Region : UnitedStates
Model : TL-WR940N
Hardware Version : V1
Firmware Version : TL-WR940N_v1_120201
ISP :
Just bought a TL-WR940N and it was always loosing connection and freezing / locking up. I upgraded to the latest FW from the link below URL but it still freezes and loses connection to devices after 8-12 hours, keeps hanging up and pages sometime don't load.
Region : Poland
Model : TL-WR940N
Hardware Version : V2
Firmware Version :
ISP :
few days ago i changer my work etc . so i tried to connect to worknetwork wireless but it was connected for 10 minutes and then this message just appear "Wireless network connection doesn't have a valid IP configuration" there is also public network the same ,, connected for few minutes then when i connect again always the said limited access but with my home work is working perfectly but with work or public network always get this msg after few days searching in google nothing useful ps all computers in company are working perfectly with this wireless connection but my laptop no i have this message in router setting WAN port is unplugged,, check photo here [URL] router model TL-WR940N im useing win7 64 hp pavilion dv7 anti virus > deleted firewall state > off IP helper > disabled when i was connecting to public network this is result of Xirrus WI-FI inspector [URL]
Region : UnitedStates
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : latest
ISP : Time-Warner
Just purchased the WR940N to use as a wireless bridge. I expected to be able to have the router join my wireless network, and provide Ethernet connectivity to 4 devices behind it. But I'm missing something in the configuration. I can get it on the wireless network, and manage it via the wireless network. But devices plugged into the Ethernet cannot get out to the Internet. Basically, I have a 192.168.1.x network, and the router is node 192.168.1.3 on the wireless network. I've turned off the firewall and DHCP on the router. The Ethernet devices behind it get an address from my network, but the router inserts its own address in as the default gateway, and my Ethernet devices do not have a route to my 192.168.1.x network, despite having an address on it.
Region : India
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.13.27 Build 121101 Rel.38183n
I have bought TP-Link TL-WR841N 300 mbps router. I have 20-25 wireless clients but only 15 wireless clients are able to connect to the router. Is there the limitation on numbers of wireless clients can connect to the router?
Region : Others
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.11.3 Build 100408
ISP : Telekom
the SYS light, keeps blinking is that normal?
Region : Others
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : TL-WR1042ND_V1_130117
ISP : Optic konvertor DHCP mod
I bought TL-WR1042ND and I have problem. After 2 hours, the router loses all connections. Lights that everything is OK, but he can not connect to any site on the Internet or LAN. Even nor to 192.168.0.1 Only search for the host.
I have a DHCP internet. DNS 8.8.8.8 I disabled firewall and all I do not need, but nothing worked.
Region : Others
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I have 2 TP-Link # 941NDs at my home. ( version 3.6 )In the new ( second ) TP link, i activate WDS - Wireless Bridge. And configure it to through Wi-Fi connect with earlier TP-Link, and also to act as router to cater to PCs within its range. IPs are set as per of same family as that of primary TP-Link, and further, DHCP been de-activated as well. Have sent WEP security as well.It performs correctly for the time, its stays ON, but when its switched Off, and then On again, it is not able to connect to the primary TP-Link and thus not able to serve its client PCs.
Region : China
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I bought a TP Link router to access internet. Nevertheless the routur interface is in Chinese language which is not convenient for me to set it up.How to change the interface language ? How to upgrade the routur interface to an english one ? (in the website I cannot see firmware for V6).
Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : TL-WR1043ND_V1_120405
ISP : BT Infinity (1)
I have a TL-WR1043ND v1 with the latest firmware installed TL-WR1043ND_V1_120405.I loose access to the router (can't see web page, can't config, can't restart).I have a Linux server on the Ethernet, and uplink through 200Mbps powerline adapter to the BT Infinity modem. A few other devices on the wireless.The router works well and I prefer it to the BT Home Hub 3 for fiber because it proved to be faster in many cases as tested.But after a few days the web interface becomes inaccessible. It's like the web server died or something. Browser says connection reset, if I try telnet to port 80 says connection refused.Actually I just did a full netcat scan (sudo netcat -z -v -192.168.1.1 1-65535) and all ports say connection refused.Ping works - I can ping it allright.DHCP server works too, just restarted a computer and got IP from the router.Port forwarding works as well and DynDNS seems to work as well as my ISP changes the IP periodically and I can always find the updated one.All works - exept I can't access the router in any way!If I restart (remove power and plug it back in), it boots and I can access the router again.So restarting won't work remotely, I actually have to go home to re-plug it!
My D-Link DIR-300 very often loses connection on wired and wireless connections. It stops connecting to Internet randomly i.e. any URL typed in from the browser times out.I connect various devices such as desktop, laptop, ipad2 over wired and wireless connections and the behavior is the same from all devices when this problem occurs. If I make a direct connection to the DLS modem, it works fine for the whole day, without these issues.I also observed IP address conflict messages and my desktop does not connect to Internet if I am running VPN on my laptop, at the same time, occasionally.When this occurs, I am able to login to the router and can see the WAN status and the DHCP address being allocated to the router. I can even do DHCP release and renew, but that does not fix the problem.
View 3 Replies View RelatedRegion : Canada
Model : TL-WR700N
Hardware Version : V1
Firmware Version : latest
ISP : Cogeco
I have a WR700N set up in bridge mode so as to provide a wifi signal in far end of our home. I used Bridge so we can tell which router we are connecting to. So we have two SSIDs (MySSID1 and MySSID2) Both with secure log-in. This works fine for about a day, and then disconnects. I then have to mess with the WR700N by plugging it in and out, maybe logging into it and changing something. Then it will work again - for a day
I updated the firmware with no change. Main router is a Dlink 615 with IP of 192.168.0.1. connected to cable modem. TP-LINK is set at default of 192.168.0.254 and gets a wireless signal from dlink.In an attempt to improve situation, I now have both units set to channel 11 and with fixed 20Mhz channel width. b/g/n on TP and g/n on dlink.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Comcast
The 5 ghz connects fine for multiple machines however machines on 2.4 simultaneously lose their connection to the internet, sometimes saying it is still connected to the internet when it is not and sometimes losing connection with the router entirely. The 5ghz still works when this happens.
So I've bought a D-Link 815 on 21st June(day before yesterday) and my connection drops every 10-12 hours and i have to close and open the router(the 192.168.0.1 site won't even work)...i'm using PPPOE connection..
I've bought a D-Link because i heard it's the best on the market and i play online poker so i need a stable connection all day long and more important i need my IP to remain at one value for a long time and not change every 12 hours(i have dynamic IP)
Region : Australia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I am trying to get a windows 7 laptop to connect to a TD-W8970.
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Region : Canada
I have a T L-WR1043ND v1.9 with the latest factory firmware that I recently purchased. Ran fine for a couple of weeks. Now my WAN connection seems to be dropping. I get an IP and DNS from the ISP but I cannot ping anything (google etc...) past the router. I have to hit the detect button or release and renew the IP in order to gain access. Then after a few hours or a day the issue reoccurs.
Region : Malaysia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.13 Build 120605 Rel.38634n
The connection is slow when I connect my notebook to the TP-Link TL-WR1043ND wireless router. If I connect my notebook directly to to the ISP modem, the connection speed back to normal.
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : TDS
Currently I am using 2 WA5210Gs and a WR941ND to send my wireless connection from one home to another. The original home utilizes a TDS DSL modem/router combo. Everything works great, but then generally withing 24 hours I will randomly drop my internet connection in the second home, but the network is still up and running strong. The modem is not the problem, because I am able to grab a faint signal from the WA5210G AP connected to the modem and access the internet, and the client WA5210G AP is running at full signal. If I power down the router and restart it, the problem is fixed, but happens again within 24 hours. Originally I changed the IP on the WR941 thinking it was an IP conflict with the modem/router, but the problem occurred again. I also tried switching to unicast DHCP, but the problem still persisted. I looked for a firmware update, but couldn't find a newer version..
Region : Austria
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.4 Build 110429 Rel.36959n
ISP : TPG
I've got a problem with the wireless dropping out randomly. It may take a week before it stops or a couple of hours. I originally thought my microwave oven was swamping the signal when we used it so I relocated the router much further away but this hasn't changed anything. I can still log in to the router from a computer on the wired ports and reboot the router. It also thinks the wireless is working but everything looses connection to it. We have 3 laptops and 4 phones that use the wireless and they all cannot connect when it goes down. This is only a new device - less than 6 months?
Region : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel. 54965n
ISP : Toya Lodz
This is already my second model of the router, which got under warranty. The first model had a problem because it brokes off Internet connections. This second model also breaks the connection. I'm going to give it to complain. Before I do it I would like to ask if there are any ways to improve the router without the need to dispose of the device.
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : AT&T
Every 5 to 7 days my router loses connection with WAN (ISP modem) but connection over LAN is fine. It seems that 1043ND tries to connect to DSL modem from AT&T by username and password (that does not exists) instead of doing Dynamic IP. I understand that AT&T modem is of type of PPPoE but there is not a password or user id and connection must be dynamic. Page 192.168.0.1/logininfo of modem complains that I was trying to login with incorrect user id password. Every time I have to
1- connect the modem directly to my computer so the modem resets.
2- I have to reset 1043ND to factory default, reboot, and connect cables back how they were, Then go to WAN page do a release and renew to get connected to WAN again.
Region : Spain
Model : TL-WR842ND
Hardware Version : V1
Firmware Version : 3.12.22
ISP :
I am trying to set up a VPN access to the office Windows network by setting the pptp options in the WAN area of the networks settings.
I have entered the public IP address of the office network and also the username and password required by the system. When clicking on the connect button the router attempts to connect but then returns a "disconnected" message.
Region : Latvia
Model : TL-WR841N
Hardware Version : V8
Firmware Version :
ISP : A/S Balticom
recently i bought wireless router TL-WR841N and there hasn't been a day or should i say few hours without restarting/turning on-off.I have cable(no modems,etc)Longest time it has ran without restarting was around 20hours.The problem is it RANDOMLY looses connection like this , but it's not the only problem , mostly when i leave computer and go to sleep or other business i leave router turner ON (no else have access to it and no one touches it), when i come back it just does not connect to internet, it shows that everything is fine , but i have no access to internet.This happens to all connected computers.I have dynamic ip I have russian version of windows xp sp3 , but i think everything is pretty understandable here. connection timed out/request timed out
Code:
Microsoft Windows XP [Версия 5.1.2600]
(С) Корпорация Майкрософт, 1985-2001.
C:Documents and SettingsГеоргий>ping -t [URL]
[code].....
FYI the problem is not in my computers(i tried setting up wireless networks from 2 different pc's) and i'm pretty sure it's not ISP's fault too(everything works fine through cable) , because this never happens with other wireless networks, etc.
Region : Germany
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 121127
is it possible to use the Print Server on the TL-WR1043ND without installing the "Printer Controller Utility"? I have a HP LaserJet 1022 (in compatiblity list) connected which is recognized by the TL-WR1043ND. I want to connect the printer manually to my Windows PC using standard tcp/ip port, but I can't get it working. I tried RAW with Port 9100 and LPR with lp1. What are the right settings??
I am having a very frustrating issue with my wireless D-LINK 615 (firmware 5.0.1 NA). The internet connection drops constantly every 2-3 hours. Here are the settings on my router:
Cable modem
Modem Motorola Surfboard model SB6120
Code...
This seems to happen after I upgraded the firmware. Before that, did not get a complaint from my children or wife. Before I squeeze the last drop out of this lemon.
I've recently bought a TL-WR1043ND & i'm trying to connect my Sky+ box to the Internet. When I connect the box directly to my broadband router all works OK. When I connect via an Ethernet connection on my TP-Link router - it get's an IP address from the router but it will not connect to the internet.
View 4 Replies View RelatedRegion : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Netherlands
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : Ziggo
I currently have a issue with my TP-link WR941N.When I first connected the router I had a good internet speeds of about 70 mbps. My max provided by the ISP is 120Mbps but 70 was acceptable for me. Recently however the connection is terrible. I regularly have a speeds of 6Mbps via the router, When i directly to the modem via kabel I get a speed of 120Mbps. Therefore I ruled out that the connectivity problem is due to my ISP.
Region : Netherlands
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : V1_120405
ISP : UPC
After buying and installing i get no wlan/wifi connection.I do have internet by ethernet, the laptops and ipad sees the wlan/wifi but get no connection? Resetting re-installing manualy or with the wizard doesn't work.
Region : UnitedStates
Model : TL-WR841N
Hardware Version : V8
ISP : ATT
I get this new router TL-WR841N from amazon.com, I get no signal/internet connection on my computer when I install/connect the router using the installation min CD (same procedure at listed here: url...The DSL connection is good, since I get internet connection when I connect my modem directly (without the router) to my computer. My modem is the old Siemens SpeedStream 4100 with IP Address of 192.168.0.1 from ATT.Is my router deficit ?
I have a fibre optic internet connection, the modem being connected to the TP Link wireless router. The set up works fine most of the time, but at times all the computers connected lose internet connection. The ISP says everything is fine from their end, and locally we are all connected to the wireless router just fine when this happens. I usually just unplug the modem and the wireless router from their power, in order to reset everything, and this seems to solve it.
View 4 Replies View RelatedI have a dir-825 connected to Cable modem and a dap-1360 connected I have both wireless and wired clients.If get a ip address conflict and the the dir-825 connection fails from the cable modem and nothing seams to restore that connection, i reboot both route and modem and make sure no client are on. The only way i can figure out how to restore the router is to reset and reinstall from factory state.I can recreate this on 2 different router "825" with factory and updated firmware.I have removed the wireless extender form the picture and this issue has stopped, it might be the extender of a client off the extender. But everything uses DHCP so I'm not sure why ip address conflicts could cause this issue.
View 2 Replies View RelatedRegion : Belgium
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Telenet
I've just bought a TP-Link TL_WR1043ND and when I was configuring the wireless settings first I had a +- 40Mbps connection,a little later the connection dropped to 4Mbps and was constantly dropping the speed.Sometimes it went to 15Mbps and then it drops back to 4Mbps.Right now its only 1Mbps.
Configuration:
Wireless channel: 11
Mode: 11bgn mixed
Channel width: Auto
Max tx rate: 300Mbps
Wireless router radio and SSID broadcasting enabled
[code].....
Region : Russia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
can You create firmware for Hardrive 4 TB connection to router TL-WR1043ND via USB.
It took a while but I've had my 1522 running well for several days. However, if I power down and then power up the 1522, it never reconnects. The bridge mode light flashes 5 times, then - nothing.
So, I have to disconnect everything, bring the 1522 back to my main PC, attach it, let it connect properly, then unattach and re-attach at it's use site.
(I'm using a static IP address and a Cisco E3000 router working perfectly with all my other stuff. Firmware v1.31)
