Setup Coax / MoCA / WRT45G Second Access Point

Jan 28, 2013

I don' know how to setup the LinkSys WRT45G (v2) router properly for the way I want to have things wired. I have Verizon FIOS in basement with MoCA enabled coax line going into a splitter, running lines throughout the house. The main router (Actiontec MI424WR) is on the first floor, east side of house connected by coax and the area I want to put the second access point (LinkSys) is on the second floor, west side of house. So very weak wireless signal where the LinkSys is at. I used a Actiontec Verizon Coaxial Network Adapter to plug into the coax outlet in the 2nd floor room. Then run an ethernet cable from that unit to a older LinkSys router WRT45g (v2). I wanted this router to provide a wireless access point and also a place to plug a Sonos unit into. On the back of the router is the usual RJ-45 port and the 4-port switch. I have the line coming from the moca adapter (source) going into port 1 of the switch, the Sonos 5 plugged into port 2 of the switch. I am able to connect and control the Sonos units about 50% of the time like this, but sometimes nothing can be found. I believe this is because my phone can not connect to the wireless when I am upstairs, anotherwards the LinkSys router is not working right. If I plug the ethernet cable from the MoCA adapter into the RJ-45 interent port (like I think it should be, since it is the source), then nothing works.Also, I do not know if the router is functioning as a wireless access point, I am suspecting it is not.The router still has stock firmware, has DHCP disabled, the security and SSID identical to the primary router.

View 1 Replies


ADVERTISEMENT

Linksys Access Point :: Using Coax To Feed AP Lap 1142s?

Apr 14, 2011

Got a customer who is considering using 1/2" plenum to feed APs instead of twisted pair.  The coverage target is a medium traffic office space with a focus on voice, data and video.  Are there any concerns in using coax rather than twisted pair?

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Setup After A Reset?

Jul 9, 2006

I had to reset my access point but the login screen fails to appear to lock the router.  I don't have the setup wizard disk.

View 9 Replies View Related

Enterprise Media Converters For Coax To Ethernet And Ethernet To Coax?

Feb 23, 2011

I work for a place that has its own TV broadcast system. From the central site we have contracted fiber connectivity to each of our 10 remote locations. To each location we currently have fiber for data (1Gbps) and fiber to transport our TV channels. Am am looking for a device that can take in our TV channels on coax and give me an rj45 ethernet connection so I can plug the unit into a data switch to use our data fiber for everything (if I need 10 units at the central site to do this, that is fine).taking the ethernet back to coax to distribute TV to all of the TVs in the building. This would eliminate me 10 point to point fiber links.

View 6 Replies View Related

D-Link DIR-655 :: How To Access Setup Window When Used As Access Point

Jul 3, 2011

I have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?

View 4 Replies View Related

Linksys Wireless Router :: WRT45G Version 7 Reboot When Want To Access In Web Base Utility

Sep 22, 2011

i have router  WRT45G ver 7 it work but when i want  to access in web base utility the router reboot

View 4 Replies View Related

Setup 3Com Wireless Access Point?

Sep 4, 2012

I am trying to set up my 3Com wireless Access Point that was given to me. I have searched for software to set it up but can't find any.I have read somehwre that the software doesn't even work on Windows 7 anyway.know the default ip adress of this router or how to get into the config pages to set it up.

View 19 Replies View Related

Multiple Wireless Access Point Setup?

Feb 13, 2011

I need to setup my laptop for two different wireless configurations,at home i have a wireless network that work fine, however, at work i need to configure TCP/IPv4 by feeding in the required IP, Subnet Mask, Gateway etc. But i have to repeat this everyday in office and at home by removing and feeding in the parameters. Is there anyway that i can have both configurations and the system just automatically finds the right wireless network without changing the parameters. I am using windows 7.

View 4 Replies View Related

Modem Router Access Point Setup?

May 15, 2012

I bought the DIR 655 to put into our network as the Netopia wireless fails to connect even though we have maximum signal strength. Att advised that buying a third party router would solve this problem.I did manage to almost configure the DIR 655. I would have to connect it to the system to test it[CODE]

View 5 Replies View Related

Setup Buffalo WHR-HP-G54 As Wireless Access Point?

Nov 28, 2012

Setup Buffalo WHR-HP-G54 as wireless access point?

View 1 Replies View Related

Linksys Access Point :: How To Setup AP To WRT310N

Aug 31, 2009

I have an EnGenius AP (EOC-2610) I want to connect to my primary router (WRT310N) to extend my network. how I must setup the WRT310N (and maybe the EnGenius) to make it all work together ?
 
Is the AP's IP should be static ? ie 192.168.1.2 (next to main router's IP)or should it be static in the the primary's DHCP range ? ie 192.168.1.101 or should it be dynamic the IP given by the primary router ?

View 3 Replies View Related

Wireless Access Point Setup For Apartment Complex?

Apr 25, 2011

We are looking into setting up wireless internet access for the whole complex.

1) We would have around 200 users at max (accounting for people to have more than one device or computer connected. Such as Xbox360 and whatnot). What speeds should we consider from a ISP.?

2) Should we get more than one ISP feed?

3) How many wireless access points should we get? (Ruffly we are looking at 5-6)

4) Where should the WAP's be placed around the complex? Considering the apartments are brick outside and inside regular wood frame/drywall construction type. Also should they be inside or outdoor WAP's.

5)What hardware should be considered? (switches, WAP's, ect...)

View 2 Replies View Related

Netgear Router Setup - Access Point / Switch?

Dec 9, 2011

I need to setup my Netgear as a switch/access point. I need the following set-up. My ipconfig /all reports:

View 27 Replies View Related

How To Setup Linksys Wireless Router As Access Point

Aug 14, 2011

Can I use a second linksys wireless router as an access point and can I connect a wired computer to one of its ports?

View 1 Replies View Related

Linksys Access Point :: WES610N Cannot Get Into Web-based Setup

Aug 9, 2012

The WES610N bridge seems to work fine, but I cannot get into the web-based setup.  I have tried using it directly through my laptop, as the instructions show, then through an Asus RT-53N as a router. I did have the 610 connected to my laptop's ethernet socket, where it provided internet through the Asus RT-53N wireless router just fine, but when I tried to access the setup, again, it would not work. Next, I tried it through a desktop and Linksys RVS4000, again nothing. I would like to check the firmware and see what else is in the menu.

View 6 Replies View Related

D-Link DIR-615 :: Setup Free Access Point But To Internet Only?

May 24, 2012

I have configured my DIR-605L for no security. I want to provide free wireless internet for the guests that come to my house. How do I insure that guests connecting wirelessly to the 605 can access the internet only and can NOT hack into the computers on my internal house network?

[code]....

View 3 Replies View Related

Cisco Wireless :: Setup RV220W As Access Point?

Nov 10, 2011

May I know that can a CISCO RV220W setup as a Access Point in company network? We already have a router for IP management. is it possible to setup as Acces point?
 
Also can we separate the guest and internal user for using wireless by difference SSID and VLAN. It seem it cannot setup if i need to setup limited network access right by SSID and VLAN.

View 3 Replies View Related

Belkin Routers :: 5FD8235-4 V2 - Access Point Setup

Feb 2, 2013

If I want to setup my N+ router 5FD8235-4 V 2 as an access point. How do I go about doing that?

View 5 Replies View Related

Cisco :: Wireless Access Point AP541N-E-K9 Setup

Oct 2, 2012

I have installed the following wireless access point on our network:
 
-Product Identifier: AP541N-E-K9 
-Hardware Version: V01 
-Software Version: AP541N-K9-2.0(0)
 
I have created 2 VAP's and give each one an SSID. They both have the same VLAN ID. I have setup as follows:
 
1) The first VAP I would like to give internet access and access to our internal network shares.
 
2) The second VAP I only wish to give internet access and no access at all to our internal network (for guest access). I am also using HTTP redirect with this.
 
how can I achieve the setup in number (2)? This is to give internet access, but not share the internal network.

View 2 Replies View Related

Linksys WRT54G Setup As Access Point On Wireless Network?

Jun 28, 2011

I have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.

View 2 Replies View Related

Linksys Access Point :: How To Setup WRT54G In Router Mode

Jan 20, 2007

How to setup WRT54G in router mode

View 9 Replies View Related

Linksys Access Point :: How To Setup Wap54g As Repeater To WRT54GL

Jun 25, 2011

I have WRT54GL and want to setup wap54g as wireless repeater? I need to expand the signal using wap54g

View 1 Replies View Related

Linksys Access Point :: Wap54g Setup Wizard 3.0 Download?

Jan 13, 2012

wap54g setup wizard 3.0 download

View 1 Replies View Related

Linksys Wireless Router :: How To Setup E1500 As An Access Point

Oct 23, 2012

How do i setup my Linksys E1500 router as an access point? I have a main router upstairs but the signal is weak in the basement. How do i configure this router as an access point for internet?

View 2 Replies View Related

Linksys Access Point :: WAP610N - Setup Not Finding Device

Jul 2, 2011

I've got a WAP610N access point and 4 WET610N to connect to it - however, no matter what I do when trying to install the WAP610N the setup tells me it cannot find the device.I've got the WAP610N connected to a homegateway (SAGEM) and my computer connected wired to the HGW. The HGW is setup as a DHCP server, everything beside the WAP610N works. It gets an IP address, and I can login to the web interface of the access point - but is still unable to use the setup and unable to connect any of the WET610N.

View 2 Replies View Related

Setup Netgear WNR2000v2 Router As Wireless Access Point?

Jan 6, 2012

How do I setup Netgear WNR2000v2 wireless router as a wireless access point? I just upgraded to a Netgear WNDR3700 wireless router and I don't wanted the wnr2000 to go waste. So basically as the followings:

Internet(modem)---Ethernet cable--->3700---wireless-->2000---Ethernet cable-->Xbox360/PS3.

View 8 Replies View Related

Setup 3600HGV As Modem Only / Have Netgear DGN3500 As Wireless Access Point

Apr 19, 2011

I'm trying to find out if it's possible to setup a 3600HGV (VDSL Gateway) as modem only and have a Netgear DGN3500 (ADSL2+) as a wireless access point. I'm aware that both are DSL modems, my reasoning for wanting to have them both hooked up is that

a) the 3600HGV has no Gigabit switch and runs on wireless G

b) the DGN 3500 has a Gigabit switch and does wireless N. So in a nutshell I want the 3600 as simple modem and the 3500 as a wireless N access point with Gigabit switch.

View 4 Replies View Related

Linksys Cable / DSL :: WAG54G How To Setup Access Point And Make It Work With DSL

Mar 15, 2009

i'm facing a big problem with my access point WAG54G ver 2.0 ,i just bought it from 2 days but i find alot of problems when i start using it ,i have read all the user guide and the quick install to see how to setup the access point and make it work with my adsl.i have configured all things right using PPPOE and putting my user name and password and then save settings then go to the status and press on connect , but it don't connect with me just i find connecting and adsl link : Down and still making connecting  and nothing after that and my adsl led is off haven't any colors ,and when i get again to basic setup i found the password that i put it in the ppoe login is too long , not my password i tried to see what is this password and recover the hidden i found it " d6nw5vlx2pc7st9m ".i don't know what is the problem i tried alot of times to change setting and also the same problem.i think that it's a frim ware problem and i tried install a new updated frimware but everytime trying to install it get installing and suddenly stoped and white page appeard and all the access point is stopping and when restart it the ac power.

View 3 Replies View Related

Cisco Wireless :: WAP4400N / How To Setup Access Point To Sync With New Router

Feb 16, 2012

I had been using a Linksys Wireless-N Router WRT350N with a Linksys Wireless-N Access Point WAP4400N.  The router quit working so I upgraded to a Linksys Wireless-N Router E1550.  The problem is, the new router doesn't sync with the old access point. how to setup the Access Point to sync with the new router?

View 1 Replies View Related

Linksys Wireless Router :: Setup Wrt54g As Access Point To Extend Signal?

Aug 17, 2011

how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
 
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?

View 1 Replies View Related

Cisco Wireless :: Setup 2504 WLAN Controller And 1142N Access Point?

Jun 13, 2013

We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?

View 1 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Cisco Wireless :: Point To Point Access Point 1262 Bridging

Feb 27, 2013

How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.

View 12 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved