Linksys Wireless Router :: WRVS4400N Can Work Route All Traffic Through?

Oct 6, 2011

i want to set WRVS4400N Route all traffic through
 
it function as same as sonicwall Route All
 
[URL]

View 1 Replies


ADVERTISEMENT

Cisco Routers :: WRVS4400N Can Work Route All Traffic Through

Oct 5, 2011

i want to set WRVS4400N Route all traffic through, it function as same as sonicwall Route All.

View 1 Replies View Related

Cisco Wireless :: WRVS4400N Won't Route All Traffic Over IPsec

Dec 15, 2011

All of my remote sites use various routers to route all of their traffic via IPsec.  However, I have one WRVS4400N w/firmware 2.0.2.1 configured with a working tunnel.  My issue is I need to set the Remote Group to 0.0.0.0 0.0.0.0 so all traffic is forced via IPsec tunnel and not out the local gateway.  When I do the error, Remote Security Group and Local Security Group cannot be in the same network. However, it works with Cisco/Linksys RV042.

View 3 Replies View Related

Linksys Wireless Router :: WRVS4400N Setup - How To Get WDS To Work

Aug 29, 2011

I have a WRVS4400N setup as a main router for one of our bays.  For wired connections it is working with no problems.  When I first installed it it ran fine for wireless as well.  I was trying to get WDS to work and at some point the wireless stopped working.  My laptop can no longer connect to it and often cannot see it when doing a scan for networks.  I have already checked that it isn't a problem with the laptop, that there are not other networks causing interferance, and even tried resetting to default configs.

View 1 Replies View Related

Linksys Wireless Router :: WRVS4400N Single Port Forwarding Doesn't Work

Jul 1, 2012

Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again. 

View 1 Replies View Related

Linksys Wireless Router :: BEFVP41 - How To Route Traffic Through VPN Tunnel

Nov 10, 2007

I have set-up a Linksys BEFVP41 VPN router at home (192.168.1.1 / 255.255.255.0)

View 7 Replies View Related

Linksys Cable / Dsl :: X3000 Does Not Route Traffic Between Its Wired And Wifi

Jan 31, 2013

The X3000 functions as a router/gateway between the ADSL network, its wireless network (WPA2) and its wired network. After a cold start, factory reset and restore of the config file everything works fine. I have interconnection between all three parts of my network. However after ± 24 hour there is no connection possible anymore from the wired to the wireless network and vice versa. A normal power off - power on will not work. The only thing that works is running the factory reset procedure as discribed above. I changed the MTU to manual 1400 as was suggested on this forum, but that does not work. Apart from this issue, ADSL is hicks sometimes. From my ISP I heard that at certain times my router issues ten's of DHCP requests within one minute, while the connection (modem) remains perfect. I have the impression that after such a DHCP request storm to my ISP, the interconnection between my X3000 wireless network and my X3000 wired network is lost.

View 4 Replies View Related

Cisco WAN :: 1921 Router Won't Route LAN To WAN Traffic

Feb 18, 2012

The router passes the Interface test for the WAN port in CCP but it still we cannot access the internet.  Here is my configuration:
 
Building configuration... 
Current configuration : 3663 bytes
!
! Last configuration change at 09:29:52 Chicago Mon Feb 20 2012 by fbcpekin
version 15.1

[Code].......

View 5 Replies View Related

Cisco Routers :: WRVS4400N Default Route

Feb 26, 2013

I bought a WRVS400N v2 to be used as an access point. Currently it is hooked up on my switch via a trunk port and is able to communicate with my gateway. Whenever I try to access an IP subnet other then the local IP address of the WRVS, I get a network unreachable error. To fix this for my local networks, I added the appropriate static route to cover my local LANs and that seems to work now. I tried to add route 0.0.0.0/0.0.0.0 using the web interface for internet access, but somehow it does not recognize this as a default route (quad zero!?). Does any know how I can set the default gateway in this router? Maybe, but hopefully not, I have to use the WAN port to create some kind of uplink and use one of the LAN ports to connect using the trunk port and route traffic for the clients over the WAN port .

View 1 Replies View Related

Linksys Wireless Router :: Use WRVS4400N As Gig Switch Only?

Jul 19, 2012

I have 2 WRVS4400N's  availible to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.

View 1 Replies View Related

Linksys Wireless Router :: Wrvs4400n PCI Compliance / How To Set

Jan 13, 2012

I'm keep failing my pci compliance test I have a wrvs4400n and I keep getting "firewall udp packet source port 53 ruleset bypass" i've blocked port 53 but keep getting rejected. How to set the router?

View 1 Replies View Related

Linksys Wireless Router :: VPN Connection To Wrvs4400n With Mac?

Feb 26, 2007

I would like to connect to the built in accounts on the wrvs4400n from a mac VPN client. I am new VPN and have not found much information on how to establish this connection. Since Linksys seems determined to rely on Quickvpn, and provides no information on what it is actually doing under the hood I can not figure out how to configure any of the VPN clients available, or the built in VPN tools, for OS X (10.4.8). The only information I have been able to find seems to relate to setting up VPN Tunnels, or running a server behind the wrvs4400n and using one of the VPN passthrough options. I would like to connect directly to the built in accounts, how to set this up on a mac?

View 7 Replies View Related

Linksys Wireless Router :: WRVS4400N / Automating (check Vpn) Through C#?

Apr 27, 2012

I would like to automatically check if the VPN is up or down, simple enough, and respond by bumping it, disconnecting and connecting, as needs be (not so simple I think).This through a C# program using HttpWebRequest and HttpWebResponse.It's simple enough to login to the VPN page using known credentials. Done deal. And also very easy to check a couple of known patterns in the VPN table.When I determine I need to bump the VPN, how do we simulate the form submission and/or call to the JavaScript programmatically?  we're using a Linksys WRVS4400N router, firmware version V1.1.13.

View 2 Replies View Related

Linksys Wireless Router :: WRVS4400N Can't Connect To Internet

Feb 26, 2012

I cant get the WRVS4400N to connect to my cable modem. The WAN link light isnt even lighting up. Im wondering if this unit is bad out of the box. Is there a setting im missing to get them to talk to one another. This is no mention in any of the manuals.
 
Connections: - The "Internet" port on the WRVS4400N to the "Network" port on my cable modem (No link light)
 
Here is what i have verified at this point: - My old router connects instantly to the modem when plugged in (Same cable) - When i plug my laptop into the WAN port on the WRVS4400N i get a link light. When i plug the modem into the WAN port...nothing. 

View 1 Replies View Related

Linksys Wireless Router :: IP Address Conflict Using Wrvs4400n?

Jan 24, 2013

I get a "IP address conflict" message on my wireless network. Using a WRVS4400n wireless router with the latest firmware that is set to PPoE. Motorola 336 dsl modem is set to bridge mode. My network has 2 computers attached: hardwire desktop and wireless connection to laptop. When I contacted ATT support, they said the problem is in the wireless modem. Are there some settings in the WRVS4400n that must be set to insure that each computer gets a different IP address?

View 2 Replies View Related

Linksys Wireless Router :: Block An IP Address With WRVS4400N?

Nov 8, 2009

I've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's.  I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?

View 3 Replies View Related

Linksys Wireless Router :: Connecting A WRVS4400N To A Dell Switch?

Feb 10, 2012

The router will serve as an access point for 10 wireless station, 6 of them will run over Terminal server, the router will also serve 20 computer for the internet, so I want to Link aggregate the four LAN port to my swtich, I know how to do it on my Dell Powerconnect, but I want to know if the WRVS4400N will support it, there will be a lot of traffic going through the router so linking the 4 port in LAG mode to my Powerconnect swicth will speed up the communication

View 1 Replies View Related

Linksys Wireless Router :: WRVS4400N Firewall Blocking VPN Pass Through

Jul 13, 2011

I cannot connect via VPN PPTP (normal setup in windows xp), I have managed to connect over VPN direct connected to internet, through the router (WRVS4400n) if I turn off the firewall. But I cannot connect with the firewall enabled,One more thing, the device is on and I have enabled the passthrough (and 'Multicast Passthrough' in firewall basic settings) for all available options where one of the options is PPTP.

View 1 Replies View Related

Linksys Wireless Router :: Can't Find Setting On This Cisco WRVS4400N

Mar 12, 2013

I am attempting to setup a router with another vendor, but I am not wanting to give full access to the network just a couple IP addresses, most routers you can setup an VPN IP Range, but I can't find that setting on this Cisco WRVS4400N.

View 1 Replies View Related

Linksys Wireless Router :: WRVS4400N Can Get Any PING To Complete VPN Connection

Jan 14, 2012

I bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the QuickVPN Clien for connecting to my home network.My home network is connected to a pre provide by my ISP Thomson and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analysing the log you can see that I can get any PING to complete the VPN connection. [code]

View 1 Replies View Related

Linksys Wireless Router :: Xbox 360 Slim Won't Connect To WRVS4400n

Jul 23, 2011

As a temp work around I have two SSID now, one for everything else running WPA2 and one for xbox running WPA. The xbox seems to not like the router on WPA2 and though this would make one think, oh its your xbox, thats not always the case with devices. Some just may happen to want to use a feature the device doesn't support correctly and other devices are able to work around it while ones not so I cant for sure blame on xbox.

View 1 Replies View Related

Linksys Wireless Router :: WRVS4400N Breaks VPN Session During Https Connection?

Oct 6, 2011

here comes the incident description: WRVS4400N breaks established VPN session if I am trying to connect to any LAN host via HTTPS.

View 1 Replies View Related

Linksys Wireless Router :: WRVS4400N Port Forward Is Not Working To FTP Service

Feb 17, 2012

I've been configured my device to forward FTP service to my server, however, I can't access this service outside from my network. I used Single Port Forward and not worked, after, I've used Port Range Forwarding starting in 20 to 21 and not work again.I've sniffed my computer and I've found just 3 outsides packages without response.I've tried with directly IP ADDR and DYNDNS ADDR, but neither one or other worked.

View 1 Replies View Related

Linksys Wireless Router :: Wrvs4400n - All Computers Can Access Printers (Port 3)

Jun 18, 2008

I have a linksys wrvs4400n router on which:The wireless computers are connected to the home network (v lan 1)Port 1 is connected to the home network (v lan 1)Port 2 is connected to the office network (v lan 2)And the printers are connected to port 3.Now I'd like to setup the router in such a way that all computers have access to the printers (port 3), but I don't know what v lan settings I have to use on port 3, or if it is even possible...

View 5 Replies View Related

Cisco Routers :: Airplay Won't Work On WRVS4400N?

Apr 7, 2013

Apple AirPlay won't work on AppleTV (from neither computer nor iPhone) with my new Cisco small busines router WRVS4400N.  It was working just fine on old consumer level linksys router. I have spent 3 hours with Apple support to no avail.  Apple TV works fine on internet functions (netflix, YouTube, etc.) and I can play music and videos from the cloud, but iPhone and computer can't connect to AppleTV even though the icons appear in iPhone and Computer... just can't establish a connection.

View 2 Replies View Related

Cisco Routers :: WRVS4400N - VPN Tunnel Up But No Outgoing Traffic?

Jan 29, 2012

we've buyed a WRVS4400N to create a IPSEC VPN tunnel to our client in order to access some applications.
 
After a while trying to configure the router, we have archieved it and the VPN tunnel is up. We can see the tunnel up from here and from client's side as well.
 
Our client supposendly have created the tunnel in order to access a list of specific IPs in the range 10.113.x.x, but if we try to access this IPs via telnet whe cannot obtain any response.
 
Making a tracert, we obtain...
C:UsersHuexxx>tracert 10.113.56.177
Traza a 10.113.56.177 sobre caminos de 30 saltos como máximo.
1     1 ms     1 ms     1 ms  192.168.0.1
2     *        *        *     Tiempo de espera agotado para esta solicitud.
3     *        *     ^C
 
... and therefor the client doesn't receive any packet at its firewall.
 
I've tried to establish a static route for 10.0.0.0 255.0.0.0 to their remote gateway, but I'm unable to add any entry to static routing list... The router tries to do something, but afterall I cannot see the new entry...
 
What can I do to route the traffic through the tunnel?

View 1 Replies View Related

Linksys Wireless Router :: WRVS4400N - Laptop Gets Battery Power / Network Getting Packet Loss

Jul 24, 2011

So I have an WRVS4400N V2 and just got a new laptop with an Intel 6230 Wifi card in it and have an odd problem.While the laptop is on battery power the network gets massive packet loss.

I don't know what to do.Laptop manufacture says its AP but AP worked fine with old laptop and works fine when laptop is on power and all other devices seem to be fine with the exception of my Xbox 360 that wont connect if I have it on WPA2 but I will post another thread for that.

View 1 Replies View Related

Cisco Routers :: WRVS4400N V2 And IPv6 Traffic Bridge Between Wi-Fi And Ethernet?

Jun 9, 2011

I have on my ethernet linux box, that is responsible for IPv6. This box is configured as IPv6 gateway from my network and it also sends RA to the network. All devices on ethernet network can work on IPv6 without problem. Clients, that are connected to WiFi, they just receive the RA from this box -> this packet is sended over WRVS4400N to the wifi network. But all other traffic do not pass the WRVS4400N, so the wifi client is not able to ping the IPv6 gateway. There is no problem on IPv4, there the wifi client is able to communicate with any ethernet device.I have tested WRVS4400N setting "ipv4 only". If I switch on "ipv4 and ipv6", than all devices will get some additional IPv6 adresses and the communication from WiFi client to IPv6 router is not working again. How to configure the WRVS4400N to bridge all IPv6 traffic between WiFi and ethernet?

View 2 Replies View Related

Cisco Routers :: WRVS4400N - Server Certificate To Get VPN Client To Work?

Dec 12, 2011

WRVS4400N Where is the Server Certificate located to get the VPN Client to work?

View 2 Replies View Related

Cisco Routers :: WRVS4400N V2 Default Password Doesn't Work

Aug 6, 2011

I upgraded the firmware for my WRVS4400N v2 to version 2.0.2.1 firmware, now old and default passwords don't work. I have tried resetting it as well, and the default password does not work.

View 1 Replies View Related

Linksys Wireless Router :: Static Route Between Two WRT160NL?

Sep 12, 2011

I have my internet connection connect to my main Linksys router WRT160NL (192.168.1.1) with 192.168.1.x.My 2nd Linksys router connect to the first one as Gateway as well.The 2nd router has its WAN ip of 192.168.1.100 and it's local subnet as 192.168.2.x.My machines at 192.168.2.x can get to the internet and connect to all machines in the 192.168.1.x network.However, the 1.x network can't access the machines on the 2's network. And because of that, i can not sharing or printing between two network.I try to add static routes on my main router (192.168.1.1) with the route: 192.168.2.0 mask 255.255.255.0 and defaute gateway 192.168.1.100However, the route not work still.anyway to make sure that the 1.x network able to access the 2.x network and from 2.x   access 1.x for sharing files and printing.

View 1 Replies View Related

Linksys Wireless Router :: WRT54GL Which Route Does Data Take

Nov 5, 2012

I've a WRT54GL still working well after 5 years of use. I've got one Ethernet cable attached PC (computer "A"), and two WI-FI attached, (computers "B" and "C"). They're all running Windows XP. I've heard much about how intelligent devices and intelligent systems can route the traffic in the most efficient manner, but not sure how or when it works. For example, if I sit at computer "B": and copy (or move) a file from computer C to computer A, what route does the data take? Does it pass through computer B?

View 1 Replies View Related

Cisco Switching/Routing :: 3825 ISR - Traffic Route From Switch Port To Router Port

Jun 5, 2013

I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level.  I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other.  I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it.  This seemed to allow devices connected to the switch ports to talk to the built-in router ports.  I thought this was all making sense until i applied an access-list to the router port.  It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere.  I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port.  However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully. 

It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other. 

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved