Linksys Wireless Router :: WRVS4400N Site To Site VPN Drops After Time?
Mar 6, 2008
I have a new WRVS4400N configured with a site to site VPN to connect to my office. At the office, we're running a Cisco PIX 515E. I have successfully established an IKE preshared key and the tunnel is listed as Up. I can successfully connect through the VPN tunnel into the office network through the tunnel and all seems good. After some period of time, the tunnel apparently goes into a bad state. Access to the office network is no longer available. When looking at the VPN status screen, the Linksys indicates that the tunnel is up. However, I cannot ping any resources on the office lan. If I disconnect and connect the site to site VPN tunnel, it connects and comes back up successfully. It seems like there is some sort of timeout taking place here. I am running the 1.1.03 firmware.
View 7 Replies
ADVERTISEMENT
Feb 13, 2012
I have 2 WRVS4400n VPN routers configured for a site to site VPN and have an active connection between the two devices. I can ping all devices on the remote network and can browse them using ip's. I have an Win2k8 server on the remote network and have set my local dns to use that ip. I cannot browse the remote network using host names and am trying to add the local machine to the domain. I have the NETBIOS selected on the routers as well.
View 1 Replies
View Related
Oct 15, 2012
May I know can the 2 models WRVS4400N and RV042 perform site-to-site vpn with each other?
View 1 Replies
View Related
Dec 12, 2012
We have approx 40 branch offices - all of which are connected to a single core site over VPN Tunnels using various gear. At one particular site, we are having issues with the tunnel dropping sporadically throughout the day - some days it happens 10 times, some days it happens none. This just randomly started happening two weeks ago, without any changes taking place. Since it started happening, I have upgraded the code to latest versions, but still the issue persists. This particular site has a 2901 and connects back to a 2951.
Below is the output from:
debug crypto ipsec
debug crypto isakmp
[code].....
View 1 Replies
View Related
May 7, 2012
I am trying to set up a Site to Site between two RV042 with static IP at both routers.at the log at site 1 i get: packet from XX.XXX.XX.167:5: initial Main Mode message received on 10.2.32.1:500 but no connection has been authorized with policy=PSK.At site 2 i get: packet from xxx.xxx.xxx.146:500: initial Main Mode message received on 192.168.1.1:500 but no connection has been authorized with policy=PSK.I have tuned off the firewall and added a Port forwarding to the router ip and port 500.Tried with different autentication methods, but get the same message.
View 1 Replies
View Related
Mar 28, 2012
I am trying to create a site to site VPN using a cisco 2901 and Linksys router.I have the VPN configured and connected and I can ping gateway to gateway. However, from the Cisco I can't ping any of the devices beyond the gateway.Example, from the cisco I can ping 192.168.5.254 (gateway IP address) source gig 0/1 and it works great.
However if I ping from the cisco 192.168.5.50 (end user PC) source gig 0/1 it doesn't work.I have created a client VPN and that works perfectly.Below is my config.
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
!
crypto isakmp policy 2
[code]....
View 1 Replies
View Related
May 18, 2012
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies
View Related
Jun 17, 2012
We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies
View Related
Jun 13, 2012
The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
View 1 Replies
View Related
Oct 11, 2011
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies
View Related
Feb 7, 2011
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies
View Related
Mar 6, 2011
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies
View Related
Jan 27, 2012
i want configure VPN between backoffice which have ASA5510 firewall with static IP and site which have cisco router 1861 with dynamic IP.
how i can configure the site to site between them?
View 2 Replies
View Related
May 30, 2013
I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
View 9 Replies
View Related
Apr 2, 2012
hsrp+bgp+site to site vpn on router 2811.
View 2 Replies
View Related
Nov 8, 2012
My problem is VPN Site2Site between Cisco and Linksys routers: after a troubles vpn tunnel now seems up but no data is passed accross tunnel.This is configuration of Linksys RV042 (Firmware Version: 1.3.12.6-tm, seems last for this hardware [code]
View 1 Replies
View Related
Sep 25, 2012
Today i'm running with an ASA 5510 at the HQ and a ASA 5505 at my home address with a site-2-site VPN connection.
I'm only using the 5505 to hold this site-2-site VPN so it's a bit overkill. I would like a router at my home with build in access point, but it needs to support site-2-site vpn with the ASA 5510 at the HQ.
Are you aware of any Linksys routers that can hold this VPN connection, or is it only "real" cisco routers/firewalls where this is possible?
View 1 Replies
View Related
Mar 15, 2011
I have a Cisco 2911 router and a Cisco RV 120W router and i would like to establish a VPN tunnel between theese two. I have defined the settings on the Cisco RV 120W router and i just want the Cisco 2911 to follow those. setting up a connection with Cisco IOS.
View 1 Replies
View Related
Aug 22, 2011
I need to configure a site-to-site VPN using a Cisco 881 router on my end and connecting to an ASA5510 on my suppliers end.Our supplier has configured their end and I do not have access to their configuration.
They told us we have to NAT all inside address' to a single address (192.168.89.1) as this is the only one they will let through their firewall/tunnel.I know how to set up the VPN but not too sure how to set up the NAT part.
My sanatized config is attached. The code I am using to NAT my inside network to the single address 192.168.89.1, and send all traffic accross the VPN tunnel as this address is correct? With the router running this config the VPN tunnel does not connect.
View 2 Replies
View Related
Dec 15, 2012
I have an issue with 2 site to site VPN tunnels from a RV042G router. The issue is for both VPN tunnels is that in the logs, it is showing that when the RV042G router is trying to establish the tunnel, it is getting a response from the remote gateway internal address and not the Public address of the remote gateways. On the remote gateways I have other site to site VPN's terminating fine and the tunnels are passing traffic. I only have an issue with the RV042. On the VPN Tunnel page it shows for both tunnels waiting for connection. This is an output from the log of the RV042G
Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: sending encrypted notification INVALID_ID_INFORMATION to 203.43.XX.XXX:500 Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: Peer ID is ID_IPV4_ADDR: '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: we require peer to have ID '203.43.XX.XXX', but peer declares '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: we require peer to have ID '203.43.XX.XXX', but peer declares '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: sending encrypted notification INVALID_ID_INFORMATION to 203.43.XX.XXX:500 Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: Peer ID is ID_IPV4_ADDR: '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: we require peer to have ID '203.47.XXX.XX', but peer declares '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: we require peer to have ID '203.47.XXX.XX', but peer declares '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: sending encrypted notification INVALID_ID_INFORMATION to 203.47.XXX.XX:500
VPN tunnel terminating on 203.43.XX.XXX is a Checkpoint firewall running R70 software version?VPN tunnel terminating on 203.47.XXX.XX is a Cisco ASA 5510 running ASA 8.2.4 software?As stated above, I have other VPN tunnels working fine. This RV042 is a replacement router as the original router suffered a power surge.
View 1 Replies
View Related
Mar 31, 2011
Just now my boss asked me to prepare to set up site-to-site VPN on Cisco 881 Integrated Services router to ASA 5505 router which is now running at the HQ side. I am now learning pdf file from Cisco which mention how to setup site-to-site VPN between Cisco 1812 IOS router and ASA 5505 router by using ASDM V6.1 and SDM V2.5. Can't find the paper for that Cisco 881 device.
View 4 Replies
View Related
Dec 12, 2010
I have Cisco 877 routers, with ethernet (LAN) and ADSL (external) interfaces. The ADSL interface gets dynamic IP. Is Site to Site VPN with Dynamic IP and Internet Browsing Possible on the Same Router.
View 4 Replies
View Related
May 27, 2013
I'm setting up a site-to-site VPN between two offices, Site A uses a Cisco RV110W VPN Router with a static WAN IP and local IP 192.168.1.0/24 while Site B I have set up with a Belkin N300 VPN router which also has a Static WAN IP and the local IP is set to 192.168.2.0/24
I'm able to ping from Site B (192.168.2.xxx) to Site A, however I can't communicate from Site A back to Site B.how I could go about troubleshooting this? I've been scouring the internet for 3 days trying to get to the bottom of this with no luck.
View 3 Replies
View Related
Jan 13, 2012
I have recently bought two CISCO routers RV220W for our main and brach office mainly for VPN tunneling. I didnt know they are routers only not modems. so I have set it up using BT 2wire Router as modem only.
I have successfuly setup the routers and manage to establish the VPN tunneling between two routers. AS bt doesnt give static WAN IP address so I have used Dyndns which works fine. although I have 5 static ip address which cannot be used for WAN unless i cahnge to one IP address even then BT tech said it will not work.
when I created the tunnel i could ping both servers with their IP only not with the names. I can ping them fine locally. I could also see the network from branch office to main office but not from main office to branch office. today when I restarted the server I cannot ping both server i mean vice versa but VPN tunnel is established. now I cannot see the network from branch office to main office as well.
Both sites running windows server 2008 standard. main office server has 6 NIC cards two wwith public and three with private ip addresses, its also runing Terminal server, exchange, file etc. the branch office has two NIC card one with private and one with public ip. Intially I could establish the VPN tunnel as the network range was same on both sites so I changed one in th e10.0.0.0 range other in 192.168.1.0 range and VPN tunnel was established straightaway.
As soon as the VPN tunnel was created I manage to creat an external trust without any problems and both servers are added in each other forward zones as name servers.
in the main office the fues went off and I had to re-start the router and now the VPN tunnel is not establishing, mainly the error is ISAKMP-SA Expired I will paste the log of both routers below
1. How to Clear Old or Existing Security Associations (Tunnels) on RV220W
2. how to fix the problem where I can ping the server with their IP as well as domain names ?
3. how to set it up so that both sides can see the network resources as well as access it ?
4. how to set it up so if the staff in branch office wants to log on the domain in main office he can simply do it as he does it in his office.
View 7 Replies
View Related
Nov 14, 2012
how to configure a site to site tunnel using IKEv2 between our offices using an ASA 5515-X and a Cisco 3925 router running IOS 15.2 Connecting ASA to ASA and ASA to Router via IKEv1 works fine. Want to take advantage of the improvements in IKEv2 but I'm having difficulty with the ikev2 setup on the router. Here is the pertinent ASA side config--
ASA IP: 5.5.5.5
Router IP: 10.10.10.10
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1
[Code].....
View 1 Replies
View Related
Nov 29, 2011
I was traying to make a site to site VPN between a cisco 1800 router and cisco asa 5510. But it was impossible to get it. [code]
View 1 Replies
View Related
Jul 6, 2012
how to configure a site-to-site VPN between RV042 router and 1941 router?
View 0 Replies
View Related
Jun 11, 2012
I'm setting up site to site VPN on a RV110W router. The administrator guide site to site instructions don't match the options on the router.The first step tells you to click on VPN then Basic VPN Setup. The router under the VPN option only has three choices, (1) VPN Clients, (2) Certificate Management and (3) VPN Passthrough. I have upgraded to the latest firmware 1.0.0.9.
View 4 Replies
View Related
Sep 9, 2011
what is going on message" MM_NO_STATE ". i'm not clear about this for documents they said that MM_NO_STATE-The Internet Security Association and Key Management Protocol (ISAKMP) SA has been created but nothing else has happened yet."but i still don't know that is the main problem? Note: i used Cisco router 2821 and Cisco router 1841 ( and configure VPN site to site)
View 4 Replies
View Related
May 26, 2011
I'm looking to configure a DMVPN spoke with a Site to Site VPN Connection to a different destination than the DMVPN. I'm using a Cisco 2800 router. When I add the crytpo map to the outside interface for the Site to Site VPN. The DMVPN drops. Is there something I could be missing? The Tunnel interface for the DMVPN has the shared optioin applied to the tunnel protect ipsec profile.
View 6 Replies
View Related
Aug 30, 2011
I have a remote office with a dual WAN router (2911) in front of an ASA (5510). Our main office currently has an ipsec site to site vpn to that remote office ASA. The router has two ISPs. ISP-A is the wan link used for the site to site and has provided us with a /28 public address space which we use on the ASA outside interface for the site to site. Now we are in the process of getting a second ISP which will also provide a /28 or /29 public address space. I would like to use that second ISP for backing up the site to site in case ISP-A link goes down. I think I have the IP SLA config worked out. My question involves NAT. On the router I would like to configure a static nat that only takes place if ISP-A goes down. In other words, if everything is working fine, then the router does not nat the ASA outside address, but if the ISP-A link goes down, then the router will NAT the ASA outside address to one of ISP-B provided public addresses.
View 6 Replies
View Related
Feb 20, 2013
I have two Cisco ASA routers and I have a site to site vpn set up between the two. The VPN link works but Site A can't ping anything on Site B. Site B can ping Site A. Site B can ping other pcs on it's own network. Site A has been in place for a while and has other site to site VPNs that work fine, so I think the problem is with Site B. Here is the config for Site B:
Result of the command: "show running-config"
: Saved
:
ASA Version 8.4(4)1
!
hostname SaskASA
enable password POgOWyKyb0jgJ1Hm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
View 6 Replies
View Related
Nov 25, 2012
I have an offsite employee at an apartment complex where she uses the leasing offices internet connection. I have an ASA 5505 but I don't know how to make this work behind the leasing offices router and other network equipment. Is there any way to have her connect back to our corporate network using site to site vpn without touching the leasing office devices? She needs VoIP and corporate server access.
View 3 Replies
View Related
