Split A Single Pair Of Straight Cable To Get Two

Dec 28, 2012

I have one running UTP cable of around 50m, terminated at a point. Is it possible to split my cable so that i can terminate two points - so that i can connect my 2 Pc without a switch in.

ADVERTISEMENT

Split A Single 4 - Pair Ethernet Connection Into Two 2 - Pair Ethernet Connections

Dec 28, 2011

I've got a router on which I run a backup/media/print server, a couple of computers and a voip box. My router has only four ethernet lan sockets which are thus all occupied by the above, but I need to attach at least one further device b

Secondly, could a splitter such as >> this one << do the job? I'm guessing this basically split a single 4-pair ethernet connection into two 2-pair ethernet connections.

View 2 Replies View Related

Creating A Network Cable (crossover Or Straight Through)

Oct 28, 2012

I just got done running CAT 6 wire's into different rooms and placing jacks on the wall which all works correcting going into the patch panel. The problem I am having is that the Access Points on the ceiling I decided to make it a little easier and use regular network cable and cut one end off and place it into the patch panel the same way as all the jacks. The AP's are POE and they are just not getting on the network. Do I need to do something different for this cable?The way I punched all the wall jacks and all the cables to the patch panel is by using section B on the jack so because of me cutting a cable and leaving one end on, should I use A or is there something else I should do?

View 3 Replies View Related

Transfer Speed Between 2 Gigabit Lan PC Through Straight Cable?

May 21, 2011

I have a desktop and a laptop computer. both equipped with Gigabit Lan port... I connect them with Straight cable by assigning both computers IP address. I havnt use any switch or router between computers.... The problem is that my transfer speed is about= ~10MB/s..... As far i know the transfer speed should be around 70-80MB/s (125MB/s for Gigabit Lan).....

View 5 Replies View Related

Routers / Switches :: Difference Between Cat5e And Straight Cable?

Jun 17, 2011

what is the difference between cat5e and straight cable?

View 3 Replies View Related

Cisco WAN :: Split Data Flows Over A Single T1

Nov 7, 2012

Is it possible to split data flows on a single T1.  Say 1 Flow on time-slots 5-6 and another data flow on time-slots 10-14.  If one was data and the other voice would this work?

View 6 Replies View Related

Cabling / Cards :: Convert A Cat 5e Crossover Cable To Make It A Straight?

Feb 9, 2012

easiest way to convert a cat 5e crossover cable to make it a straight? I have 2 PCs networked & am introducing a router & need to covert the cable without having to rewire it if possible.

View 1 Replies View Related

LAN Over Copper Twisted Pair Cable

Jan 14, 2013

Is it possible to run a large LAN over copper twisted pair cables?This is to connect 41 PC's that monitor fire systems on a large hospital site.I am trying to use the existing cable that is wired in a loop all round the site.

View 2 Replies View Related

Wiring A 2 Pair Cat 5 Cable To A RJ-45 Connector?

Oct 31, 2012

I have a long 2 pair cat 5 cable which I want to use to connect a ADSL modem to my desktop (located in a different room). I took the cable to few local computer dealers but none of them could connect an RJ-45 connector to it. They can only connect a 4 pair cat 5 cable. Connect a 2 pair cat 5 Ethernet cable to a RJ-45 connector. Kindly use simple language. I have attached an image of the cable for your reference. [URL]

View 5 Replies View Related

Can Split Cable To Create Own Network

Nov 4, 2012

My question is can I split my cable to create my own network? For example my direct cable wire into the home then split it to tv then router to my laptop...

View 1 Replies View Related

Split Ethernet Cable One To Computer Other To Wifi Router

Dec 13, 2011

I have only one computer right now.Had two, and got very weak signal to laptop (since discarded) upstairs from Linksys g 54Mbits downstairs at main desktop computer desktop.I have tried three different kinds of 54Mbits wifi routers, all with no success.I'm going to get my wife a new wifi laptop for Christmas, and she wants to be able to use it all over the house.The 54Mbits will cover the downstairs, but, based on previous efforts, I am thinking of putting my modem in the garage, where the cable enters my house, and using a splitter on the cable coming out of the modem to make two IN cables, using one cable for my comp and a 54Mbits router (for downstairs coverage), and putting a second wifi router on the end of the upstairs cable, to cover the upstairs rooms.My house has cable outlets in every room, so I won't have to do any wiring.

I plan to leave the routers on all the time (at this time) subject to how much of a bandwidth drop they cause. I have a 100 Mbps connection, and I play games, so I'd like to retain as much bandwidth as possible. I assume the two "on" wifi routers will pull zero bandwidth as long as the laptop is off. (??)Or maybe I should just try an "n" wifi router, since they get twice the distance, and forget the cable splitter idea.

View 7 Replies View Related

Can Split Internet Cable To Connect A Digital Phone

Sep 26, 2011

can i use a cable splitter to connect my digital phone and my router? Currently my digital phone box is connected to the cable modem and my router is connected to the digital phone box. However I noticed that the internet speed is negatively affected.

View 3 Replies View Related

Linksys Cable / DSL :: X2000 Split Internet Bandwidth

Oct 29, 2012

I have linksys X2000 modem and linksys WAG 200G modem I can use them both if needed I want to share my internet with my brother on our house But I want each one of us to have equal bandwidth ( speed ) How can I do this using those devices.

View 4 Replies View Related

Cisco Switching/Routing :: Pair Of N7K Distribution Switches Connected To A Pair Of Aggregation Switches

Mar 11, 2012

We have a pair of N7K distribution switches connected to a pair of N7K Aggregation switches.We run vPC on both pairs of n7k's.

-n7k-d1 has two interfaces in a Port-Channel connecting to n7k-a1 & n7k-a2. (PC1)
-n7k-d2 also has two interfaces in a Port-Channel connecting to n7k-a1 & n7k-a2. (PC2)
 
My problem is that Spanning-Tree is blocking PC2 and all traffic from n7k-d2 is traversing the Peer-Link before reaching the Aggregation layer. Is this the best design for connecting two pairs of n7k's with vPC or if a better design would be to connect all 4 links into the same Port-Channel and vPC?

View 7 Replies View Related

Cisco VPN :: ASA 5520 / Error / Split Tunnel Attributes(51) Greater Than Max Allowed Split Attributes(50)

Jul 21, 2012

We have ASA 5520 acting as the VPN Server and Cisco 1941 router as EZVPN client. Since last few days client is not able to establish vpn connection. 1941 router is continuously generating the below log messages
 
001569: Jul 22 12:19:05.883 ABC: %CRYPTO-4-EZVPN_SA_LIMIT: EZVPN(VPNGROUP) Split tunnel attributes(51) greater than max allowed split attributes(50)
 001574: Jul 22 12:19:07.835 ABC: %CRYPTO-6-EZVPN_CONNECTION_DOWN: (Client)  User=vpn_user  Group=VPNGROUP Client_public_addr=<client public ip>  Server_public_addr=<server public ip>
 004943: Jul 22 11:32:42.247 ABC: %IP_VFR-4-FRAG_TABLE_OVERFLOW: Dialer1: the fragment table has reached its maximum threshold 16

View 3 Replies View Related

Sending Two LANs Over A Single Ethernet Cable?

Dec 24, 2012

My VDSL subscription will include both Internet, and TV. The supplied router then makes them available via two separate ports with different address ranges. LAN cables then connect to the computers and TV decoder from these ports.In the house there is a single Ethernet cable already running through the walls from the basement to the lounge on the ground floor. I want to consolidate both the Internet and TV data onto this cable and then split it apart again at the other side to go to a TV decoder and a wifi router.I don't want the VDSL router to be in the lounge as I will also have a TV decoder and Internet connection in the basement.I am renting the property so I can't run new cables through the walls etc.

View 2 Replies View Related

Cisco Switching/Routing :: 3750 - Two Switches Connected With Single Mode Cable

Jun 4, 2012

I am troubleshooting a fiber connectivity issue.Now I have two switches, one is 3750, and another is small biz 300 series switch. Both switch has a single mode smf gbic. Now I have two swtiches face to face and connect with a single mode cable. Do you think if I would get a link light on? Both ports are no shutdown.

View 3 Replies View Related

Two MDI-X Devices Using Only Straight Through Cables?

Aug 31, 2011

I purchased a D-Link switch that supports MDI-X so I should be able to use only straight through cables according to the manual. My Router (Wrt54gs) also supports MDI-X, yet when I plug a straight through cable from port 4 on router to port 1 on the switch -> then a straight through from port 2 on the switch to my computer, I don't get an IP address.If I connect a crossover cable from the router to port 1 on D link switch -> then straight through from port 2 to computer, it works just fine.I am going to purchase an extra crossover cable to use for this but I'm really curious as to why it wont work this way? DES-1105 is the model of the switch. "THE DES-1105 CAN BE CONNECTED TO ANOTHER SWITCH OR OTHER DEVICES (ROUTERS BRIDGES ETC) VIA A TWO-PAIR CATEGORY 3,4,5 UTP/STP STRAIGHT THROUGH OR CROSSOVER CABLE."

View 2 Replies View Related

Cisco :: VRF Aware Peering With Straight BGP?

Mar 24, 2013

I have a scenario where I may have to run VRFs on a router that is currently facing an ISP as a BGP peer. peering two BGP peers, one of which is VRF aware (and hence configured within the address-family ipv4 vrf X subsection) and the other is not? (the BGP aware and internet facing segment will go into its own VRF where previously this router was only in that VRF and hence had no awareness).Are there any caveats or restrictions? Does the presence of the VRF throw the ISP peer?

View 3 Replies View Related

Cisco Switching/Routing :: 6500 MTP / MPO Crossover Cables Or Straight Through?

Jan 20, 2013

I'm looking to deploy a pair of 6500s running VSS. VSS will be established over a pair of 40GBASE-SR4 QSFP+ transceivers in each switch.Do we need MTP/MPO crossover cables or straight through cables to connect the QSFPs?Since the two switches are sitting side by side the MTP/MPO cables will be passed directly between the two racks.As a result there will be no intervening fibre fobots used.

View 1 Replies View Related

Home Network :: UTP Cables Are Crossover Cables Or Straight Through?

Jul 17, 2012

UTP cables are crossover cables or straight through??

View 5 Replies View Related

Cannot Pair Android Phone And Laptop

Feb 7, 2013

For some weeks I have been trying to pair my Samsung Galaxy S2 with my Lenovo Thankpad SL500. The consistent message is "Unable to pair with [laptop]. Incorrect PIN or PASSWORD.

Well which is? PIN? or PASSWORD? - or does the system not know, so it's taking a guess? If it doesn't know, how can I possibly know?

Having read many articles about his on the www, I am still none the wiser as to what is causing this. What's wrong with the PIN or PASSWORD - is it too hot, or too cold? Wrong font face, colour or size? Wrong latitiude, longitude or elevation? Wrong time of day or month? Are the auspices in general not favourable? Am I facing in the wrong direction as I type? Have I chosen the wrong weight/color of paper for my printer? Is my body odor unacceptable? Is the length of grass in my lawn not quite right? Oh, the number of options is so large - where does one start?

Oh, and before I forget - assuming I can find what constitutes a correct PIN or PASSWORD, where does one set it? btw pairing this phone with the media player in my 10 year old car works immediately and flawlessly!

View 10 Replies View Related

Cisco :: ACS 5.4 Distributed Pair Installation

Apr 20, 2013

We would like to install a pair of ACS 5.4 apliance as primary /backup  in our two datacentres.I have some question regarding degin.
 
1- We have 800+ network device to monitor , can we install by range of address instead of instlling one by one in device host database ?
2- Do We have to install all 800 device first on Primary and then again on backup or Primary will replicate to backup server?
3- We do not have real IP address yet, so if we built with dummy address and make them pair and all the database sync, then when we change their IP address, will the distributed primary pair will have any issue with backup ACS server?

View 7 Replies View Related

Split Network Into 3 Subnets?

Oct 9, 2012

I need to split a network: 10.0.4.0/24 into 3 subnets with the following hosts per subnet:

Subnet 1: 80 hosts
Subnet 2: 10 hosts
Subnet 3: 120 hosts

split into 3 subnets?

Im thinking something like this:

Subnet 1
Network 10.0.4.0
Subnet Mask 255.255.255.128

[Code].....

View 1 Replies View Related

Way To Split An Ethernet Connection

Jun 29, 2011

I need to split a connection so I can get internet to two computers.

View 11 Replies View Related

How To Split Home Internet

Nov 5, 2011

I got cable modem broadband and need to share that Internet amongst my home, my home office and the apartment I rent out to a tenant on the second floor. I also need them to be on separate networks/LANs/zones so they can't see each other (but still sharing the same Internet connection). How do I do this?

View 3 Replies View Related

Split Network Without VLAN?

May 1, 2012

I need to split a client's current LAN into 2 LANs so that the staff's office computers and devices are not accessible to the residents/guests. They currently have a modem+router device that gets it's public IP via DHCP, a couple of switches and a wireless access point that both staff and residents connect to (same SSID). The catch is they don't have static public IPs and the modem+router device MUST keep the current LAN IP network schema (10.1.10.0/24) or the ISP won't provide technical support.

View 6 Replies View Related

Use A Switch To Split My Internet?

Dec 31, 2012

Im about to move into a sleepout which is about 20 metres away from the router. I was thinking of laying a network cable out to my room which would connect to a switch then use network cables to connect up my PS3, TV and Computer. Is this all going to work?

View 1 Replies View Related

Home Network :: What Is A Twisted Pair Transceiver

Nov 5, 2011

I purchased a couple of used Cisco Routers and Switches and the guy gave me a bag with some cabling and one of these little guys were inside:

I have seen them plugged in before on images of peoples labs, but what are they used for? Why would I want to use this?

View 3 Replies View Related

Cisco Wireless :: 5508 HA Pair Licenses

Apr 17, 2013

I have 2 5508 that are currently running as active with 150 licenses each. I want to go to HA SSO can 100 of the licenses be relicensed to the primary since it only requires 50 licenses to convert an active license 5508 to standby HA SSO?

View 3 Replies View Related

Cisco Firewall :: ASA 5520 - Failover Pair

Oct 31, 2012

i am trying to setup a failover pair on Cisco asa 5520 - need a state full failover. Do i need two ports dedicated to obtain the above - one for LAN based failover and one for state full fail over ? also do i need a switch in between to connect them ?

View 11 Replies View Related

Split An Ethernet Connection To 2 Computers?

Oct 27, 2011

We inherited a soundbooth configuration Current Configuration:

1. Networked Projector interfaces directly with a PC through a second NIC

2. We can then control the projector through a web interface via the PC and the IP of the projector.

Desired New Configuration:

1. Maintain current configuration - but ADD a second computer (an iMac)

2. I want to split the connection coming from the projector to the 2 computers so that we can interface with the projector from both computers.

I was thinking I would need a switch but didn't know if there is any configuring I would need to do to get it to work.

View 3 Replies View Related

Cisco :: Split Tunneling / ACL On ASA5510

Jul 16, 2011

I just moved our vpn over to using LDAP/DAP instead of the previous RADIUS we were using before. First of all, the group policy split tunnel is setup for Tunnel Network list Below Network list has a group of networks named "split-tunnel" setup with all of our internal subnets in it. Which seems to be working fine, users are hitting internal networks no problem.Where the issue lies is surfing the web while they are connected to the VPN.I think I know what one of the the issues are, I'm just not sure how to get around it. I have a proxy server setup that all domain traffic goes through say 10.20.30.40. That is obviously on our internal subnet. Our remote users has a policy on their laptops set to where if they can see/get to the proxy server then it pushes all traffic through there, however if they can not, it goes straight to the internet. That way they can still surf the web when they aren't connected to the domain network.

With the new DAP vpn policies, it seems as though they are trying to go through the proxy but failing so all http traffic is getting blocked on their computer as I can still ping say google.com...just can't open the web page.In my SALES-VPN access lists there isn't any acl that allows any traffic to 10.20.30.40(proxy server) so there isn't any reason their laptop would think it could get to it correct?I can't put an access-list SALES-VPN extended deny ip any any log critical at the end of the acl list because then it doesn't show up as an option to apply to the DAP since the acls have to be either permit or deny, not a mix.Also, if I just create an ACL access-list DENY-VPN extended deny ip any any log critical and apply it to the DAP *after* the SALES-VPN ACLs thinking all traffic would flow down as in go through all the permit acls first, and then hit the deny acl after, it just blocks all traffic.It almost seems that some traffic that isn't specifically being permitted by the permit acls is still getting through which is obviously not wanted. However, if I try to rdp into a server that isn't specifically permitted in the SALES-VPN acls it doesn't work so I'm kind of at a loss..

View 5 Replies View Related

Cisco WAN :: 891 - Split Internet Bandwidth

Aug 22, 2012

I'm pretty new to this, and I've been trying to read up on what I should do. Here's my situation: we have a new 15mps internet connection coming into our building. We also have a new 891 router. We would like to devote 1.5mbs at the highest priority to one LAN which is just used for VOIP phones. We would like to allow one of the other tenants to use up (but no more than) to 5mps for their LAN, and we'd like to be able to use up to 13.5mps for ourselves if it's available, or at least 8.5mps (15-1.5-5=8.5).

From searching in here and reading the various articles on policing and shaping, I'm thinking that we'd want to set up Class-based weighted fair queuing on a per-interface basis, and have one interface connected to our VOIP switch, one connected to the other tenants switch, and one connected to our firewall. Does this sound like the right way to go? And would anyone have an example of a configuration which achieves this?

View 15 Replies View Related

Cisco VPN :: How To Enable Split Tunnel On PIX 501

Nov 17, 2012

I have several PIX 501's and one of them is extremely slow accessing network resources and does not have Internet access. I would like to use split tunnel and have them access the Internet throught their DSL connection and any traffic for network resources sent over the VPN. How can I improve the speed and set up split tunnel via the command line?  I dont have the PDM software so I guess I will need to do all the configuration via the command line. Below is the configuration:
 
PIX Version 6.3(1)interface ethernet0 autointerface ethernet1 100fullnameif ethernet0 outside security0nameif ethernet1 inside security100enable password k4HlcGX2lC1ypFOm encryptedpasswd y5Nu/Nt1/5dK8Iuf encryptedhostname

[Code].....

View 1 Replies View Related

Cisco WAN :: 2911 Split Traffic From LAN

Jun 11, 2013

I have a Cisco 2911 Router and I need to split the traffic from my Lan (Gi0 / 0) by ISP1 (fa0 / 0) and that of my servers (Gi/0/0) by ISP2 (fa0 / 1). [code]My problem comes when wanting to communicate with my remote networks that reach the int Gi 0/1, because when my network to match the policy- route internet sends me all the way.

View 1 Replies View Related

Cisco VPN :: ASA 5505 Split DNS Setup

Mar 2, 2011

I have an ASA 5505 configured using easy VPN connecting to our corporate ASA.  The ASA5505 is configured for network extension mode with a routable subnet.  The clients that hang off the ASA 5505 are DHCP and get their IP address and DNS settings from the ASA 5505.  I have a split tunnel setup, so only certain networks go over the tunnel back to corporate.  Local Internet browsing goes out the ASA 5505 to the ISP.
 
My questions is how to setup split-dns.  i would like to have my clients query the ISP's DNS servers for Internet based websites and when they need to access the exchange server the query goes to our corporate DNS servers.  I see a setting for DNS names under the group policy on the corporate ASA, but how does the client know which DNS server to use?
 
The clients receive a primary DNS server (ISP) and a secondary (Corporate DNS) from the ASA5505.

View 5 Replies View Related

Cisco :: Citrix NetScalar Vs Anyconnect On A Pair Of 5540s

Oct 30, 2011

My colleague wants to use our load balancers for VPN. We are coming off 3030s which are serving remote access IPSec as well as terminating LAN to LAN tunnels for like 7 sites.I want to secure the 5540s behind our front end 5585Xs when we move prod to the new dc.We have no immediate need for clientless but need to support osx lion and IPSec client does not. Thats all that's driving this effort currently. I already reminded mgmt that the 3030 and the IPSec client are end of life.I just think anyconnect is the better solution based on current skillset and the popularity of the solution.

View 2 Replies View Related

Cabling / Cards :: Home Network Wiring With Pair 1-2

Jun 10, 2012

I am converting my home phone jacks to network enabled jacks. The house phone system was wired with Cat 5e. All the wall jacks are terminated properly with RJ-45 connectors. At the junction box outside I have connected the 4 pairs to their color equivalent.I have also purchased a "patch board" to terminate and combine all the wiring in one spot.Once all the wires are connected, I tested the wiring (Sperry cable tester).It tells me there is a short in 1-2. I've made it this far and I'm really close, I just need to know which pair I need to focus on. Is pair 1-2 Orange/OrangeWhite, Green/GreenWhite, etc?

View 1 Replies View Related

Cisco Firewall :: 5520 - ASA Failover Pair With Different License

Apr 15, 2013

I have a running ASA5520 in my network and recently we plan to add a failover pair as a standby unit for the running asa. Both of the ASA have the same specs and software. the only thing that the soon to be secondary ASA does not have is the AnyConnect Essential license. is it still possible for the unit to be the standby unit?
 
below is the license capture from both of the unit.
 
Running ASA:
Licensed features for this platform:
Maximum Physical Interfaces  : Unlimited
Maximum VLANs                : 150     

[Code].....

View 3 Replies View Related

Cisco Switching/Routing :: Extending LAN Using 888-k9 Over One Twisted Pair

May 3, 2012

I already know that there is an option using Patton Copper Link Ethernet extender to interconnect a remote LAN with this device. Do you know if this is possible using Cisco 888-K9 or any other Cisco Device ?

View 2 Replies View Related

Cisco Firewall :: Activation Key For ASA 5520 Failover Pair

Mar 20, 2012

We have recently got 2 of our Cisco ASA 5520 firewalls through RMA. These are supposed to run in a Active/Active Failover Pair. There was only 1 RMA request that was opened for both the firewalls. We have received only 1 Activation key for this RMA request for both the firewalls. Just want to check with you if this Activation key will work on both firewalls or do we need a get a seperate one for the other box.

View 1 Replies View Related

Cisco VPN :: Set Up Remote Access IPsec VPN On Pair Of ASA 5540

Feb 6, 2011

I'm trying to set up remote access IPsec VPN on a pair of ASA 5540 without much success. I can connect with a client on the outside, and when I try to ping something on the inside I can see the ping requests reach the target but the answers don't come back to the VPN client. I've tried with different NAT rules without success.

View 3 Replies View Related

ADVERTISEMENT