settings for QoS, I just figure that since it comes enabled by default it should work for the average consumer.

View 9 Replies View Related

Linksys Wireless Router :: E3200 - Westell 7500 Modem / PCs Not Getting Internet

Feb 7, 2012

I used these instructions to put my Fairpoint westell 7500 modem/router into bridge mode: [URL].  Then I hooked my new e3200 to the westell 7500, but no matter what I tried, I could not get any PCs hooked to the e3200 to be able to get to the internet.so able to get to internet too. My questions are:Is there any downside to doing it this way? (ie, not putting westell in bridge mode).Can this cause any slowness or conflicts? Any reasons why bridge mode may not have worked?

View 4 Replies View Related

Linksys Wireless Router :: E3200 Loses Connection To Internet Weekly / Daily

Jan 1, 2013

I recently replaced an old Linksys with a Cisco E3200.   All our devices get "stuck" periodically and can connect to the E3200 but not the internet.  We power cycle the E3200 and all is fine.  But only for a period of time, then we need to power cycle again.  The range is less than my 4 year old Linksys was also, devices maybe 30 feet lose their connection even more quickly, forcing more frequent power cycling. 

View 2 Replies View Related

Linksys Wireless Router :: E3200 - QoS Enabled / Routing Stops From LAN To Internet Side

Dec 10, 2011

E3200 works great until I enable QoS.  The device uses QoS and works find until reboot.  If QoS is enabled and the device is rebooted, its stops routing from LAN side to Internet side.  Administration-->Diagnostics allow me to ping/trace route to Internet sites and local LAN clients but cannot reach Internet from local LAN.
 
Windows networking icon indicates "No Internet access".  I can ping other devices on local LAN. 
 
Disabling QoS restores routing and you can re-enable QoS after that and all is well.  Unfortunately, if there is a power failure when I', not there to disable/re-enable QoS afterward, other household members can't use the Internet till I get home.
 
Wondering if any other QoS users have observed the same problem.

View 7 Replies View Related

Linksys E3200 Won't Connect To The Internet

Jul 27, 2012

I've bought this router about seven months ago. I tried setting it up right when i got it but it didn't work. I ran out of time during my break and am now getting around to trying again. I've tried numerous resets and reboots, messed with most of the settings individually, but I never can connect to the internet through the router. The internet works with my old linksys router and directly connected to the computer, just not when connected to the router. I've tried calling up my internet provider, and the tech guy couldn't figure out what was wrong either. We have a DSL connection, and the MAC address of this computer is cloned into the router if that makes a difference.

View 2 Replies View Related

Linksys Wireless Router :: Set Up E3200 As WAP?

Aug 3, 2012

Trying to convert a spare router (Linksys E3200) into a wireless access point toextend my wireless coverage. I thought knew how to do this but having a problem.Steps I followed are:1. Disable the E3200 DHCP server2. Change E3200ip address from 192.168.1.1 to something else3. Disable the firewall4.Make wireless settings5. Connect it lan port to lan port with primaryrouter.The problem I am having is that after I finish step 2 the routerreboots with the browser trying to access it at the new ip address. But thebrowser will not connect.I am doing this on a laptop that is disconnected from my network while I am working on the E3200. It is connected byan ethernet cable to an E3200 lan port. I also tried it wireless with the same result. Browser will not connect at any ip address except 192.168.1.1 and then only after I factory reset the beast to regain the 192.168.1.1 ip address

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved