Static IP For Port Forwarding?

May 25, 2012

I need to set a static IP for port forwarding so my clients can connect directly to my server. I kept losing people because my IP address would change every week. I use version MI424WR router and know my Mac address but do not know which IP address I should set it to.

View 6 Replies


ADVERTISEMENT

CCTV Static IP And Port Forwarding

Jun 7, 2011

I recently purchased a CCTV System and linked it to my LAN.I use a Netgear DGN2200 Router and link from the CCTV DVR using Ethernet over the Socket Ring, (again using a Netgear product).I want to access the DVR over the internet and seem to have used internet based advice and got confused. Do I have to contact my ISP and pay for a Static IP? I am on BT Business Broadband and they say I need to pay 5pm to have a Static IP, but Port forward.com indicated that this is not necessary to set up a Static IP, and "watch your ISP doesn't try and sell you one." url...I am not clear on whether the Router needs to be linked statically to the ISP or does my PC???

View 14 Replies View Related

Cisco Switching/Routing :: 877 - NAT And Port Forwarding With 6 Static IP?

Aug 23, 2011

I've 8 Static IP assigned me from my ISP.

x.y.w.56 (not usable)x.y.w.57x.y.w.58x.y.w.59x.y.w.60x.y.w.61x.y.w.62x.y.w.63 (no usable)Subnet 255.255.255.248
  
I've a 877 Router and I would to:NAT al LAN Client with x.y.w.57Configure some ports ( i.e. 80 and 443) to be forewarded from x.y.w.57 to one LAN Server ( i.e. 192.168.0.1)Configure some ports ( i.e. 443) to be forewarded from x.y.w.58 to another LAN Server ( i.e. 192.168.0.2) 

View 3 Replies View Related

Cisco Routers :: RV220W - Firmware 1.0.3.5 Port Forwarding With Static IPs

Apr 24, 2012

I have read every post here about port forwarding on the RV220W and none are clear. Here is my scenario.
 
I have 5 static IP Addresses. I want to use one of the IP addresses to setup remote access using Remote Desktop Connection from outside the office using port address translation. for example i would like to use RDC and a specific port such as 7000 and connect to an internal PC on port 3389. sounds simple. i do this all the time on Cisco ASA's, Netgear, D-link, etc. but for the life of me cannot do it on this cisco firewall. so the port address should look like 25.25.25.25:7000 and connect to 192.168.1.25:3389. i have tried everything based on the posts without luck.

View 1 Replies View Related

Linksys Wireless Router :: Port Forwarding Using WRT160Nv3 To Minimize Static?

Nov 27, 2011

I have been using this router for quite some time, with a setup like.. Cable Modem ==> Vonage ==> WRT160Nv3 ==> PC.  It has been working very fine for all these years (6), but now I hear static disturbances in my phone calls, and so I decided to do port forwarding for the vonage device, to minimize the noise.  This device uses a static ip address of 192.168.15.1, and in the Linksys software, I am not able to use any ip addresses other than "192.168.1.*" in the port forwarding page.  

View 1 Replies View Related

Linksys Wireless Router :: E2000 / Setting Static IP For Port Forwarding?

Jan 2, 2012

I currently have cable internet connected to one router (Linksys E2000 w/ firmware v1.0.03). That router is connected to another router, a Linksys E3200 w/ firmware v1.0.02. In order to properly forward ports through the E3200, I understand that I need to set up a static IP on that router.I've basically followed the steps outlined in this video, but when I enter all the IP addresses for Static IP settings, it won't allow me to access the router's setup page. I try entering the new IP that I've given it (which it tries to direct itself to automatically after I save the settings) and the connection times out. I am able to access the internet otherwise, however. From here I'm forced to do a factory reset on the router and start from square one.

View 6 Replies View Related

Cisco Switching/Routing :: 881W - IOS Port Forwarding Commands For Port Forwarding

Apr 7, 2013

I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.

View 1 Replies View Related

Cisco Routers :: RV042G - Port Forwarding To 2 Different Destinations Based On Incoming Wan Port

Apr 22, 2013

how to: port forwarding to 2 different destinations based on incoming WAN port
 
The default HTTP service works fine: TCP80/80-> 192.168.0.55
 
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
 
I was able to do port redirect with the Symantec Firewall I'm replacing.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-8970 Port Forwarding To A Different Internal Port

Mar 7, 2013

Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media

Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.

View 1 Replies View Related

Cisco Firewall :: Change Default SSH Port On ASA 5505 (port Forwarding)

Dec 2, 2011

So here is my network.
 
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
 
and here is my dilemma.
 
I can SSH from the internet to my ASA on default port 22, directly to my public IP.  I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960.  From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841.  I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
 
The bottom line is that i want to be able to SSH to all three devices from the internet.  I only have one public IP.  As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001.  It appears that changing the default SSH port on Cat 2960 is not an option.  It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
 
show asp table socket
TCP       001f549f  <<pub IP>>:22              0.0.0.0:*               LISTEN
 
how do i make it listen on different port?
 
Here is relevent config for SSH for cisco 1841 (port forwarding)
 
ON ASA
object network ROUTER
host 10.10.1.1

[Code].....

View 28 Replies View Related

Cisco Routers :: RV042G Port Forwarding From Public Port To Internal IP?

Oct 11, 2012

Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
 
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80

View 2 Replies View Related

D-Link DIR-655 :: Subsonic Port Forwarding / Get Machine - Port From Outside / Internet

Feb 16, 2011

I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server.  Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening.  However, I can't seem to get to the machine-port from outside/internet. 

I have tried Virtual Server and Port Forwarding with single port.  The server has a stactic IP which I've included in the DHCP range and outside the range.  I have a DSL connection (AT&T), modem only.  I have updated firmware.  I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct.  What am I missing?  Is if possible there is a defect in the router? (don't laugh).  Is there a way to trace a request to that port to see where it is hanging?

(yes, I've STFA, but don't know what else to do).

View 2 Replies View Related

Cisco :: Not Enough Port Fields In Port Forwarding For Linksys E4200

Jul 16, 2011

I have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
 
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking ****, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
 
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.

View 1 Replies View Related

Cisco Routers :: SRP541W Set Up Port Forwarding From External Port

Apr 13, 2013

I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.

View 6 Replies View Related

Cisco WAN :: 7960 - Static NAT Public-Private Forwarding On 887VA

Sep 3, 2012

So, I have a bit of a problem getting out Natted Cisco 7960 working with our external SIP providers behind NAT.
 
We have a block of IPs available to us, however when I asign a static NAT rule for the internal phone, outgoing calls are fine but incoming provides no audio.
 
We have no ACL blocking or anything, it's fully open to the outside world with the IP assigned to it via NAT.
 
Our static NAT rule for the phone:
 
ip nat inside source static 192.168.0.250 xxx.xxx.xxx.xxx
 
NAT is configured on the phone, with the external IP set correctly.
 
Also, after a while, it seems as the the registration times out or something because incoming calls no longer work.
 
I thought a static NAT rule would just allow full access to incoming connections to the internal IP specified? Our main router config (with unnecessary information removed):
 
version 15.1
no service pad
service timestamps debug datetime msec

[Code].....

View 4 Replies View Related

Cisco Firewall :: 5505 Static Nat With Port Redirection 8.3 Access List Using Un-Nat Port

Aug 15, 2012

I am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.

View 12 Replies View Related

Home Network :: Port Forwarding Not Access Port

Jul 31, 2011

I want to create a Counter Strike Server and need to open some ports for that.The Problem: I cannot seem to open the ports for gaming.The Modem Setup: My Firewall is disabled.My guess is that, this is the area with the problem. I guess my modem is not forwarding onwards.The Problem: I tried checking my ports with websites like URL etc.It cannot access my port.

View 1 Replies View Related

Port Forwarding Port 80 Blocks Internet For Everyone Else?

Aug 7, 2011

I have a DSL-524B from D-Link. My problem is, whenever I Port Forward port 80 to my comp's IP to host a web server, all the other computers connected to the router are unable to access the Internet. So, I set up no-ip to use port 8080, but, this exposes my ip and even when masking, if you look at the HTML code, you get the ip.I need to know how to open up port 80 without restricting Internet access to only my comp, or any other work around.

View 7 Replies View Related

DI-524 / Port Forwarding With ATT DSL?

Nov 10, 2012

I was at a friend's office today trying to get the IP cameras working but forwarding the ports seems not to work with his current modem from ATT (a Westwell F90 or something). Would the workaround for this be purchasing a third party modem instead that supports port forwarding and stop leasing the Westwell F90 from ATT?

edit: the modem is hooked up to a DI-524 from D-Link and i already forwarded different ports to see if it was specifically port 80, 1024 etc

View 2 Replies View Related

Way To Get Port Forwarding In Server

Oct 21, 2011

[code]...
How do i setup port forwarding in server 2008?? I have heard numerous ways of doing this through windows firewall, NAT and setting up static routes. Not of which i can get working.

View 2 Replies View Related

Port Forwarding In A Cisco PIX 501

Apr 1, 2012

I finally got my Cisco Pix 501 working on my network and everything is working great! However, I do host game servers on occasion and I have a 24/7 FTP server up and as of now, I can't connect to it because the PIX is blocking the ports!I have zero experience with Cisco, so I need step-by-step instructions on what commands to enter to get this thing working!

View 5 Replies View Related

Cisco :: ASA 8.4 And Port Forwarding

Mar 12, 2011

I am very confused now. I got my 5505 for home (basic) and loaded up 8.4(1) fresh. From the inside interface I can reach the internet no problem but I am having issues trying to get my port forwarding to work with torrent. inside host is 10.100.130.5 port is 26883, I have been trying to configure this forever.

View 9 Replies View Related

Port Forwarding Not Working

Jul 7, 2012

I am trying to make a server in the game Halo combat evolved for the PC, but i need to forward 3 ports, ports: 80, 2302, and 2303, i did them all, but it still says they are all still closed, when I scan them or they say, its times out.I have a D-Link router.

View 5 Replies View Related

DLink DIR-601 - ICS And Port Forwarding

Nov 18, 2011

I have a computer connected through wifi to the internet.I then turn on the computer into ICS mode and connect that to my PS3/Xbox.I'm trying to get an OPEN NAT type but just can't seem to get it working.I've read a few different pages and have tried some things but it's never worked.I've heard of bridging connections and the sort but I'm not familiar with it. I just want to get an OPEN NAT on my PS3/Xbox.

View 10 Replies View Related

Configure Dsl Port Forwarding

Sep 25, 2012

To configure DSL port forwarding,I want to configure as remote desktop.

View 3 Replies View Related

Port Forwarding On A Cisco PIX 501?

Apr 1, 2012

I finally got my Cisco Pix 501 working on my network and everything is working great! However, I do host game servers on occasion and I have a 24/7 FTP server up and as of now, I can't connect to it because the PIX is blocking the ports!

View 12 Replies View Related

Port Forwarding On BT Home Hub 2.0?

Feb 14, 2011

I have Infinity so don't know if that's an issue in my situation. I know I'm being "throttled" by BT when doing P2P downloads so limit this to off peak periods.I have made the recommended tweaks to Utorrent to speed things up and finished off today by port forwarding. I tried to follow the tut I was using to the letter but the download became even slower!! You have to enter the port number in the Hub settings but I wasn't sure whether it was a single number xyz or a range 0-xyz or even xyz-xyz. I really hope I'm making sense.I also wasn't sure whether it's TCP or one of the other options I should have selected. I'm currently on Infinity getting 37.4 Mbps download and 1.7 Mbps upload.

View 8 Replies View Related

Cisco VPN :: VPN Port Forwarding On 877?

Apr 6, 2011

We have the above router for a small business and I want to configure VPN to port forward to the server so it can handle the VPN traffic through Routing and Remote Access.I have configured port forwarding on SMTP, RWW and other protocols successfully but VPN will not work.Within the built in web interface on the Cisco it advised that if I want to configure VPN I need to use Cisco Config Pro. I have had a look through this software but it looked to only support the router as the VPN gateway rather than port forwarding to a server.

View 9 Replies View Related

Cisco LAN :: 871 - NAT Port Forwarding

Jul 10, 2007

I have recently purchased a Cisco 871 router. In the GUI from the installed software, I have been able to configure which ports are forwarded to a specified IP address within my local area network. This seems to output a configuration line like this:
 
ip nat inside source static tcp 192.168.1.123 1000 interface Dialer0 1000
 
However, I can only do this one port at a time. Is there a function or command that I can use to specify a range of ports? For example, I would like to forward tcp ports 1000-2300 to the IP address 192.168.1.123

View 12 Replies View Related

Cisco :: Port Forwarding On 5505?

Sep 2, 2012

I have the following configuration in my ASA 5505 and I'm having problems connecting with other players on my XBox.

I think my problem is that I need to forward ports tcp:3074, udp:3074, and udp:88 to my xbox which is at 192.168.2.50 (vlan 3 below).

View 3 Replies View Related

Cisco :: Port Forwarding (NAT) With One Public IP?

Feb 11, 2012

command for port forwarding to a few applications (inside hosts) when you only have one Static IP (Public) which is used for many to one NAT (Overloading)?This is the config for the many to one NAT.access-list 1 permit 172.16.0.0 0.0.255.255 ip nat inside source list 1 interface Dialer1 overload What command is necessary to forward ports to certain applications?

View 1 Replies View Related

CCTV System - VPN And Port Forwarding?

Jun 28, 2011

I am trying to setup Internet based CCTV system on a router that has a VPN network in place. Am i able to forward the Media and Web Ports to the router without interfering with the current VPN settings.

View 4 Replies View Related

Port Forwarding Multi-Fold?

Mar 11, 2011

Before I get into asking questions about the routers, firewall, and static IP though I want to knock out the most base problem. I plugged a computer directly into my cable modem, disabled the windows firewall, tried canyouseeme.org, and couldn't connect to any ports anywhere in the spectrum. I would assume that being plugged directly into the modem that all ports should be wide open. The port I was originally trying to open was 8093. I called my cable provider and the tech told me that I'm not allowed to have port forwarding in a range as high as 8093 without a business account. I asked the tech what range I could use and he said he didn't know. I did some searching on the net and found that on a typical home cable connection I'm allowed ports 1 through 1024, so I tried numbers all over that spectrum on canyouseeme.org and got no response from any of them. Again, this was while plugged directly into my cable modem with an ethernet cable and my windows firewall disabled. From what I know this has to be wrong in some way, as to use the internet at all I have to have ports available. The only possibility I can think of is that maybe canyouseeme.org is flawed in some way. So the first in a long series of questions to come is why am I unable to find any open ports while plugged directly into my cable modem with my windows firewall disabled?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved