Linksys Wireless Router :: WRT54G No Access After Loading Configuration

May 22, 2012

I have a WRT54G with updated firmware.  Today I saved my configuration to a config.bin file.  When I tried loading the file, the admin screen went blank.  Now I am no longer able to access either the internet or the router's admin page.   Is a hard reset my only option?

View 6 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT54G V6 Setup Screen Not Loading Properly

Apr 27, 2007

When I go to the router setup screen via 192.168.1.1 the screen does not load properly in MSIE or Firefox. Text does not load.The graphics load okay, and the dropdown boxes, checkboxes, etc. Since many of the links are from text, and all of the descriptions, it is impossible to navigate properly. I managed only by using Firefox's Page Info, Links tab and cutting & pasting. A couple of screen captures are available [URL] have downloaded the latest firmware, but while I can get to the Administration page, much less click on, the Upgrade Firmware sub-tab.

View 3 Replies View Related

Linksys Wireless Router :: WET200 Configuration To WRT54G?

Nov 24, 2011

I've got a WET200 connecting to a wireless router (linksys WRT54G) setup thru the WET200 site survey.Does the WET200 need to have an ip with the same sub net as the network the WRT54G is connected to?I have a laptop hooked up the the WET200 with a static IP.  I cannot ping IP's of the same sub net on the network the WRT54G is connected to nor see anything on the internet?
 
WET200 connected to wireless AP WRT54G (192.168.23.3)
WET200 IP address = 192.168.23.8
Laptop IP address = 192.168.23.218 (connected to port 1 of WET200)
 
I can configure the WET200 via the laptop, but not able to see anything across the bridge?

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Configuration / It Keeps Losing Connection

Aug 21, 2012

I have a WRT54G router anf DSL modem. My router keeps losing connection, wired and wireless (My connection is not visible on any laptop). I tried briged mode on the modem and I tried the configuration CD. Everything works for some months or weeks. Sometimes the CD setup asks me for manual configuration. I am using modem to desktop connection?

View 2 Replies View Related

Linksys Wireless Router :: WRT54G V8.2 Cannot Access Setup

Apr 13, 2012

I had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:

Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.

View 5 Replies View Related

Linksys Wireless Router :: WRT54G Can't Access Own Sites

Nov 14, 2011

My own sites were down & I can't view them on my computer now.This is the 2nd time this has happened to me with router WRT54G.Every time there's a problem with my hosting company & my sites go down, my router blocks them once the sites are back up & running.When I plug directly into the modem I can access them, but then I can't use my phone, etc.I've recycled & I keep trying to find how you save your settings on your router so I can do a cold reboot, but I can't find the instructions anywhere.Why does it keep doing this & how to save the settings & restore them.

View 2 Replies View Related

Linksys Wireless Router :: Use Wrt54g As Access Point?

Dec 11, 2011

I am using a newer wireless router but would like to use my older wrt54g router as an access point (wired and wireless) at the other end of my house. how to do it, and what the specific settings should be, especially the security settings. I can connect the wrt54g via a homeplug (cannot run a LAN cable). I had previously tried an Aztech wireless homeplug but found the security feature to be worthless and everyone was able to "break-in".

View 3 Replies View Related

Linksys Wireless Router :: Can't Access WRT54G Through IP Within Browser

Apr 7, 2012

I can't access the router through the IP within the browser. It's an older WRT54G. I've never used the downloaded software that allows you to connect to it, but that's what I was going to try.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Possible To Get 2 Access Points

Apr 4, 2012

I have a E4200 as well as a WRT54G. I'm looking to create two different access points to the same network, one access point being 802.11g (WRT54G) and the other being 802.11n (E4200) I want to do this because I need the extra speed from 802.11n for streaming video to my consoles. The problem is that there are multiple devices that only reach up to 802.11g. Would it be possible to plug the WRT54G into the E4200 in order to give a second access point (probably with different SSID) so that 802.11g devices can connect to the network, without having to destroy my 802.11n network? The WRT54G is currently running DD-WRT.

View 3 Replies View Related

Linksys Wireless Router :: No Internet Access Using WRT54G

Dec 29, 2011

wrt54g wireless router so we could get Netflix through our Wii. I have a one year old Compaq and am running Windows 7 with a wireless Internet connection through my service provider. I installed the router with no problems and was able to get online with the Wii. However, I am no longer able to get Internet access on my desktop. It shows that my Internet is connected, but it shows "No Network Access".  I had gotten on fine at first, then I went to the 192.168.1.1 site to configure my data.  I changed my time zone and then went to secure my connection.  I cannot remember the exact option I chose, but I think it was something like WAP2 Personal. As soon as I selected that the screen froze and I can no longer access that site or get online through the router.

View 3 Replies View Related

Linksys Wireless Router :: Wrt54g V.2 Can't Access Via Web To Device

Jan 31, 2013

I upgraded my wrt54g v.2 with a firmware for wrt54gl and now, the power light is continuous blinking and I can't  access  via web to the device.I tried to reset it and replace the firmware without success.

View 3 Replies View Related

Linksys Wireless Router :: WRT54g / Can't Access 1 Website

Aug 3, 2011

I can't access a particular website with my Linksys WRT54g router in line, but can do so if I hook my mac directly to the ISP's modem.  I have checked the firmware of the router and it is up to date.  This is happening with only one website. It happens on multiple browsers. Using an imac with OSX 10.8.

View 4 Replies View Related

Linksys Wireless Router :: WRT54G V5 Cannot Access Internet

Jul 4, 2011

I just got a Linksys router from a moving neighbor.  The router is a Linksys WRT54G v5. She didn't have the power adaptor, so I found one that is 12VDC 500mA and it works.  The factory resetted the device.  I always get a signal, but it has that little error sign on it.  It says my internet connection is broken.  I believe this is caused by a bad ethernet port, but I have gotten into the internet sometimes. I have another router but it doesn't work either. On the other router I get a signal that as no error sign and says "Internet Access" but I still cannot access the internet.  My laptop's network card works.

View 2 Replies View Related

Linksys Wireless Router :: WRT54G - Access Restriction

Mar 19, 2012

target 192.168.0.21following are rules of access restriction on WRT54G1.rule A- 07:00am~10:00am,internet access allowed, keyword blocked such as Facebook,mail.2.rule B- 10:05am~10:00am,internet access allowed, no keyword blocked.but 192.168.0.21 fails to access internet after rule A expired.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Remote Access (VPN And RDP)

Nov 29, 2011

I'm using a Linksys WRT54G in my home and I have it set up to allow me to connect remotely (VPN and RDP) from work. I do this every day and it works perfectly. The problem I'm having, though, is that every morning it doesn't work until my wife wakes up her laptop. After that it works fine, whether her laptop is on or off. It behaves as if the router is "asleep," and when she generates some local network activity, it wakes up, thus allowing me remote access.
 
I believe it's a router issue and not a computer issue because not only does it affect VPN and RDP, but even the router's remote management interface is unavailable until this happens.
 
Some more details about my home setup. I have a fixed IP address assigned to me by my ISP . All computers connect to the router wireless VPN and RDP is routed to a desktop computer running XP SP3 that is always on (it never goes to sleep or hibernates)The router is enabled as a DHCP server (192.168.0.2 thru 11)The desktop computer is set up with a fixed IP address (192.168.0.100)The router is set up to forward VPN and RDP traffic to the desktop . Here's some screenshots that may be useful.
 
Basic Setup  Port Range Forward Management
 
Pretty much every other setting is defaulted. Like I said at the start, my setup works perfectly and I'm very happy with it. I just can't figure out why every morning it doesn't work until my wife uses her laptop?
 
When I'm at work, hers is the only computer on the local network getting assigned an IP by the router. Until she turns on her laptop, the DHCP client list is empty. Could it be that the router needs at least one connected device assigned an IP by its DHCP service in order for it to receive external connections?

View 6 Replies View Related

Cisco WAN :: Loading Configuration From Flash Card In 2811 Router?

Jun 6, 2011

have remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
 
boot config flash:<Config file>
 
where <Config file> is the file on the flash.
 
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
 
Is there a similar process for other classes of Flash cards, specifically Class C?
 
or
 
The router flash be set as a Class A to support this functionality,
 
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
 
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.

View 5 Replies View Related

Linksys Wrt54g With 4.2.1 Firmware - Restricting Wireless Access From Router?

May 27, 2011

Is there a way to restrict wireless access to my router from wireless pc's in my home. Two grandsons are off from school now, and are playing online games to the wee hours of the morning. Can I do something to have the routher shut off their connection at a certain time? Is that possible. If I have to go back to dd-wrt to do that, fine. I have lynksis wrt54g with their 4.2.1 firmware.

View 5 Replies View Related

Linksys Wireless Router :: Make WRT54G An Access Point Only?

Nov 25, 2007

I need to make my WRT54G an access point only. I tried information contained on Linksys site, but I can't seem to get it to work.

View 9 Replies View Related

Linksys Wireless Router :: Can't Get Access Restrictions To Work WRT54G V3

Nov 24, 2011

I am trying to get a cell phone to have access to my LAN from 3am to 7am.  I gave the policy a name, allowed access, checked everyday and the time 3a to 7a.  Under edit list of PCs, I entered the MAC address of the phone, and I have also entered the MAC address of the phone on the wireless>edit mac filter list, though didn't know if I should.

View 2 Replies View Related

Linksys Wireless Router :: Wrt54g Access Restrictions For Time?

Sep 2, 2011

I keep trying to set access restrictions for my wrt54g router for time. There is no 12 for time so I'm selecting 11:55 pm to 6am but I keep getting an error message of, "end time must be bigger then begin time." I get this no matter if I select 9pm, 10pm, etc.

View 3 Replies View Related

Linksys Wireless Router :: Cannot Access WRT54G Setup Page

Jan 19, 2013

I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G / Unable To Access Gateway

Jul 18, 2006

I'm unable to access my linksys wireless g broadband router (WRT54G)'s access gateway. (192.168.1.1)The gateway page doesn't load, at all. It doesn't ask for the user or password at all. On any of my internet browsers (firefox, and internet explorer)Anyway of fixing this would be appropriate.

View 2 Replies View Related

Linksys Wireless Router :: WRT54G Can't Access A Particular Range Of Internet

Aug 3, 2012

We have a WRT54G (hardware v6) which we have used for a couple years in conjunction with a cable modem to make a home wifi network. In the past few days, we've been unable to access any sites in the IP range 130.160.x.x (that is, those at The University of Alabama). A particular example is ua.edu (130.160.4.131). The rest of the internet works fine.This is on Ubuntu 12.04, Windows 7, or Android ICS; with Chrome, Firefox, IE9, or SSH. If I connect the modem to an Ubuntu laptop directly by USB, I can get to ua.edu just fine.
 
I tried resetting the router to factory defaults, upgrading the firmware, connecting via ethernet rather than wifi, and using the Google DNS servers 8.8.8.8 and 8.8.4.4 in the router, but the problem persists. Naturally, UA's helpdesk, Comcast, and Linksys were all either useless or uncooperative. [code]

View 9 Replies View Related

Linksys Wireless Router :: Internet Access From DSL Modem But Not From WRT54G

Dec 25, 2011

I am trying to get wireless internet set up again and have run into a big issue.  Previous wireless router was also a WRT54G and she had problems.  I gave her my old one that I was no longer using, but it was still working with no problems.
 
The problem that I am having is that we are unable to get internet through the wireless router.  We are able to get the desktop connected to the internet when we plug it directly into the DSL modem, but when we plug the wireless modem into the DSL modem and the desktop into the wireless modem, then we don't get any internet connection at all.
 
I had her do a factory reset on modem so that we were starting fresh.  I have also tried unplugging both modems and then pluggin in the DSL and then Wireless modem, with no change.  We have the ability to get into wireless settings page, but I'm not sure what in there to change that would make any difference on this one.
 
I know that this problem isn't actually a wireless problem, but it has to be related to the modem.  We haven't even been able to get to the wireless part of the set up and we are already running into problems.

View 7 Replies View Related

Linksys Wireless Router :: WRT54G Can't Access Work Group

Sep 9, 2010

With my WRT54G my network works fine.All my computers of Work group appears in Network (Windows XP and Windows Vista)With my new WRT610N, it is not the same :

- I can't access Work group
- A lot of my shared folders don't appears in Network (in Windows XP and Windows Vista)
- And 3 icons appears in Network of all computers : EGHN Qos Policy Holder DeviceEGHN Qos Manager DeviceEGHN QosDevice. [code]

View 8 Replies View Related

Linksys Wireless Router :: WRT54G - How To Access Setup Page

Apr 27, 2012

When I had DSL, my WRT54G was my DHCP master for my home network.  When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point.  But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again.  I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want.  The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
 
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server.  Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G.  This solved my problem:  my distant wi-fi computer now has a good signal, and both computers "see" each other.
 
However, now I seem to have lost access to the WRT54G setup "web page."  Is it possible to access the innards of the WRT54G when its DHCP service is disabled?  Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?

View 3 Replies View Related

Linksys Wireless :: WRT54G Firmware Update - Can't Access Router

Jun 28, 2006

I upgraded my WRT54G ver. 2 with the latest linksys firmware update (4.30.5). My previous firmware was 2. something. After the process i lost internet connection and i can't no longer access my router. I tried to reset the router to factory defaults by pressing the reset button for 10 seconds, but nothing happened. I also turned everything off and on again, but still nothing happened

View 7 Replies View Related

Linksys Wireless Router :: WRT54G Only Local Connection No Internet Access

Jun 23, 2012

I have some issue with internet connection and Router WRT54G. There is always "Local Connection" but no internet access. I checked that at two different laptops. One with Windows Vista and the other one with Windows XP. Both the same problem. There is a wireless connection with excellent signal strength but no internet access. I added a screen shut to see the Router setting. If more needed I will add more.

View 6 Replies View Related

Linksys Wireless Router :: WRT54g Can't Get Devices To Connect To Access Point

Oct 22, 2011

I have a WRT54g with Tomato firmware. I am trying to set up a WAP54g to extend the range but while that access point does show up as a network, nothing can connect to it. I already have the router's MAC address put in the WAP. I think the problem is that I have Tomato on the router and that conflicts with the default firmware on the WAP. Range isn't really the problem, I just need to strengthen the signal in a specific area that it's not getting to because of walls. I can't even switch to previous versions of Tomato anymore. I may have just bricked it.Some facts about my setup-My modem has default settings: PPPoE connection with a DHCP server enabled.-I set the router to use DHCP and put it in "Access Point" mode.

-The WAP is set to repeater mode and it was set to Static IP configuration by default. I simply followed the instructsions here: url....

-There are three different MAC addresses: The WAN, LAN/router, and the Wireless. I put the Wireless MAC address in the access point. Is that correct? 

-My desktop is wired directly to the router and it has a static IP outside the router DHCP's IP range-UPnP is enabled by default in the modem and router, but I'd like to try to get this working rather than buy all new equipment.

View 7 Replies View Related

Linksys Wireless Router :: WRT54G In Access Point Mode Impossible

Jul 18, 2011

I have a network with 2 WRT54Gs in it. One in the besement connects to my cable modem and serves as a gateway and DHCP server as well as a wireless access point. That WRT54G is perfectly accessible. I have another in my room set up as a router and access point only, connected by its ethernet port to the gateway. This one proves a bit trickier. Thet network works flawlessly, and if I couldn't see it sitting right there I would doubt it even existed. I can't ping it (I forgot the IP but tried all the ones that seemed logical), it doesn't show up in my network map, etc. From what I gather that's how a switch is supposed to work. But since this is also a managed router, I would think there should still be some way to connect to it to administer it. How can I log in to this router to change settings if I need to?

I'm not sure if maybe 192.168.2.0 is the other router or if that's some kind of special address (My network is on the 192.168.2.* subnet, don't even ask why...). I've seen it in other posts about routing tables but they all had it routing to 0.0.0.0 instead of the router's own IP. I tried pinging 192.168.2.255 and got no responses at all, not from any computers or from either of the routers, so that was not useful. Tracert from my computer to the gateway doesn't show the router (my computer connects to the gateway through the router).

View 4 Replies View Related

Linksys Wireless Router :: WRT54G - Password For Access Router's Web Utility?

Aug 10, 2008

I have tried multiple times to hard reset my Wireless G WRT54G ver.2 router, but have had no success. I held the reset for 15 sec, 30 sec, 2 min, etc and also tried holding it and then unplugging it and then plugging it back in. I've tried everything that I have seen suggested. My problem is that I don't know what the password is to access my router's web utility thing and I need to change the IP address. With every reset attempt, I hope that the default admin password will work, but sadly no.

View 2 Replies View Related

Linksys WRT54G Wireless Router - Forced Login On Previous Access Can't Be Removed

Oct 6, 2011

I've run into this before, but I can't figure it out this time. Running Windows XP SP3 on a Dell Vostro 1510 notebook with a Linksys WRT54G router wireless. Using Dells Network Assistant for management, so I cannot get to Windows wireless connection management directly.I have a connection to the internet with a Security Key. When I bring up a browser (Firefox or IE) I cannot resolve to a web site. There is a Cisco login screen that is forced. It's from a previous wireless connection on a different network at a different location.

View 1 Replies View Related

Linksys Wireless Router :: Setup Wrt54g As Access Point To Extend Signal?

Aug 17, 2011

how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
 
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved