TP-Link ADSL2+ Wireless :: Ddns Used Behind TD-W8970 Is Not Working

May 4, 2013

Region : Others
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :

I just set up DDNS for my home, and also set forwarding port 5000 for my NAS with an specific IP address 192.168.1.xx. Then, I use my office Internet to call DDNS xxx.dyndns.org:5000 to connect the NAS in my home, It is working OK (from outside to home) However, if I call xxx.dyndns.org:5000 by my home Internet, it is not working (from inside home to home). But if I directly call NAS' IP address 192.168.1.xx:5000, it is OK to reach it. So I think, DDNS used behind TD-8970 (inside home) is not working. TD-9870 is not forwarding port.

I don't know what do I miss in setup this WD-8970.

My previous Zyxel wireless router modem can allow me to us DDNS behind it with out any extra setting. Is it possible that there is still some bug in Firmware of this TD-8970?

ADVERTISEMENT

TP-Link ADSL2+ Wireless :: Using A TD-W8970 With A NAS?

Feb 28, 2013

Region : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :

Im having issues setting up port forwarding with my Synology NAS.

My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.

The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.

Is there some button i need to check or switch on the modem?

View 3 Replies View Related

TP-Link ADSL2+ Wireless :: Can't Connect With TD-W8970

Feb 25, 2013

Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : TD-W8970_V1_130201

I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.

[code]...

View 5 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8970 - NAS Not Being Seen On Network

Apr 16, 2013

Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP : Virgin

I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.

The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8970 Freezes Randomly

Mar 24, 2013

Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Infostrada

My TD-W8970 freezes randomly, sometimes several times a day, sometimes less, but now the problem it's more frequent and I suppose it could be generated by some internal component that could have a abnormal behavior.Anyway, this happens in different situations, either using all the functionalist, or being only on and in idle state. Last time was few minutes ago, when all the system were shuttled down and only router was on.

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8970 - TP-LINK USB Printer Controller Is Causing BSOD?

Apr 12, 2013

Region : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :

Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.

However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.

I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).

To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.

The router print server is a nice functionality and I really want to use it.

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: Can't See Synology Nas Using VPN Tunnel Between TD-W8960N And TD-W8970

May 3, 2013

Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 2.1 v000c.0 Build 130415 Rel.34164n
ISP : plusnet

I have setup 2 vpn tunnels from my TD-W8970 to places that use TD-8960N (Firmware Version: 1.4.0 Build 110921 Rel.17774n Hardware Version: TD-W8960N v3 0x00000002 )and I can ping and connect to any ip used at their end but they can only ping 192.168.1.1 which is my router and not 192.168.1.104 which is my Synology DS212J that they need to access.

Both tunnels are similarly configured:

Tunnel 1 on my TD-W8970
IPSec Connection Name: Tony1
Remote IPSec Gateway Address(URL): 89.240.xx.xx
Tunnel access from local IP addresses: Subnet
IP Address for VPN: 192.168.1.0
IP Subnetmask:255.255.255.0

[URL]

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8970 - VPN Disconnection But Tunnel Still Shows As Up

Apr 15, 2013

Region : United Kingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : O2

I have sent the following trouble ticket to TP Link Support hoping they can shine some light/fix a VPN issue I am experiencing with the TD-W8970 router.

Please see the text below.........

I have 2 tunnels set up on my TP Link TD-W8970 and although both of these work for a a while, they both drop out after 24-36 hours for no apparent reason. The tunnels still show as "up" in the router, but I lose PING and connectivity to my remote systems. The only thing that seems to fix this is to reboot the router.

I have tried the tunnels with and without "DPD" (Dead Peer Detection) enabled and the results are the same.

I have 2 other friends who have the exact router with the same firmware (latest version), and they too have the same issue.

There is nothing in the logs showing any disconnection of the VPN, and as I have mentioned, the tunnel still shows as "up" on both ends. Its almost as if the service has stopped running, but I cannot check this.

View 6 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8970 - Optimise Driver Adsl?

Mar 4, 2013

Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Telecom

Below you point out my attenuation values ​​detected on the modem in question:
Line Status:Connected
DSL Modulation Type:ADSL_2plus
Annex Type:Annex A
UpstreamDownstream
Current Rate (Kbps)4768124
Max Rate (Kbps)104811512
SNR Margin (dB)28.412.2
Line Attenuation (dB)17.233.4
Errors (Pkts) 0 0

The part adsl should be revised as the highlighted value and too discordant from the value taken on the same line as route draytek 2800 with attenuation of 24.5 db snr to 16dB, I'd like to find a job in the next firmware dedicated all'ottimizzare driver adsl modem so is worse than 6 years old

View 3 Replies View Related

TP-Link ADSL2+ Wireless :: W8970 Dropouts Connected To DirecTV DVR

Mar 3, 2013

Region : UnitedStates
Model : TD-W8970
Hardware Version : V1
ISP : CenturyLink

Just installed new W-8970 via centuryLink ADSL, connected two computers (hard wire) which work fine. I also have it connected by hard wire to my Direct T.V DVR Model HR 24 to run T.V app's such as Pandora music etc. It will only stay connected for 5-10 minutes then drops out, any suggestions other then buying a different brand modem/router.

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8970 Web Interface Doesn't Always Display Fully

Mar 13, 2013

Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :

However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: W8970 Print Server - Can't Add Printer In Control Panel

May 7, 2013

Region : Others
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :

I am struggling to get a printer added through the print server. The printer is set up in the TP-Link USB Printer Controller and selected as the auto-connect printer. I can scan through the server, but can't add the printer in control panel or see it as a option when printing. The printer is a Samsung SCX-340F.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8961NB / How To Add Other DDNS Providers

Jan 12, 2013

Region : Germany
Model : TD-W8961NB
Hardware Version : V1
Firmware Version : 1.0.0 Build 110707 Rel.32779
ISP : DTAG

would it be possible to add other DDNS providers to the router menu?E.g. I use dnsomatic.com as DDNS service (pretty much the same syntax/protocol as DynDNS, but free and more flexible).

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8960N / How To Test Routers Ddns

Jan 30, 2013

Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.54317n
ISP : century link

How do I test my routers ddns? My computer went down. So, my adsl ip address changed. I caused the modem/router to reboot. But the new ip wasn't sent to the Host (dyndns.org). I had to update my ip manually on [URL].

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8960N / URL Filter Is Not Working?

Feb 7, 2013

Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
URL Filter not working
Region : Australia
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG

Cannot get the URL filter to work Just upgraded to latest Firmware but that didn't work?

URL List Type: Deny Allow Disable
Address Port Remove

[URL]

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: How To Successfully Get VPN Passthrough Working With W8960N

Jan 24, 2013

Region : United Kingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP : ADSL24

How to successfully get VPN passthrough working with the W8960N?

I have the W8960N providing internet to local device. I want to setup a second router, TP-Link 1043ND with WW-DRT and PPTP set up to provide a separate access point for PPTP tunnelling to VPN servers outside of the UK. HideMyAss are providing VPN servers I wish to connect to.

I have followed instruction to set up both routers but would like to know if I am missing something.
First router 192.168.1.1 is basically untouched but with ports under NAT added: ports 1723 and 47 for my second router at local IP 192.168.1.111
Second router is set up according to [URL].

I know VPN work via just my first router. I can tunnel through using an Android tablet and connect to any HMA VPN server without changing anything on the 8960N.

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8961NB SIP Must Be Disabled To Let VOIP Working

Mar 20, 2013

Region : CzechRepublic
Model : TD-W8961NB
Hardware Version : V3
Firmware Version : Firmware Version : 2.0.0 Build 120823 Rel.26389
ISP : 88.103.200.11

I had a problem with this ADSL router - the VOIP outgoing calls did not work until I disabled SIP in telnet: ip nat service sip sw off.But the SIP is going to be enabled every time the router restart (or reset to default).

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8968 Remote Management Port Is Not Working?

Feb 25, 2013

Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM

The Remote Management Port is not working correctly. For whatever port I set, it will uses port 80 to access.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8968 DSL Is Working Fine But Not USB Printer Sharing

Nov 30, 2012

Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : Alice (Telecom Italia)

I have just bought this new device, installed, DSL is working fine but not the USB printer sharing. Allways tells me: "This system was not supported yet." Here is the message box: usb_printer_error.JPG.I have a HP DeskJet 1050 and a Canon Pixma MP150 machine. I know, the HP is not in the supported printer list, indeed Canon is.

View 13 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8961NB Port Forwarding (voip) Not Working

Jan 8, 2013

Region : Greece
Model : TD-W8961NB
Hardware Version : V2
Firmware Version : 2.0.0 120823
ISP : otenet

The problem is that the voip is not working. I have 2 offices with adsl connection. A is the central office and B is the branch office. The installation is old with deferent ADSL modem-router(Zyxel). The zyxel at the A office was damaged so i had to change it with Tp-link. The potology with ip and cables is the same. I tested the port forward for voip (port 1720) with telnet from outside of the office and responds correct. When i try to call from the A office to B office it seems that i can not connect. When i call from B office to A office the phone is ringing and i can not hear office B but office B hear office A. When i use the old modem router at the office A everything is working fine but the modem-router works just for a while so i have to change it. I closed the firewall but the problem is still the same. I talked with the local distributor and they tolded me that i have to correct the configuration. At the interface setup is chosen the dynamic at the section get ip and not static as i should do. The is a problem there. The configuration asks me the subnet mask and gateway. I do not know the subnet mask and either the local distributor and the local internet provider cannot assist. The internet provider told me to use at the subnet mask 255.255.255.240 and at the gateway the ip of the router. I did that but when i did i lost the internet connection. I have to mention that i make some other port forwards to my SBS2003 server and like remote desktop, vpn connections and https that works fine. The only prolbem is with the vpn port forwarding.

View 4 Replies View Related

TP-Link 300Mbps Wireless :: VPN Connection From Win 7 Client To TD-W8970?

Mar 7, 2013

Region : Australia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :

I am trying to get a windows 7 laptop to connect to a TD-W8970.

View 1 Replies View Related

Cisco Security :: 831 / DDNS Update Not Working Due To Time Out

Mar 21, 2005

I am using an 831 router and am trying to get DDNS to work.  Here is the debug output:

RESS_ASSIGN: Interface Ethernet1 assigned DHCP address 67.162.204.242, mask 255.255.254.0, hostname testlab831.xxxxxx.com
 00:53:06: DYNDNSUPD: Adding DNS mapping for testlab831.xxxxxxxx.com <=> 67.162.204.242
00:53:06: DYNDNSUPD: Sleeping for 3 seconds waiting for interface Ethernet1 configuration to settle
00:53:09: HTTPDNS: Update add called for testlab831.xxxxxxxx.com <=> 67.162.204.242
00:53:09: HTTPDNS: Update called for testlab831.xxxxxxxx.com <=> 67.162.204.242

[code]....
 
what the problem is with the "Call returned Connection time out for update testlab831.xxxxxx.com <=>" line.

View 3 Replies View Related

Protocols / Routing :: Port Forwarding TP-Link TD-W8970?

Jan 19, 2013

Router Model: TP-Link TD-W8970 port forwarding my modem/router. I previously was able to successfully port forward a Valve Source Server and had other people join on the internet so...(It worked) I recently reformatted and since have had issues.

I'm currently setup with PPPOA and I've added various ports for different programs (a Teamspeak 3 Server[9987] and Minecraft[25565]) either dont work. I used a port checker program and they either say the port is closed or the connection is refused...I've tried using a static IP but I think i configured it wrong becuase i was barely able to get the internet while using it, either way..the ports didn't open.

DCHP is disabled (Tried enabling, didn't work) The above ports are enabled with Windows firewall (inbound+outbound) and Im not using any Anti-virus software to block the ports. Windows 7 64bit, fresh format and ports that wont go through.

View 4 Replies View Related

D-Link DIR-655 :: Rev B. 2.00 DDNS And NTP Time Conflict?

Dec 23, 2010

Hooked up this router the other day to replace my old Linksys G - which has been bulletproof for 8 years. I am now wondering if I made a mistake with this unit.

I set up DDNS - after much trial and error with dyndns it now works fine.I tried to set up NTP time function - does not work. Then I set time manually. Of course on reboot it looses the time since there is no internal time function. So I need NTP.In the course of troubleshooting I turned off DDNS and behold the NTP time function now works. I turn DDNS back on and NTP does not work.

I see no logical connection between these two functions, yet the seem to interact (or not) somehow.When the NTP is not working, on reboot the time displayed in the router is the last time that I MANUALLY set the time, even though that is grayed out since I have (supposedly) activated NTP.

If I do NOTHING to NTP and uncheck DDNS, after reboot the time is correct.I tried many different NTP servers all with the same result.Looking back on-line, I see the NTP function has been a continual problem with some folks (maybe those using DDNS?) in earlier firmware. Come on DLINK don't you think it's time to get this fixed?

View 6 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8968 Virtual Server Link Missing Under Nat Menu

Mar 3, 2013

Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange

I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.

View 1 Replies View Related

D-Link DIR-615 :: DDNS Error Connecting To Members.dyndns.org:80

Sep 3, 2011

Everythings works great except thee fact that my DIR-615 router

(Hardware Version: H1  Firmware Version: 8.00) logs the following error :

[SYSTEM]: DDNS error connecting to members.dyndns.org:80

View 6 Replies View Related

D-Link DIR-655 :: Can't Seem To Make DDNS Setting Stick In Router

Mar 8, 2013

I just had to get rid of a bad DIR-825 that I replaced a trusty old DIR-655 with and now I'm back.  Anyhow, I can't seem to make the DDNS setting stick in the router.  All of the information is correct, but it doesn't seem to want to login.  When I click the enable check box, it tries connecting and then greys out and doesn't connect.

View 3 Replies View Related

TP-Link ADSL2+ Wireless :: Why TD-W8968 Use Two Channels

Apr 17, 2013

Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :

According to inSSIDer the router seems to be using two wifi channels (10+6) and inSSIDer is recommending to move to a standard channel (1,6,11).

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: W8960N Need To Add A USB HDD Server

Nov 8, 2012

Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : BT Broadband

Just got myself a new Modem/Router (TD-W8960N), and it wasn't until I had it all up and running that I realised it didn't have USB port on the back.Anyways, I was wondering how I could go about fixing this? I stumbled upon this (TP-Link TD-8817) on Amazon and wasn't sure if I could attach this to it in bridged mode or something. This has the USB socket I need. If this was all I needed, how do they connect together? I have a BT connection btw.Also, I have a Justop Android 4.0 TV Box (media player). Would this be able to see the HDD for streaming movies.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8901G - Cannot Access Some Url

Jan 12, 2013

Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version :
ISP :

problem with filtering

Region : Syria
Model : TD-W8901G
ver 6.0
54Mbps wireless G ADSL2+:

I used the url filter utility inside the router program. I put some url for example www.google.com, I wanted to try the filtering cababilty, Later I deleted all these adresses , but unfortunatley it keeps telling me the following message: "The system returned: (110) Connection timed out The remote host or network may be down. Your cache administrator is webmaster@proxy1."

View 1 Replies View Related

Using TP-LINK Wireless ADSL2+ Router As Relay Unit?

Jan 10, 2012

I use a wired network connection to my neighbours Vodafone Modem (We share his monthly cost). I also have a TP-LINK 54M Wireless ADSL2+ Router from a previous broadband contract with a landline phone company. Is it possible to reset and configure the TP-LINK Router to act as a relay unit, connected to the network cable, so I can then use my laptop elsewhere in the house?

View 3 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8961ND Doesn't Assign IP To PCs Through Another AP

Apr 1, 2013

Region : Spain
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120524 Rel.05221
ISP :
linksys1.jpg
I have wifi at home this link installed.
192.168.1.1 is a TD-W8961ND
192.168.1.4 is a linksys wrtt54gl

And I have two problems.

1) I can not see any desktops in my local net, and with old router I could see all, for example (diskstation, dm800, etc...) In my macbook air I can not see my NAS Synology and with old router I do.

2) All PCs that are conected to 192.168.1.4 have not IP. and DHCP in TD-W8961ND is activated.

View 5 Replies View Related

Tp-link Adsl2 Wireless :: Td-w8151n Can't Connect To Net From Wifi

May 7, 2013

Region : India
Model : TD-W8151N
Hardware Version : V3
Firmware Version : 120530
ISP : BSNL

Net is working smoothly from LAN, but no success on wifi. Over wi-fi, I can connect to router but cannot access net.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: W8961ND Firmware Will Not Update?

Mar 15, 2013

Region : Argentina
Model : TD-W8968
Hardware Version : V1
Region : UnitedKingdom
Firmware Version : 101029
ISP : TalkTalk

I have version 1.1 and d/l'd firmware 111125. The upgrade ran successfully to 100% and then I got the login screen again. However after checking, then restarting to factory default the version displayed was still the old one

View 3 Replies View Related

TP-Link ADSL2+ Wireless :: 42LM640S / LG Smart TV Cannot Connect

Mar 12, 2013

Model : TD-W8951ND
Hardware Version : Not Clear
Firmware Version :
ISP : Metronet BPL

I connect to the internet by BPL modem on electricity , for using my modem's wireless feature ı have to close DHCP and use modem in bridge mode, otherwise I can't use wireless, And my problem is connecting to the internet with my LG 42LM640S smart tv using wireless, When I talk with LG techinal service they came and try to connect tv to the internet with using their android phone's hotspot feature, my tv connect with phone's hotspot feature to the internet,So they said that "you have to change tp link modem's encoding system?Now it's encoding mode in WPA enconding system :S But whwen ı shut down encoding wireless tv didn't connect again?

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8961ND Trying To Connect 6 PCs But Only 4 Connecting?

Nov 13, 2012

Region : Others
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 2.0.0 Build 120427 Rel.09135
ISP : True

I just bought the wireless router as stated in the subject and I cant get 2 of our PC�s to connect wirelessly for some reason. 4 other PC's are fineAll machines running windows 7, but when the authentication type on WPA2-PSK the 2 computers ask for a password which we put in but keeps saying its wrong, but infact its right.I can connect them on WPA-PSK, but then all the computers drop out after 30 seconds.

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8960N - Cannot Disable SPI Firewall

Dec 15, 2012

Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :

According to the manual, when I go to edit my WAN connection, I should be able to enable/disable the SPI firewall. However, on my firmware I get no such option. My SPI firewall is always enabled.

I would like to be able to completely disable it when I'm testing so that I can ensure the firewall is not interfering with my tests.

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8951ND V4 - Does It Supports MAC Spoofing

Mar 31, 2013

Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version :
ISP :

The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.

View 4 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8960N / How To Open Ports

Feb 23, 2013

Region : Others
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :

Region : Sweden
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :

opening of some ports 25565 for minecraft so i can host games. i have try so solve this by my self but with zero progress. did enter the advanced setup and then i pressed on the NAT category and then i pressed on the ADD button and enter the following" [URL] and then i used a port checker to look if it worked but did not work?

View 2 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8901GB IP Address Reservation?

Feb 14, 2013

Region : CzechRepublic
Model : TD-W8901GB
Hardware Version : V3
Firmware Version : 100820
ISP : Vodafone

I have a question. Is possible for my model 8901GB v3.4 set IP adrress reservation ? I didnt find how to do it.

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: W8968 Hangs After A Few Hours?

Feb 18, 2013

Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : BSNL

I Bought this w8968 a month back.. It was working alright till a few days back. When i connect and start browsing or downloading, it goes OK.. but after a few hours(sometimes 2, sometimes 1), It stops responding and I couldn`t ping 192.168.1.1 either through WiFi/Ethernet. Status indicators for DSL/WIFI/Internet/LAN all glowing as though nothing wrong with them..? The router is not that much hot when this happens.. When i switch off the router and then on, The Prob gets solved only to reappear again in 1/2/3 hrs..

View 3 Replies View Related

TP-Link ADSL2+ Wireless :: TD8951ND - Possible To Use Router As Repeater

Apr 29, 2013

Region : Others
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Nepal Telecom

My router said it has Wireless Access Point and WDS.I think to use this router as a repeater?

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: W8968 Crashes 2 To 3 Times A Day?

Jan 10, 2013

Region : Spain
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : Telefonica-Spain

'm having the same problem my tp-link freezes several times a day and only a hard reset will get it working again. I have no idea how to fix it, I have contacted tp-link support and they say to make sure I have all the right ADSL configuration parameters.

View 7 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8980 Test DNS Root

Feb 18, 2013

Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :

Another query regarding diagnostic test and Test DNS Root. It always fails why?

View 4 Replies View Related

ADVERTISEMENT