I'm trying to change my username and password, but I don't know how. The manual is in Japanese, so I don't understand, what I need to do.
I have a wired router that seems to be on 192.168.1.1. When I installed the wireless router for the first time, I connected without cable, that may be the problem about the DHCP Server, but I don't know. Anyways, these IP don't work:
I don't get any access and therefore all my neighbors can use my connection right now. But the router itself works fine from the start.
i am using a D-Link 2730u, was trying to change the username and password for the router but it keeps saying that ACS URL is required, there is a place where i can put one but even after goggling it for a bit i didn't understand what should i put in there?
i forgot to change the default username and password of 1941 router. I have alos performed WR memory on router. When i am trying to recover it through ROMMON mode i am not getting the initial configuration Dialouge through which i can change the password . I have gone through all documents available through internet for recovering the same but unable to recover it.
I have tried to change the username and password using the following procedure but when I do so and reboot the router and try to login using the new userid and password it says Authentication failed. Complete these steps in order to recover your password:Shut down the router.Remove the compact flash that is at the back of the router.Power on the router.Once the Rommon1> prompt appears, enter this command:confreg 0x2142Insert the compact flash.Type reset.when you are prompted to enter the initial configuration, type No, and press Enter.At the Router> prompt, type enable.At the Router# prompt, enter the configure memory command, and press Enter in order to copy the startup configuration to the running configuration.Use the config t command in order to enter global configuration mode.Use this command in order to create a new user name and password:router(config)#username cisco privilege 15 password ciscoUse this command in order to change the boot statement:config-register x2102Use this command in order to save the configuration:write memoryReload the router, and then use the new user name and password to log in to the router.
The wireless router PW has been changed, I got the new one correct but upon entering it on my laptop it goes around circle showing,"Wireless network detected" and then,"Unable to connect to preferred wireless network"It never works. I don't know how to fix this problem. It did not happen on my iPad.
I have a problem with my linksys WRT54GL router. I entered here [URL] and i set it up, i can connect to internet on my PC and wireless works great but i can't set wireless password and name. When i go to the wireless tab, i write the new name but when i hit seve setting i get disconnected from internet. I try to go to status and click on Connect tab, when is connected internet works but the name and the password of the wireless that i set earlier is reset to default. What do i have to do to set name and password and have internet at the same time.
I am trying to figure out my WEP code to use to connect to XBOX LIVE. To log on to my internet we just have a WPA-Personal I think, so I have been trying to sign into my router to hopefully obtain my WEP key there, but cannot sign in. I have tried every combination of usernames and passwords such as:
I have tried using my router name and password when you 1st connect and got nothing.I have held the reset button for a minute straight to try and restore default settings and have got nothing. I'm trying to enter my ISP into the web browser
I'm not a very knowledgeable person when it comes to networking stuff so ill try and explain this the best I can.I have a Cisco router the number on it is EPC2425.I set a user name and password I've long forgotten for access to the web based security protocols for the modem and if there was one I've lost the disk for the control protocol program.I need to get to the port forwarding a such on there and I have no way to a present.
I just dug my router (wrt54g) out of the closet and hooked it up but I cant remember my name or password for the router. Is there anything I can do that doesn't involve paying linksys any sort of "fee"
I'm moving from an 1801W to an SRP547.My adsl supplier (BT) has given me a username and password, and also a router IP address, a subnet and an gateway IP address. I have 13 fixed IP addresses. I don't speak cisco, so I'm using the built in interface to configure it.If i choose IPoA I can enter the IP settings. If I choose PPPoA I can enter the username and password.I do not see anyway I can enter both the IP settings and the username + password on the WAN configuration page.
I use an internet network via wifi that require username and password. The router for wifi network in my place and i connect my cisco(linksys wrt320n) to the router. Every time i want to connect to internet i have to enter my username and password.I try to configure my cisco modem but there is no result. Is there any way or program to automatically enter the username and password?
I get into the router ok, using no username and "admin" for password.I set up the key, hit OK, then when I hit "apply" the prompt comes up for the username and password again. I skip the username, enter "admin" for password (just like I did getting into the setup earlier) except now it says it doesn't recognize, or it's invalid, etc.
I successful set up my WRT54GR router. Now I want to add a new device but can't find or remember my user name and password. So I decided to reinstall the router only to find that the http://192.168.1.1 page asks me for my admin password - having sensibly created one 4 years ago which I have now forgotten or where I wrote it down. How the hell do I get around this - if at all or do I have to buy a new router and start all over again!
The EA4500 web-settings application asks for a username and password. The username is "admin" and the password is my long (60 character) wpa key. I see where I can change the password but it says I'll lose all wireless connections. This doesn't make sense to me. I would think the router administration username and password are completely separate from the ssid and wpa key. This was the case with my earlier LinkSys router. I'd like a router administration username to be something other than the generic "admin" and a password that is easier than my long wpa key. I want a separate ssid and wpa key (what I currently have).
I want to upgrade the firmware for the router wrp400 , i am asked Username & Password in order to update the firmware.I tried admin/admin does not work. I tried to reset the router, same thing, I have no ISP user and password.
I changed my E1000 router name successfully, and then went into the Administration section to change my password. After changing the password and clicking on Save a small screen pops up asking me to verify my router's username and password. When I enter the exact same user name and password it does not accept them. When I try to enter the old user name and password it does not accept them either. I then try combinations of the two and it still will not accept the input. I have reset my router 4 times now and this keeps occurring. I am completely baffled.