Routers / Switches :: Connect 2 Wireless Routers Together
Jan 21, 2013
I am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one
How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
I have a laptop connected to a net gear wireless router (for internet), but I am very close to buying a Belkin network USB hub to make my hard drive wireless, but this requires a router. I do not want move my hard drive to where my net gear router is, so I need to get another router, i am looking at a Belkin router so that I can make my hard drive wireless (This is the only reason for the router, it will not be used for internet) so I can keep my hard drive in the same place.
I have a Netgear WGR164v9 wireless router connected to internet directly by public IP and this router performing DHCP for wireless LAN ip subnet is 192.168.1.x. A server (DNS,DHCP & RRAS with NAT) connected with this router by ip 192.168.1.6 which has another subnet 192.168.10.x for LAN PCs. In this situation everything is fine like internet browsing. The only problem is wireless PCs (192.168.1.x) can't connect with wired LAN PCs (192.168.10.x). The router ip is 192.168.1.1. How can I configure to connect those two subnet's PCs?
If your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
I have a wireless router at home and i have a PC and a mac enabled for it. I have recently bought an IPAD and i can't connect for some reason. When asked for the password it doesn't enable me to connect so I'm worried that i've forgotten my password.
I changed my netgear wireless router password and now my laptop will not connect to the router or to the internet. It has no popup to put the new password. I have no problem logging on with my phone...just the laptop.
I just bought a sony vaio laptop and I can't connect to the wireless network, it appears back and forward a message saying that the adapter is not found and then it says it is working and then it is not found again and so no.. Tried to connect the laptop using the WPS button but it did not work either.
How do I use an Actiontec 1000 modem (with wireless) and a TP-Link 4 port cable/DSL router and still have a wireless signal? When I connect the ethernet from the modem to the router, the router lights come on but the wireless signal goes down. Want 2 PC's wired (only one port on modem) and still want wirelss signal.
The first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.
I have a wireless router that was named and all the wireless equipment (laptop, ipod, phones) was connecting easily with no problems. Everything is saying "unable to connect". I have no clue what she did but she said her laptop asked her for the 8 number code from the router and she entered it.
my computer will connect wired to internet and can find the wireless connection but wont connect. my wireless icon flashes intermitently and my mobile will work via wifi. do i need a new router this one is a G wireless Modem router Belkin had it for about 4 years?
I have high-speed cable access currently coming into an older D-Link 4-port wired router. I need to buy a new wired and wireless router so I can sync my new Android 4G phone (I'm in an area with bad cell coverage but I can sync with wi-fi). I have a second house about 200 feet from mine and have 3 Cat5E lines running underground in conduit to it so the lady next door and and her two kids can use the internet (I have 40-50mb service for my business use at home). Problem is that my kids have discovered YouTube, streaming video, video chat, etc. and are burning up my bandwidth. I currently have two of the lines to them disconnected so that I can limit their use to one computer at a time. I'm considering having them buy a Wireless Access Point, can they connect it to the standard single Cat5E LAN wire that is coming from my new wired and wireless router when I buy it?
I installed DD-WRT on my router and placed it in bridge mode, configuring it with what I thought was my Androids IP address for the gateway. I tried with the Android IP address identified through cmyip.org, 184.108.40.206, and with the one identified through ipconfig command, 192.168.43.1. Neither address was successful. Also, I am unable to access my router using the IP address that I manually assigned to it.provide some assistance on the process of bridging from an Android to a wired PC through a router, Linksys WRT54G v3,
I have a Netgear N300 Wireless Router (WNR2000), and I am trying to connect the internet through it. The internet light stays amber, and though the router recognizes it, I can not connect to the internet. My computer also doesn't seem to recognize the router at all. Installation CD will not work either.
I am trying to portforward so I can host a server of a game I play, but whenever I try to connect to my default gateway it just times out and cannot load.I have done the cmd -> ipconfig/all and I found that my default is 192.168.0.1What do I do
I recently moved out of state and have been working remotely. I just got a new internet provider who will not let me connect to my office VPN without a small business account which is ridiculous. I've been reading up on how to work around this and haven't been able to figure anything out. I've signed up for a dynDNS account but the truth is I have zero experience with this and don't know what I'm doing - most of the stuff I'm reading is a foreign language to me. I can log into my router and change settings and I can get VPN info from my tech person and work so I just need to know what to do. I can't really work effectively without access to my network but I refuse to pay for a small business account
I'm trying to access 192.168.0.1 to configure my linksys router to add new hardware to my home network but my browser (Safari) can not open the page - error message suggests 'server where this page is located isn't responding.
with a networking issue that I'm having with the 2nd computer I have trying to connect to the interntet via my Westell 7500 DSL router. I ran the diagnostic tool on the NIC to make sure it working correctly and it is, and so is the cable according the tools; I also verified that myself via unplugging/plugging the cable into the router and it detects eachMy other 2 computers work fine via the router.Here is the ipconfig info;Host Name:XXXXXXPrimary Dns Suffix: (blank)Node Type: HybridIP Routing Enabled: NoWINS Proxy Enabled: NoEthernet Adapter Local Area Connection:Connection-specific DNS suffix: (blank)Description: Intel(R) 82562V-2 10/100 Network ConnectionPhysical Address: 00-1D-09-8D-34-3BDHCP Enabled: Yes
First , I have installed the router and modem correctly , and i connected it to the switch , So the other devices connected to the internet but not connected to the workgroup so i can't share the files between the PC's ? Modem >>> Router >>> Switch >>> PC's
I have a Belkin Wireless G Plus MIMO Router and had no problems connecting to corporate in the past until several months ago. I can connect just fine if I bypass the router and connect to the modem. I also have no problem if I go to places like Subway. There is no problem with the wireless internet connection, only a problem when I try to connect to corporate through the VPN.
I have 4 computers on LAN using a router and I cannot see eachother, don't know how to configure the PCs. The router is set on DHCP for LAN, the PCs are using Windows 7 and can connect through the internet the router is providing (4 dells) but don't know how to set the computers to see eachother and to share files.