TP-Link Dual-Band Wireless :: TL-WDR4300 - DHCP Not Dealing Addresses After Few Hours?
Dec 9, 2012
Region : Poland
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : [url]...
I'm having issues with DHCP server not dealing IP after few hours (varies between 1h and 8h) of torrent traffic. If no continuous torrent traffic is applied, the problem does not occur. New wireless devices connect to the wi-fi network, but get stuck on 'getting IP adress'. The problem is with DHCP service or the wireless network service. New wired devices receive IP. The problem is only with wireless devices. I have no additional wireless device, that I can configure the network settings on my own (only phones) to check if it works without DHCP server giving IP. Wired connection is stable, but the bandwidth usage curve becomes somewhat similar to a sinewave.
I did disable the hardware NAT because that feature made the router unstable and caused it to hang up within minutes.
View 7 Replies
ADVERTISEMENT
Dec 26, 2012
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I got a new TP-Link TL-WDR4300, connected it to my online pure sine wave UPS like I did with my previous routers with no problem.After about 24 hours, router crashes - no access to web interface, no internet (wired or wireless), must reboot to get it to work again.Router was replaced, same problem with new router.The firmware is the latest one and is customized for Israel because of 5GHz limitations.I was told by the representative in Israel that I should try to connect it to another AC outlet instead of the UPS.
View 7 Replies
View Related
Jan 28, 2013
Region : Philippines
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
I have a PROLiNK H5001N ADSL Wireless Modem using bridge mode to my TL-WDR4300. I login to my ISP using the TL-WDR4300 with secondary connection to my modem so that I can open the modem setup page.
1.) My question is can the Prolink get DHCP address from the Wan Port of TL-WDR4300?
2.) Can I still use the Wifi of the modem to get internet?
3.) If I connect my ISP to Prolink then connect TL-WDR4300 thru static connection, will the NAT and Hardware NAT still work in the TL-WDR4300?
NOTE: the latest firmware built TL-WDR4300_V1_121225 seams to have internet connection lost problem after a few minutes. I reverted back to 3.12.23 and the problem is gone.
View 3 Replies
View Related
Dec 6, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Comcast
So I've been checking my router DHCP list and I usually use the WPS feature to add devices. I know how many devices I have and which ones are wireless etc. I've made address reservations on all the devices that I have and know of. One feature that really frustrates me (which is missing) is no way to rename a device. My iPhone is named: Reggie's iPhone yet the 4300 picks it up as Unknown... I dont understand why. I've renamed it on the iPhone to different things and restarted it but still it comes up as that. I have 2 Nexus 7s and both come up with wierd names, one is for my wife and one is for me and I wish there was a way to name it proper.
Question is: Will the name edit feature ever get added to it? I dont get why it's not there now, it's not really something major (I have a 5 year old router that even has that... and it cant even support N). It's really frustrating to have to guess and check the devices on my network because most of them come up as unknowns.
Right now I'm trying to located another device that's coming up as unknown and now matter how much I try, since the router lacks any feature to assist finding it, it's really frustrating.
something else i noticed: my DHCP List shows all the devices connected with their IP addresses, yet I went into CMD and was doing a random ping command. I'm able to ping 192.168.0.114 with perfect stats back yet on my DHCP List it shows the highest IP is at 192.168.0.112.... Is something wrong here? Is it supposed to not pick up the IPs it gives out? And of course since there isnt a way to tell if that IP is for a WIFI or ethernet device, I have no idea what that device is...
yet i found another ip address on my network by using the ping command. actually I went ahead and did arp -a to find out all the ips with mac addresses. this is a serious flaw with the security of this router!!
View 2 Replies
View Related
Apr 15, 2013
Region : Hongkong
Model : TL-WDR4300
Hardware Version : V1
During long, heavy download streams (such as BT, video streaming) the router WDR4300 would still lock up the internet (WAN) connection for that client. I could still go to the admin web page on that client but no internet activity would occur until either rebooting the router.
View 8 Replies
View Related
Dec 31, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Comcast
I have no problems connecting on a 5 GHz band or wired to the router. However any device connecting on 2.4 Ghz gets barely any bandwidth and drops after running for a short time. I have test numerous devices and have the same issue. What was odd is a device on 5GHz that worked fine had the same issue when connecting on 2.4 GHz which seems to say it is only that band. I have an old router that works fine on 2.4 GHz on channel 1 with all the security settings I used on the 4300.
View 14 Replies
View Related
Jan 6, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : latest
ISP : Clear
Get GMT throws an error. I set known good public NTP servers, still get error. Also power cycling or rebooting the router seems to drop manual time settings, as well. I am using WDR4300 as a wireless access point, does that matter? Maybe I don't need time in access mode? It is connected to the Internet and is providing internet access to clients.
View 1 Replies
View Related
Mar 28, 2013
Region : Venezuela
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP :
I have an issue with my TL-WDR4300 (regular, internet sharing use, no Open WRT or similar things). It was working well, until one day that my devices only receive the 2.4 GHz signal (no 5 GHz) and then I try to connect to 2.4 GHz and it asks for a password. I put my regular password and it doesn't work. Then I tried to bring it to factory default settings, I push the reset button for 8 seconds as the manual points and then same thing. What could I do?
View 2 Replies
View Related
Jan 14, 2013
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : plusnet
How do I get the full 450 Mbps out of my router on the status it saying 300Mbps
View 5 Replies
View Related
Nov 21, 2012
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
Region : Others
I have Enable WDS Bridging and run Survey which detect the other SSID to be joined with the correct MAC address.I had filled the password of my second THOMSON v 585 V7 with the correct Auth Type both routers broadcast on channel 11.But my TP-Link 2543ND cannot made it work.I also disable DHCP and changed my LAN ip to 192.168.1.2 and can access it over my lan.
View 1 Replies
View Related
Mar 5, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
The router is working and when I plug in an external drive to usb I can see in the admin tool. It is setup to share without a password. I am using a PC with Vista on it...so I go to RUN and enter [URL] but I get the following message:'Windows cannot access [URL]
View 2 Replies
View Related
Feb 11, 2013
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 121225
ISP : Online
Recently I replaced my Linksys WRT54G for a TP-Link WDR4300. But unfortunately this did not result in an increased speed.On both the 5GHz and 2.4GHz speed is limited to roughly 2.5-3 MByte/s, which is OK for watching movies etc. but I could reach those speeds with the 802.11g router as well!
I'm using the WDR4300 as access point, so I disabled DHCP server and NAT functionality, left the WAN port empty. And I set fixed IP in the subnet range of my modem/router. (horrible Speedtouch device). All works fine and stable, but too slow.
In the wireless settings I tried the 20 and 40MHz bandwith, disabled WMM, tried to lower the transmission power, tried to set a fixed channel. But all those changes do not have a significant influence on the transfer speed. (both on 2.4 and 5GHz) I'm the only 5GHz access point in my neighborhood, so interference cannot be a problem.
The clients indicate a link speed of 300mbps very close to the router, and this drops to indication of 54mbps further away, but effective link speed remains fairly constant (and stable!) (I find it strange that indicated link speed already drops at 3 meters with clear line of sight to the router)
I did the tests with fixed IPs on two laptops and no devices connected on the LAN ports, to rule out problems caused by the modem/router or other clients.The tests were done using a Lenovo x220 and Asus Zenbook, both with Intel dual band 802.11n wifi interfaces. The Lenovo reaches 22MByte/s via the Cisco access point at my work (with less signal as at home).
View 6 Replies
View Related
Dec 6, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP : Verizon DSL
My DSL connection comes into our house in the basement and the DSL modem came with a router included. I bought the WDR4300 for the higher speed wireless connections and the gigabit ports. I really don't need the "router" functionality. I would like to put the WDR4300 on the second floor to give (hopefully) the broadest wireless range. However, I would like all my PCs (including those wirelessly connected) to be on the same sub-net. Is there a way to configure the WDR4300 so it acts like a switch rather than a router?
View 1 Replies
View Related
Nov 7, 2012
Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Waoo, fiber
i just bought a WDR4300. tried the quick start, then tried to manually set it up like my old Router. but i cant connect to the internet. when i check the status. it often says that WAN is unplugged, no cable. But when i use same cabels and settings on my old router it works fin.
View 2 Replies
View Related
Feb 14, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : charter, its smarter.
so i have a sb6141 cable modem that is mine and not a lease. it works like a champ when hard wired to my desktop. i just got my hands on a new shiny tp-link wdr4300 yesterday and after messing with it for the better part of 2 hours, something seems to be amiss with the communication between the two. everything will be humming along fine and all of a sudden i get the dreaded PAGE CANNOT BE DISPLAYED. sure as the world i look at the modem and all the lights are off and its resetting itself. and honestly this continues until i pull the power and plug it back up. i think maybe one time in the middle of the night i actually saw it reset itself and then come back online.
View 1 Replies
View Related
Feb 25, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : fullrate.dk
My ISP has provided me a router: Zyxel P-2601HN which has an ideal WLAN transfer rate of 150 mbps. I live in a concrete 2 story house so signals are weak at best on the other floor - therefore, I Have bought the TL-WDR4300 as an extension for the latter floor. I have connected the routers from LAN to LAN and the Zyxel has 192.168.1.1 on LAN and the TL-WDR4300 had 192.168.0.1 as out set. I have changed this to 192.168.1.2 and all the setup (disabled DHCP + other) seems to work alright. BUT i can not log into the TL-WDR4300 !! Not with http://192.168.1.2 and not with [URL]. What I can do to get into the setup of TL-WDR4300. I know I can alays backup the setting and reset the router and load the setting again, make alterations, saving .....but it kind of drastic !Can the two radios SSID names (2,4 MHz and 5 MHz) be the same name as the SSID name on the Zyxel P-2601HN ? What are the implications ?
View 3 Replies
View Related
Nov 6, 2012
Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Arrownet
I purchased a WDR4300 yesterday and have set it up. The internet is running smoothly although the transfer speed is rather slow. When transferring from my computer to my Seagate GoFlex Home i get about 6 - 8 mbps with Wireless N. The router is set to only use Wireless-N and my laptop has the latest drivers. I have also tried other computers in the house and the speed is the same. The GoFlex Home is connected to the router via a LAN cable. Prior to updating i used a Linksys WRT54GL and managed speeds of about 3 or 4 mbps over its G only connection. As for transfers between 2 computes the rate is about 1 - 3 mbps
As for distance the Wireless router is only about 1.5 meters from the laptop (across the room) with nothing in between them to cause interference. I have also checked what channels my neighbors use (using inSSIDer) and picked 13 as there is only 1 other person nearby on that channel and they are quite far away.
View 5 Replies
View Related
Jan 6, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : time warner
This is frustrating I owned the router for about 2 weeks. my 2.4ghz is out. Basically I connect to the router on 2.4 can get into the tp-link admin webpage for the router but no internet at all. if I switch to 5 ghz everything works great, or if i use direct connect wire everything is great. I tried disabling NAT but that shut down all my internet connections across all links and manually switching to channel 1 did nothing at all i also tried channel 7. Ideas why only 2.4 ghz is affected out of the blue all of a sudden?
View 12 Replies
View Related
May 11, 2013
Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4300_V1_130319
ISP : unfi
I unable connect to internet after upgrade the new firmware
View 1 Replies
View Related
Dec 10, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Comcast
The 5 ghz connects fine for multiple machines however machines on 2.4 simultaneously lose their connection to the internet, sometimes saying it is still connected to the internet when it is not and sometimes losing connection with the router entirely. The 5ghz still works when this happens.
View 14 Replies
View Related
Mar 10, 2013
Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I've been using inSSider on Windows and trying different settings on my 4300 to get wireless n @ 300MHz working with no luck. The maximum I seem to be able to get it to run is 144MHz.
Is this a fault with the router or the firmware? Since the router is advertised to run at 300Mhz, then by rights if it does not or cannot, then TP-Link owes everyone a refund, at least in Australia because this counts as false advertising.
I had a similar issue with my 1043ND as well. Has anyone got a 4300 working at 300 MHz?
View 3 Replies
View Related
Apr 10, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :
Setting up access control for one PC. I just want to block all internet access to one PC during a certain time. It seems like my only options in the Access Control page in the GUI is to block websites or domains.
View 4 Replies
View Related
Jan 8, 2013
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I recently bought the N750 wireless dual band router and I would like to setup a bridge with another router that I'm currently using.
I have followed the instructions in the documentation [URL]. But I've had 0 success in getting this to work.
How to get this feature to work?
Additional info:
I followed each step to the letter. In the last step when my router reboots I noticed that the System light doesn't flash. Which indicates that there is a system error (according to the user manual). But I'm unable to determine what the system error is because I can no longer log into my router's Administration page anymore.
in the instructions (link above) it says to disable DHCP, so I manually assign an IP address to my computer setting the gateway IP address to the IP address I manually assigned to my router. I can see that a connection to the router is established, but I'm unable connect to the internet and when I type in the IP address of my router I'm unable to get into the administration menu.
I checked the wireless connections on my source router and I don't see the IP address of the N750 router.
View 5 Replies
View Related
Feb 17, 2013
Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I need to capture packets from my device out to the internet... are there any utilities or something that I can use to hook into the router to do a packet capture for a device on my network so I can give my ISP some troubleshooting data.
View 1 Replies
View Related
Jan 28, 2013
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 121225
ISP :
I bought this router to replace my WNDR3700v1 (by Netgear).Although on short distance the Netgear is outperformed, on the other site of the house the 2,4GHz signal is lost often (where the Netgear would still work). Both routers are located on the same location (not simultaneously) and settings are identical (channel, band, security, etc.).
I was wondering if I could get more performance out of the TP-Link by positioning the antennas in different angles. All antennas were positioned vertically and I also tried having the outer antennas under 30 degrees.
View 2 Replies
View Related
Feb 14, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.
View 7 Replies
View Related
Feb 13, 2013
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Sky
how to deselect the WMM option on the advanced wireless settings? The box is ticked and it won't allow me to deselect it?Model number TD-W8980
View 3 Replies
View Related
Mar 31, 2013
Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : TM UNIFI
I have recently bought a dual band router to replace the aging default router supply by the ISP.
After setting up, I found the message "No Internet Connection". I have checked the log and found that PPPoE was connected. However I am connect to the internet.
View 7 Replies
View Related
Mar 15, 2013
Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Fullrate
No matter what I try, the signal strength never gets better that 30%, even when I have my laptop next to the router. I have tried various settings (found in these forums), but nothing seem to work. My old D-Link performed better, both close and over distances.
View 2 Replies
View Related
Jan 23, 2013
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.17 Build 120426 Rel.29216n
ISP :
In the absence of true QoS capability on the 4300, what is the best way to give bandwidth priority to one of my network devices?
I have an Apple Airport Extreme connected to my network. It is used to stream music from my Ipod to my sound system. I do this through my network (rather then connecting the IPod directly to the AE) so that I can connect to radio stations over the internet. The problem is that I'm getting random dropouts (pauses in streaming). I've shut down everything on the IPod to make sure that there are no Apps competing for WIFI resources. The dropouts happen even if there is little activity on the network (e.g., file downloads, youtube, etc.)
What I want to do is to get the 4300 to give top priority to the AE. How can I do this without QoS capability? Can I allocate more bandwidth to the AE when it is receiving streaming data?
Note: The AE is always connected to the network. It uses DHCP to get it's IP address. It is connected to the 5G band. Signal strength is typically 1 to 2 of 3 bars (average is 1.5 bars). The 2.4G band has a slightly higher signal strength but the same dropouts occur so the problem does not appear to be signal strength.
View 1 Replies
View Related
Apr 30, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I will never ever buy anything Chinese bricked.
View 1 Replies
View Related
Dec 5, 2012
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Just got my new TL-WDR4300 router. Set it up last night with the latest firmware. I can connect to Internet using a wired cable. However, I can't connect to Internet via wifi. I already tried 2 laptops (Vista & Win XP) and 2 tablets - I can see my wifi signal, connect to it (with my password), even obtained IP address (from ipconfig). However, when I tried to open a web page (eg google), it can't connect to Internet (always got timeout or service not found). Again, same laptop has no problem if I use a cable to connect to my router.
View 3 Replies
View Related
Mar 21, 2013
Canada
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]
Is it possible to disable broadcasting that the WDR4300 is made by TP-Link? I want to continue to broadcast the SSID but not the manufacturer. I have looked in the various menu pages and cannot figure out how to have this happen.
View 14 Replies
View Related