TP-Link 300Mbps Wireless :: TL-WR941ND Losses Its Settings?
Dec 25, 2012
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have two(2) WR941ND routers working at my home. The primary has IP : 192.168.1.2 , this primary router is working as an Acess Point, DHCP is OFF, and no wireless security activated. This primary router is connected to a DSL modem+router and DHCP is activated on it.For the secondary router I configred 192.168.1.100 . On the secondary router I have activated WDS function as well as Wireless Security (WPA2) , DHCP is Off on it. This secondary router is to work as wireless bridge + Access Point. You will understand that this secondary router is wirelessly connected to the primary one.I am able to configure all, and all things work correctly for few days at a time.But if at any time the secondary router is switched OFF, and then again switched ON, it seems to have lost al the settings and its IPs, and thus unable to connect to primary router. At such time I am unable to locate /connect my laptop to this secondary router, and it keeps on searching & searching.
View 1 Replies
ADVERTISEMENT
Feb 16, 2013
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP : Bezeq benleumi
I want to setup WDS using my TL-wr941nd WDS router?
View 7 Replies
View Related
Feb 1, 2013
Region : Canada
Model : TL-WR941ND
Hardware Version : V5
Firmware Version : wr941nv3_en_3_13_9_up(120201)
ISP : Teksavvy
This wireless router keeps freezing. It might stay up for 6 hours at the most, then I have to reset it or unplug for 10 seconds to get it to reset. I updated the firmware a few months ago thinking this would solve the problem. It hasn't.
View 2 Replies
View Related
May 6, 2013
Region : Greece
Model : TL-WR941ND
Hardware Version : V5
Firmware Version :
ISP :
Does TL-WR941ND provide support for 802.1x? (It is not mentioned in the product data sheet, but I found here: [URL] that it is supported on the above device.)
View 1 Replies
View Related
Jan 14, 2013
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : TDS
Currently I am using 2 WA5210Gs and a WR941ND to send my wireless connection from one home to another. The original home utilizes a TDS DSL modem/router combo. Everything works great, but then generally withing 24 hours I will randomly drop my internet connection in the second home, but the network is still up and running strong. The modem is not the problem, because I am able to grab a faint signal from the WA5210G AP connected to the modem and access the internet, and the client WA5210G AP is running at full signal. If I power down the router and restart it, the problem is fixed, but happens again within 24 hours. Originally I changed the IP on the WR941 thinking it was an IP conflict with the modem/router, but the problem occurred again. I also tried switching to unicast DHCP, but the problem still persisted. I looked for a firmware update, but couldn't find a newer version..
View 5 Replies
View Related
Jan 31, 2013
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : TL-WR941ND_V2_V3_120201
ISP : Cox
I updated my firmware due to connection issues, now it gets stuck when trying to load the console. I can see the grey pipe separators on the screen, but nothing else. I've tried chrome, firefox, and IE, but still nothing. The wireless AP is active, and i can connect wirelessly, and i can ping it. just cant get the console to show.
View 9 Replies
View Related
Mar 23, 2013
Region : Australia
Model : TL-WR941ND
Hardware Version : WR841N v8
Firmware Version : 3.13.27 Build 121101 Rel.38183n
Model : TD-W8968
Hardware Version: TD-W8968 v1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
I have two routers, a TP-Link TD-W8968 (main & connected to ADSL) and a TL-WR841N (client) and I'm trying to get WDS working over them in order to use my PS3/media player etc at the tv.
1) are these 2 pieces of hardware compatible for WDS? Status of both hardware seems to indicate yes
2) if compatible, what am I missing so devices behind the client router can access the internet connection.
View 10 Replies
View Related
Feb 9, 2013
Region : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel. 54965n
ISP : Toya Lodz
This is already my second model of the router, which got under warranty. The first model had a problem because it brokes off Internet connections. This second model also breaks the connection. I'm going to give it to complain. Before I do it I would like to ask if there are any ways to improve the router without the need to dispose of the device.
View 14 Replies
View Related
Mar 10, 2013
Region : China
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I bought a TP Link router to access internet. Nevertheless the routur interface is in Chinese language which is not convenient for me to set it up.How to change the interface language ? How to upgrade the routur interface to an english one ? (in the website I cannot see firmware for V6).
View 2 Replies
View Related
Mar 25, 2013
Region : India
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.6
ISP :
We need to configure the AP in such a way, only 1 antenna to be used & not other two, to meet some mounting requirements/limitations. Will I be able to do this using any test/debug commands?
Essentially I want this AP to be operating in 1x1 spatial stream, & with no antenna diversity, so that I can connect only 1 antenna & be deterministic about AP using only connected Antenna RF port & not others
With out configuring anything, when I connect only 1 Antenna, I observed that signal is fluctuating on Client Application & causing the applications traffic stream disconnect.
View 1 Replies
View Related
Dec 6, 2012
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version : 3.6
ISP : comcast
what do i need to do to have my laptop access an Iomega EZ networked external hard drive? It is not my firewall on computer so Norton said it is the router.
View 1 Replies
View Related
Feb 20, 2013
Region : Singapore
Model : TL-WR941ND
Hardware Version : V3
I would like to connect a device (dataloger that sends data to a remote server via internet) which only has LAN port to a wireless network on the location. I managed to do this once with WA901ND configured in Client mode (WA901ND acts like a wireless card for this data loger).Does WR941ND support this feature (which feature should I use?) or should I buy WA901ND again?
View 7 Replies
View Related
Apr 9, 2013
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
We are trying to use a TL-WR941ND purchased about a month ago, but it keeps hanging, usually within a day or so of operation.To be clear: by "hanging" I mean the device stops providing wireless services (its SSID is no longer visible in WiFi clients) and becomes nonresponsive to pings or control access attempts (via settings web page) from the internal network connections.The device is used in a very simple scenario, where it's being employed as a simple access point, not as a router. As such, the device's configuration is as follows:
* WAN interface is configured with a dummy static IP (10.10.10.10/24) with gateway and DNS set to the internal IP address of the actual routing device connected to the external world.
* LAN interface is configured with an IP address inside the actual internal IP subnet (192.168.1.0/24).
* DHCP is also disabled as this service is already provided.
* Wireless settings: radio enabled, SSID broadcast enabled, WDS disabled, 11bgn mixed mode, auto channel width, max TX rate, channel 7 (manually set). Using WPA-PSK security.
Rest of the settings are unchanged from their default values, as the device isn't being used as an IP router by any client - just as a WiFi/Ethernet layer 2 bridge. We're using what appears to be TP-Link's latest stock firmware for the device.The settings described above appear to provide the connectivity required by the WiFi clients. However, the device continuously hangs within a day or so of operation, requiring someone to physically attend to the device and cold-restarting it (disconnecting it from power and reconnecting it) to regain an operational state.
After performing a cold restart, the system log shows nothing beyond the startup entries: "System started" entry followed by security info entries regarding enabled protocols. Then the device appears to work well for a while, until it hangs again, forcing again someone to attend to the device, etc.
View 6 Replies
View Related
Jan 2, 2013
Region : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have a problem with files sharing via wi-fi. I can not share files over the network using wi-fi connections. While the network is the cable connection sharing is available. The network also acts as one computer is connected by a cable to the router and the other via wifi. But if the two computers are working through wifi network does not work. Are there any settings in the router, which can cause blocking calls via wifi?
View 1 Replies
View Related
Feb 2, 2013
Region : United Kingdom
Model : TL-WR841ND
Hardware Version : Not Clear
Firmware Version : 7.1
ISP :
failed to verify router settings
What's wrong with my router?
View 1 Replies
View Related
Dec 17, 2012
Region : Others
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I have 2 TP-Link # 941NDs at my home. ( version 3.6 )In the new ( second ) TP link, i activate WDS - Wireless Bridge. And configure it to through Wi-Fi connect with earlier TP-Link, and also to act as router to cater to PCs within its range. IPs are set as per of same family as that of primary TP-Link, and further, DHCP been de-activated as well. Have sent WEP security as well.It performs correctly for the time, its stays ON, but when its switched Off, and then On again, it is not able to connect to the primary TP-Link and thus not able to serve its client PCs.
View 4 Replies
View Related
Jan 29, 2012
I have a TP-Link (TL-WR941ND) wireless router in my living room and I want to expand my connectivity to get to the bedrooms area. I have a D-link (DI-524)wireless G router I want to take advantage of. How can I connect the two routers (no cables to be used) together so I can have acces to the internet from my room?
View 1 Replies
View Related
May 10, 2012
I have a D-LINK DIR-300 router with 4 LAN and WI-FI. It's acting very strange lately. It is connected to a UPS battery and the one LAN connection is in surge protection.Here are the symptoms:
-Every 2 days it just loses connection. I have to reboot it so to make the connection working. It's a little bit annoying after awhile.
- One day one of the LEDs started like fading away and came back up (the one that signals the LAN connection).
- When all the LEDs were properly working and the connection was good also, I moved the the power adapter cord a little bit at some part (I didn't plugged it out) and some of the LEDs gone (Internet connection LED and Wireless) but all the other LEDs were working. Of course there wasn't connection either.my OP is Ubuntu 12.04 and the connection DHCP is well configured.
View 1 Replies
View Related
Dec 26, 2011
I have a D-Link DIR-615 Hardware Version: E3 Firmware Version: 5.10 and I am using this as an access point with the DHCP disabled (secondary router) and my primary router is located down stairs and it is also a DIR-615 Hardware Version: B2 (192.168.0.1) and this issue didn�t develop until later over time and I have made absolutely no network configuration or ISP changes at all the internet has been working fine confirmed with Time Warner Cable and for more than six months and I out the DIR-615 Hardware Version: E3 Firmware Version: 5.10 router has been bringing down the entire network/internet access and I can confirm this router is causing the network/internet to go down and windows notification will say the network only has limited access and I am also unable to access the router page (192.168.0.2) state I have to remove it and restart it D-Link can take a look into this issue I believe this might be a bug and I confirmed on the website that this is the latest version.
View 15 Replies
View Related
Jul 19, 2011
I have had this wireless router for 3.5-4 months, and it has been working fine up until now.It either runs VERY slow and losses connection often or will not connect at all. I could be sitting beside the router or across the room with the same results. i have even tried connecting a cord from the laptop to the router, but it makes no difference. If it makes any difference we have a PS3 that is connected via wire to the modem and it works just fine, never loses connection. We have used both at the same time since we got it and it was fine up until a few weeks ago.I have tried reseting it and unplugging everything and rebooting the computer and that had no effect. I also tried reinstalling the router on the computer using the setup disk and resetting everything but that did not do anything either. I have an Acer Aspire laptop MTS ~ DSL Modem?
View 4 Replies
View Related
Mar 25, 2013
Region : Germany
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 8.1
ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
View 2 Replies
View Related
Mar 30, 2013
Region : Others
Model : TL-WR841ND
Hardware Version : V7
Firmware Version :
ISP :
my ip address is not static i use no-ip sevice to get dns how to set my tp link for wake on lan
I managed to update ddns in my tp link How do I go from here?
View 1 Replies
View Related
Apr 22, 2013
I am currently running a TL-WR851ND Wifi Router whith the latest build 3.13.27 Build 121101 Rel.38183n() published last November 2012. Now is there any new firmware?
View 1 Replies
View Related
Dec 10, 2012
Region : UnitedStates
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : latest
ISP : Time-Warner
Just purchased the WR940N to use as a wireless bridge. I expected to be able to have the router join my wireless network, and provide Ethernet connectivity to 4 devices behind it. But I'm missing something in the configuration. I can get it on the wireless network, and manage it via the wireless network. But devices plugged into the Ethernet cannot get out to the Internet. Basically, I have a 192.168.1.x network, and the router is node 192.168.1.3 on the wireless network. I've turned off the firewall and DHCP on the router. The Ethernet devices behind it get an address from my network, but the router inserts its own address in as the default gateway, and my Ethernet devices do not have a route to my 192.168.1.x network, despite having an address on it.
View 4 Replies
View Related
Dec 21, 2012
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP :
I have a WR1043ND
Firmware Version:
3.13.12 Build 120405 Rel.33996n
Hardware Version:
WR1043ND v1 00000000
I tried to connect a WD MyBook Essential 3tb hdd NTFS, but it never recognized it. Of course, I connected it with the external power supply.With a 15gb pendrive FAT32 it works OK.
View 14 Replies
View Related
Nov 26, 2012
Region : Russia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :
Region : Russia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : wr1043nv1_ru_3_13_10_up(120614)
ISP : netbynet
Connection to a router on a cable speed of dowstream-50MBit/s, upstream-3Kbit(!) wifi-dowstream-50MBit/s, upstream-3KbitA cable directly in the personal computer to 70 Mbps there and back.Measured speedtest.net, and as [URL] The matter is that even elementary with an investment it is impossible to send mail - I am connected by different devices-2 of the laptop and 2 smartphones - the same. Technical support of provider already talk sense only in a router. Insertions updated, changed - the same( Firewalls are disconnected, any more don't know what to do and where proceeding speed and all digs-is killed. Russian forum TP-Link is idle.
View 3 Replies
View Related
Apr 16, 2013
Region : Others
Model : TL-WR843ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I buy TL-WR843ND router to provide a better signal upstairs. Router is in wisp mode with statick ip. Everyting work good. I have routed home network with mikrotik. And everyting was setup with priority on mikrotik for each user separately. With this router every user connercted on it was hidden behind TL-WR843ND. How to disable NAT on TL-WR843ND to use routed network?
View 5 Replies
View Related
Dec 26, 2012
Region : Austria
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
unfortunately I've lost my device pin and I've reset my device.can I get the device pin on a other way? on my invoice there is no information about that.
View 1 Replies
View Related
Nov 29, 2012
Region : UnitedStates
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : WR1042ND v1 00000000
ISP : comcast
I have a machine called 'survtest' on my lan with a permanent ip addr of 192.168.0.112. I can't ping that host by name from any other machine on the lan, although I can ping the ip address. Not only that but this machine appears in the DHCP client list within the router with its name 'survtest' and correct IP addr.
There is another machine on the lan called 'bsd' that also has a permanent IP addr of 192.168.0.110. It can be pinged by name from any other machine on the lan. However it does not show up in the DHCP client list at all.
Neither of these machines can be pinged by name from within the tplink admin diagnostic screen.
View 2 Replies
View Related
Jan 22, 2013
Region : Netherlands
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP :
Is it possible to use a VPN service such as hidemyass on the TL-WR1043ND without installing the DD-WRT firmware?
View 2 Replies
View Related
Nov 29, 2012
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]
View 4 Replies
View Related
Nov 29, 2012
Region : Germany
Model : TL-WR841ND
Hardware Version : V3
Firmware Version : 3.13.18
ISP : [url]...
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways! I have already tried MAC Clone for WAN but nothing changes.[code]....
View 1 Replies
View Related
Mar 22, 2013
Region : Germany
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
I bought 2 router but WDS wont work. If i set on both WDS on they wont connect themselves wireless statics show 0 stations if i only set one to wds then there is one station connectet but it only functionates in one way. I set WDS on router A on and plug a lan cable to my pc i can configure Router B if i plug in B my lan cable i cant configure router A. If i plug my existing network on B and mein PC on A in then i can config all my router in the network but inet wont work -.- what did i false? or have they a disfunction? I tried it withouth wlan security and with wpa2 no succes
View 8 Replies
View Related
