Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.5 v000e.0 Build 121225 Rel.42874n
ISP :
Just checked and port 7547 which is used for CWMP is open by default even if the settings are showing disabled. Try http://"external IP address":7547
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
Another query regarding diagnostic test and Test DNS Root. It always fails why?
Region : UnitedKingdom
Model : TD-W8980
Hardware Version : V1
Firmware Version : 2013 firmware update
ISP : PlusNet
I changed the local port to 8080 for accessing the web logon page (i.e. 192.168.1.1) instead of its default port 80.
[code]....
Region : Ireland
Model : TD-W8980
Hardware Version : V1
Firmware Version : 0.6.0 0.6 v000 build 130303 rel. 38108n
ISP : Eircom
Bought this adsl router on Friday and since then I have been experiencing random frequent wireless dropouts, router appears to reboot at this point too, Internet drops out too. Wireless drops as I hear the beep from my airplay speaker reconnecting. Any one have these issues too, tired changing channels, then back to auto again, still no joy.
Region : Others
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
Region : Sweden
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
opening of some ports 25565 for minecraft so i can host games. i have try so solve this by my self but with zero progress. did enter the advanced setup and then i pressed on the NAT category and then i pressed on the ADD button and enter the following" [URL] and then i used a port checker to look if it worked but did not work?
Region : SpainModel : TD-W8968Hardware Version : V1Firmware Version : got an ADSL connection with Movistar Spain, static IP. When I configure the TD-8968 all works well, it syncs but does not connect to internet. When I diagnose the connection the modem pass tests at ATm level but is not able to find the default gateway. I got another modem (the one to be substituted with the 8968) that it works with the configuration I am triying to use. Is there some step I am missing or is the modem faulty?
View 1 Replies View RelatedRegion : Italy
Model : TD-W8968
Hardware Version : V1
Firmwae Version : latest
ISP : telecom italia business on ipatm
How to Forward an external wan port like 49150 to lan ip on port 22?In the control pannel I can set only one port , and this port will be the same where the connection will be router to the lan ip ,therefore If I set the port 22 , the connection will be natted to the 22, but how to set a different external port to a specified different lan ip port?
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : 5.0.0
ISP : Beam Telecom
I recently bought this device in hurry . My ISP has directly connected RJ45 cable to my laptop .So i need to use this device for sharing internet to my wireless devices .IS it possible to convert Rj45 to Rj11 if so let me know the process .I have seen interenet about converting lan port to wan for TD-W8960 device . but GUI administration is quite different for my device .
Region : UnitedKingdom
Model : TD-W8980
Hardware Version : V1
Firmware Version : 0.6.0 0.6 v000e.0 Build 130304 Rel.38108n
ISP : Plusnet
Have spent most of the day trying to get port forwarding to work! U an trying to run a mail server and am forwarding ports 25, 110, 995 to a PC on my LAN, only problem is the ports never get there. I can connect quite happily if I wire a laptop to the router BUT as soon as I try to connect from externally either by mail.domainname or IP I am not able to connect. Using telnet I can't connect to the ports either. If I forward port 80 I still connect straight to the router rather than trying to connect to the mail server for webmail. At the moment I am having to forward all mail from the server to a google account just to read it!!
Region : Vietnam
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 build 120524 rel 05221
ISP : VNPT
Where is the PVC Ethernet Port Mapping in TD W8961ND?
Region : Italy
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120720 Rel.09287
ISP : alice
A couple of weeks ago I have bought a TD-W8961ND in replacement of my old modem/router (of another brand, to upgrade from Wireless G to N). I tried to replicate in the new router something similar to my old setup, so I programmed Virtual Servers (under the NAT menu) with the following rules: NATRules.jpg in an attempt to:
- grant access from "outside" Internet to my web server
- have a Wakeup-On-LAN from "outside" Internet ..etc.. without success. Please note that:
- I have successfully setup a DDNS server to reach my modem router from outside
- as for WOL, I defined my subnet mask as 255.255.255.128
- I have not set any other rule, nor in NAT, nor in routing or other
- I tried also with firewall disabled
- I do my testing by means of a smartphone with wireless disabled and Internet connection via mobile service provider
- Both the above mentioned functions were working with my old modem/router (and still work on LAN), and I have not changed other things (PC setup etc)
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
The Remote Management Port is not working correctly. For whatever port I set, it will uses port 80 to access.
Region : Others
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP :
I've been using the W8968 for a while now with the default firmware out of the box. Everything was working fine, except that during a hard reset (power off-an-on) all my port forwarding settings were gone. This was so annoying that I decided to upgrade the firmware to 120926. Now the settings don't disappear, but the port forwarding stopped working. I've tried to connect from the outside to all of the ports that I opened on the router, but it kept on saying the port is closed (even though it appears on the port forwarding list and the status is "Enabled"). The router firewall is also disabled.
Region : Others
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0
ISP :
My router is TDW8961ND
The firmware version is 3.0.0
The hardware version is 3.0
I am trying to have a virtual http server at port 80 but when I do this and save, I get this message: "Notice: The WAN HTTP port of CPE will be chaged to 8080 if submit successfully."Then after that I cannot access the server at port 80.
Region : Greece
Model : TD-W8961NB
Hardware Version : V2
Firmware Version : 2.0.0 120823
ISP : otenet
The problem is that the voip is not working. I have 2 offices with adsl connection. A is the central office and B is the branch office. The installation is old with deferent ADSL modem-router(Zyxel). The zyxel at the A office was damaged so i had to change it with Tp-link. The potology with ip and cables is the same. I tested the port forward for voip (port 1720) with telnet from outside of the office and responds correct. When i try to call from the A office to B office it seems that i can not connect. When i call from B office to A office the phone is ringing and i can not hear office B but office B hear office A. When i use the old modem router at the office A everything is working fine but the modem-router works just for a while so i have to change it. I closed the firewall but the problem is still the same. I talked with the local distributor and they tolded me that i have to correct the configuration. At the interface setup is chosen the dynamic at the section get ip and not static as i should do. The is a problem there. The configuration asks me the subnet mask and gateway. I do not know the subnet mask and either the local distributor and the local internet provider cannot assist. The internet provider told me to use at the subnet mask 255.255.255.240 and at the gateway the ip of the router. I did that but when i did i lost the internet connection. I have to mention that i make some other port forwards to my SBS2003 server and like remote desktop, vpn connections and https that works fine. The only prolbem is with the vpn port forwarding.
Region : Australia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0
Build 120926 Rel.27100n
ISP : Bigpond
I am trying to setup port-forwarding (6360 for IP 192.168.1.111 & 6361 for IP 192.168.1.112) on this TD-W8968 modem. But when I test it on [URL]. I get a message "connection refused".
I have a DNS-323 that I can;t get my FTP to work.For some reason no matter what I try I can't open ports on the DIR-655I have the virtual server set as such. [URL]. Checked with open port tool.
View 6 Replies View RelatedI recently upgraded my DIR-655, H/W Version A3 from 1.21 w/o SecureSpot to 1.35NA. My understanding this that this version isn't supposed to have any SecureSpot support. However, whenever the router is rebooted, the logs contain an entry that reads:
Bsecure remote access enabled on port 8098.
I have tried to open ports, but if I use the [URL], I just get the closed. I have tried to use the Viritual server function, but can`t se to get it open.
On my old, D-Link I also had something cal port forwarding, this is not here. Here is a link to an emulator of the router: [URL]
I cannot open the config page of beetel adsl2 router using 192.168.1.1I have connected my laptop to router via Lan cable. Now when I give the ipconfig, I get some random IP and does not get the default gateway: Autoconfiguration IPv4 Address. . : 169.254.129.188 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . :I cannot ping 192.168.1.1 nor 169.254.129.1 thus the web page of router cannot be opened.This all happened after I reset my router.
View 3 Replies View RelatedRegion : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
Region : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
[code]...
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
According to inSSIDer the router seems to be using two wifi channels (10+6) and inSSIDer is recommending to move to a standard channel (1,6,11).
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : BT Broadband
Just got myself a new Modem/Router (TD-W8960N), and it wasn't until I had it all up and running that I realised it didn't have USB port on the back.Anyways, I was wondering how I could go about fixing this? I stumbled upon this (TP-Link TD-8817) on Amazon and wasn't sure if I could attach this to it in bridged mode or something. This has the USB socket I need. If this was all I needed, how do they connect together? I have a BT connection btw.Also, I have a Justop Android 4.0 TV Box (media player). Would this be able to see the HDD for streaming movies.
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version :
ISP :
problem with filtering
Region : Syria
Model : TD-W8901G
ver 6.0
54Mbps wireless G ADSL2+:
I used the url filter utility inside the router program. I put some url for example www.google.com, I wanted to try the filtering cababilty, Later I deleted all these adresses , but unfortunatley it keeps telling me the following message: "The system returned: (110) Connection timed out The remote host or network may be down. Your cache administrator is webmaster@proxy1."
So here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
A external scan has reviled that I have an open port. For security reasons I want to close it. I do know the port number.
View 7 Replies View RelatedI use a wired network connection to my neighbours Vodafone Modem (We share his monthly cost). I also have a TP-LINK 54M Wireless ADSL2+ Router from a previous broadband contract with a landline phone company. Is it possible to reset and configure the TP-LINK Router to act as a relay unit, connected to the network cable, so I can then use my laptop elsewhere in the house?
View 3 Replies View Related